Change certain CPP conditionals into C conditionals, which should be possible for the compiler to optimize at runtime. This makes the source code easier to read.
According to the CC1310LP design files, the flash on it is the same as the flash on the CC2650 LP (MX25R8035F 8Mbit). However, the flash on some CC1310 LPs reportedly identifies itself as the 16Mbit one (MX25R1635F). Instruction sets are identical, we simply need to tell the driver to recognise this part's Device ID.
The block that controls the `.upload` target is unnecessarily replicated in multiple sub-board Makefiles. This was originally done because the SmartRF and the Launchpad can be programmed with the c2538-bsl script, whereas the sensortag cannot.
This commit moves the `cc2538-bsl` / `.upload` target logic to the top level cpu Makefile (`cpu/cc26xx-cc13xx/Makefile.cc26xx-cc13xx`). Board makefiles simply set the make variable `BOARD_SUPPORTS_BSL` to 1 to signal that they can be programmed by the BSL script. If `BOARD_SUPPORTS_BSL` is not equal to 1, trying to use the `.upload` target will return an error message.
For example:
```
$ make BOARD=sensortag/cc2650 cc26xx-demo.upload
using saved target 'srf06-cc26xx'
This board cannot be programmed with the ROM bootloader and therefore does not support the .upload target.
```
Two errors have been spotted, when IPv6 is enabled in the ravenusb
Project-Makefile:
#CONTIKI_NO_NET=1
CONTIKI_WITH_IPV6=1
The compile error results from a variable name mismatch in cdc_task.c
The variable 'r' is undeclared and should be renamed to 'route'
The linker also fails with 'undefined references'
This has been mediated by adding 'core/net' to Modules in the
Project-Makefile.
This patch adds a simple non-driver protection domain sample to serve
as an example for defining other non-driver protection domains. It
simply performs a ping-pong test of protection domain switching
latency during boot, including optional accesses to a private metadata
region, and prints out the results.
This patch extends the protection domain framework with an additional
plugin to use Task-State Segment (TSS) structures to offload much of
the work of switching protection domains to the CPU. This can save
space compared to paging, since paging requires two 4KiB page tables
and one 32-byte page table plus one whole-system TSS and an additional
32-byte data structure for each protection domain, whereas the
approach implemented by this patch just requires a 128-byte data
structure for each protection domain. Only a small number of
protection domains will typically be used, so
n * 128 < 8328 + (n * 32).
For additional information, please refer to cpu/x86/mm/README.md.
GCC 6 is introducing named address spaces for the FS and GS segments
[1]. LLVM Clang also provides address spaces for the FS and GS
segments [2]. This patch also adds support to the multi-segment X86
memory management subsystem for using these features instead of inline
assembly blocks, which enables type checking to detect some address
space mismatches.
[1] https://gcc.gnu.org/onlinedocs/gcc/Named-Address-Spaces.html
[2] http://llvm.org/releases/3.3/tools/clang/docs/LanguageExtensions.html#target-specific-extensions
This patch implements a simple, lightweight form of protection domains
using a pluggable framework. Currently, the following plugin is
available:
- Flat memory model with paging.
The overall goal of a protection domain implementation within this
framework is to define a set of resources that should be accessible to
each protection domain and to prevent that protection domain from
accessing other resources. The details of each implementation of
protection domains may differ substantially, but they should all be
guided by the principle of least privilege. However, that idealized
principle is balanced against the practical objectives of limiting the
number of relatively time-consuming context switches and minimizing
changes to existing code.
For additional information, please refer to cpu/x86/mm/README.md.
This patch also causes the C compiler to be used as the default linker
and assembler.
This patch configures Isolated Memory Regions (IMRs) to block DMA to
code and data regions that do not contain any data that needs to be
DMA-accessible.
The Intel Quark X1000 SoC includes support for Isolated Memory Regions
(IMRs), which are specified using range registers and associated
control registers that are accessible via the message bus. This patch
adds a driver for accessing those registers.
The Intel Quark X1000 SoC includes a message bus that is accessible
via PCI configuration registers. It communicates to various SoC
components such as the Isolated Memory Region (IMR) registers and the
Remote Management Unit. This patch adds a driver for accessing the
message bus.
This patch revises the I2C and GPIO initialization code to always be
run during platform boot rather than within each process that requires
it.
This patch also revises the gpio-output example to use a pin that is
set as an output by the default pinmux configuration. Previously, it
used a pin that was set as an output by the pinmux configuration that
is in effect when the OS does not change the pinmux configuration.
This patch permits interrupts to be generated by both the I2C and GPIO
controllers for simultaneously-executing applications. The controllers
share a single interrupt pin, INTC. Prior to this patch,
quarkX1000_gpio_init() routed INTA to PIRQC and IRQ 10 (due to an
incorrect assumption that INTA is connected to the GPIO controller),
and quarkX1000_i2c_init() routed INTC to PIRQC and IRQ 9. The I2C
controller initialization is a prerequisite for GPIO initialization,
so the final configuration was that INTA and INTC were both routed to
PIRQC and IRQ 10. Thus, only the GPIO ISR was being invoked, even if
the I2C controller was actually responsible for the interrupt.
This patch refactors the I2C and GPIO ISR setup and handler code so
that the shared portions are combined in
cpu/x86/drivers/legacy_pc/shared-isr.[ch]. The I2C and GPIO drivers
communicate their interrupt information to the shared component by
placing structures in a specific section of the binary.
This commit creates a `common` directory, aimed to host drivers supported by multiple boards of the CC13xx/CC26xx family.
We move the Sensortag SPI and External Flash drivers to this location and we change the Sensortag build system to pull the respective files from therein.
The driver currently supports two Winbond external flash parts with identical instruction sets. The instruction set of the Macronix MX25R8035F appears to be a superset. We therefore change the driver to add the MID/DID of the Macronix to the list of supported parts.
This will subsequently allow us to share the same driver for both the SensorTag and the CC2650 LauchPad.
This patch revises the compiler flags when LLVM Clang is in use to
cause Clang to automatically use its built-in header files rather than
those for GCC.
Also added a 2-minutes average wind direction value, replaced the 240 bytes buffer from the reference example, but probably there's room for efficiency improvement
