Adjust READMEs to point explicitly to the arm-gcc version used by travis
This commit is contained in:
parent
0d0e44036b
commit
9e9e6d07b0
|
@ -66,21 +66,15 @@ The platform has been developed and tested under Windows XP, Mac OS X 10.9.1 and
|
|||
|
||||
Install a Toolchain
|
||||
-------------------
|
||||
The toolchain used to build contiki is arm-gcc, also used by other arm-based Contiki ports. If you are using Instant Contiki, you will have a version pre-installed in your system. To find out if this is the case, try this:
|
||||
The toolchain used to build contiki is arm-gcc, also used by other arm-based Contiki ports. If you are using Instant Contiki, you may have a version pre-installed in your system.
|
||||
|
||||
$ arm-none-eabi-gcc -v
|
||||
Using built-in specs.
|
||||
Target: arm-none-eabi
|
||||
Configured with: /scratch/julian/lite-respin/eabi/src/gcc-4.3/configure
|
||||
...
|
||||
(skip)
|
||||
...
|
||||
Thread model: single
|
||||
gcc version 4.3.2 (Sourcery G++ Lite 2008q3-66)
|
||||
The platform is currently being used/tested with "GNU Tools for ARM Embedded Processors" (<https://launchpad.net/gcc-arm-embedded>). The current recommended version and the one being used by Contiki's regression tests on Travis is shown below.
|
||||
|
||||
The platform is currently being used/tested with "GNU Tools for ARM Embedded Processors". This is the recommended version and the one being used by Contiki's regression tests on Travis. <https://launchpad.net/gcc-arm-embedded>
|
||||
|
||||
The older version (Sourcery G++ Lite 2008q3-66) shown above should still work, but the port is no longer being tested with it. <http://sourcery.mentor.com/public/gnu_toolchain/arm-none-eabi>
|
||||
$ arm-none-eabi-gcc --version
|
||||
arm-none-eabi-gcc (GNU Tools for ARM Embedded Processors) 5.2.1 20151202 (release) [ARM/embedded-5-branch revision 231848]
|
||||
Copyright (C) 2015 Free Software Foundation, Inc.
|
||||
This is free software; see the source for copying conditions. There is NO
|
||||
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
|
||||
Drivers
|
||||
-------
|
||||
|
|
|
@ -58,12 +58,15 @@ To use the port you need:
|
|||
Note that uploading over serial doesn't work for the Sensortag, you can use
|
||||
TI's SmartRF Flash Programmer in this case.
|
||||
* A toolchain to build firmware: The port has been developed and tested with
|
||||
GNU Tools for ARM Embedded Processors <https://launchpad.net/gcc-arm-embedded>.
|
||||
The port was developed and tested using this version:
|
||||
GNU Tools for ARM Embedded Processors (<https://launchpad.net/gcc-arm-embedded>).
|
||||
The current recommended version and the one being used by Contiki's regression
|
||||
tests on Travis is shown below.
|
||||
|
||||
$ arm-none-eabi-gcc -v
|
||||
[...]
|
||||
gcc version 4.9.3 20141119 (release) [ARM/embedded-4_9-branch revision 218278] (GNU Tools for ARM Embedded Processors)
|
||||
$ arm-none-eabi-gcc --version
|
||||
arm-none-eabi-gcc (GNU Tools for ARM Embedded Processors) 5.2.1 20151202 (release) [ARM/embedded-5-branch revision 231848]
|
||||
Copyright (C) 2015 Free Software Foundation, Inc.
|
||||
This is free software; see the source for copying conditions. There is NO
|
||||
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
|
||||
* srecord (http://srecord.sourceforge.net/)
|
||||
* You may also need other drivers so that the SmartRF can communicate with your
|
||||
|
|
|
@ -74,22 +74,15 @@ To start using Contiki, the following is required:
|
|||
|
||||
Install a Toolchain
|
||||
-------------------
|
||||
The toolchain used to build contiki is arm-gcc, also used by other arm-based Contiki ports. If you are using Instant Contiki, you will have a version pre-installed in your system. To find out if this is the case, try this:
|
||||
The toolchain used to build contiki is arm-gcc, also used by other arm-based Contiki ports. If you are using Instant Contiki, you may have a version pre-installed in your system.
|
||||
|
||||
$ arm-none-eabi-gcc -v
|
||||
Using built-in specs.
|
||||
Target: arm-none-eabi
|
||||
Configured with: /scratch/julian/lite-respin/eabi/src/gcc-4.3/configure
|
||||
...
|
||||
(skip)
|
||||
...
|
||||
Thread model: single
|
||||
gcc version 4.3.2 (Sourcery G++ Lite 2008q3-66)
|
||||
The platform is currently being used/tested with "GNU Tools for ARM Embedded Processors" (<https://launchpad.net/gcc-arm-embedded>). The current recommended version and the one being used by Contiki's regression tests on Travis is shown below.
|
||||
|
||||
The platform is currently being used/tested with the following toolchains:
|
||||
|
||||
* GNU Tools for ARM Embedded Processors. This is the recommended version. Works nicely on OS X. <https://launchpad.net/gcc-arm-embedded>
|
||||
* Alternatively, you can use this older version for Linux. At the time of writing, this is the version used by Contiki's regression tests. <https://sourcery.mentor.com/public/gnu_toolchain/arm-none-eabi/arm-2008q3-66-arm-none-eabi-i686-pc-linux-gnu.tar.bz2>
|
||||
$ arm-none-eabi-gcc --version
|
||||
arm-none-eabi-gcc (GNU Tools for ARM Embedded Processors) 5.2.1 20151202 (release) [ARM/embedded-5-branch revision 231848]
|
||||
Copyright (C) 2015 Free Software Foundation, Inc.
|
||||
This is free software; see the source for copying conditions. There is NO
|
||||
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
|
||||
Drivers
|
||||
-------
|
||||
|
|
Loading…
Reference in a new issue