317 lines
11 KiB
C
317 lines
11 KiB
C
/*
|
|
* Copyright (c) 2012, Texas Instruments Incorporated - http://www.ti.com/
|
|
* Copyright (c) 2016, Zolertia <http://www.zolertia.com>
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/**
|
|
* \addtogroup zoul-platforms
|
|
* @{
|
|
*
|
|
* \defgroup zolertia-orion-ethernet-router Zolertia IoT Orion Ethernet Router
|
|
*
|
|
* The Zolertia Orion Router includes an Ethernet ENC28J60 controller with
|
|
* active POE (power over ethernet), operating over IPv4/IP64. It features a
|
|
* dual RF interface (2.4GHz and 863-950MHz) with external antenna connectors,
|
|
* a power on/off switch and programable user button.
|
|
*
|
|
* This file provides connectivity information on LEDs, Buttons, UART and
|
|
* other peripherals
|
|
*
|
|
* @{
|
|
*
|
|
* \file
|
|
* Header file with definitions related to the I/O connections on the Zolertia's
|
|
* Orion Ethernet Router, Zoul-based
|
|
*
|
|
* \note Do not include this file directly. It gets included by contiki-conf
|
|
* after all relevant directives have been set.
|
|
*/
|
|
#ifndef BOARD_H_
|
|
#define BOARD_H_
|
|
|
|
#include "dev/gpio.h"
|
|
#include "dev/nvic.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name Orion Ethernet Router LED configuration
|
|
*
|
|
* LEDs on the eth-gw are connected as follows:
|
|
* - LED1 (Red) -> PD5
|
|
* - LED2 (Green) -> PD4
|
|
* - LED3 (Blue) -> PD3
|
|
* @{
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Some files include leds.h before us, so we need to get rid of defaults in
|
|
* leds.h before we provide correct definitions */
|
|
#undef LEDS_GREEN
|
|
#undef LEDS_YELLOW
|
|
#undef LEDS_BLUE
|
|
#undef LEDS_RED
|
|
#undef LEDS_CONF_ALL
|
|
|
|
/* In leds.h the LEDS_BLUE is defined by LED_YELLOW definition */
|
|
#define LEDS_GREEN (1 << 4) /**< LED1 (Green) -> PD4 */
|
|
#define LEDS_BLUE (1 << 3) /**< LED2 (Blue) -> PD3 */
|
|
#define LEDS_RED (1 << 5) /**< LED3 (Red) -> PD5 */
|
|
|
|
#define LEDS_CONF_ALL (LEDS_GREEN | LEDS_BLUE | LEDS_RED)
|
|
|
|
#define LEDS_LIGHT_BLUE (LEDS_GREEN | LEDS_BLUE) /**< Green + Blue (24) */
|
|
#define LEDS_YELLOW (LEDS_GREEN | LEDS_RED) /**< Green + Red (48) */
|
|
#define LEDS_PURPLE (LEDS_BLUE | LEDS_RED) /**< Blue + Red (40) */
|
|
#define LEDS_WHITE LEDS_ALL /**< Green + Blue + Red (56) */
|
|
|
|
/* Notify various examples that we have LEDs */
|
|
#define PLATFORM_HAS_LEDS 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name USB configuration
|
|
*
|
|
* The USB pullup for D+ is not included in this platform
|
|
*/
|
|
#ifdef USB_PULLUP_PORT
|
|
#undef USB_PULLUP_PORT
|
|
#endif
|
|
#ifdef USB_PULLUP_PIN
|
|
#undef USB_PULLUP_PIN
|
|
#endif
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name UART configuration
|
|
*
|
|
* On the eth-gw, the UARTs are connected to the following ports/pins:
|
|
*
|
|
* - UART0:
|
|
* - RX: PA0, connected to CP2104 serial-to-usb converter TX pin
|
|
* - TX: PA1, connected to CP2104 serial-to-usb converter RX pin
|
|
* - UART1:
|
|
* - RX: PC1
|
|
* - TX: PC0
|
|
* - CTS: not used
|
|
* - RTS: not used
|
|
*
|
|
* We configure the port to use UART0 and UART1, CTS/RTS only for UART1,
|
|
* both without a HW pull-up resistor.
|
|
* UART0 is not exposed anywhere, UART1 pins are exposed over the JP9 connector.
|
|
* @{
|
|
*/
|
|
#define UART0_RX_PORT GPIO_A_NUM
|
|
#define UART0_RX_PIN 0
|
|
#define UART0_TX_PORT GPIO_A_NUM
|
|
#define UART0_TX_PIN 1
|
|
|
|
#define UART1_RX_PORT GPIO_C_NUM
|
|
#define UART1_RX_PIN 1
|
|
#define UART1_TX_PORT GPIO_C_NUM
|
|
#define UART1_TX_PIN 0
|
|
#define UART1_CTS_PORT (-1)
|
|
#define UART1_CTS_PIN (-1)
|
|
#define UART1_RTS_PORT (-1)
|
|
#define UART1_RTS_PIN (-1)
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/** \name Zolertia Orion Router button configuration
|
|
*
|
|
* Buttons on the eth-gw are connected as follows:
|
|
* - BUTTON_USER -> PA3, S1 user button, shared with bootloader
|
|
* - BUTTON_RESET -> RESET_N line
|
|
* @{
|
|
*/
|
|
/** BUTTON_USER -> PA3 */
|
|
#define BUTTON_USER_PORT GPIO_A_NUM
|
|
#define BUTTON_USER_PIN 3
|
|
#define BUTTON_USER_VECTOR GPIO_A_IRQn
|
|
|
|
/* Notify various examples that we have Buttons */
|
|
#define PLATFORM_HAS_BUTTON 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name ADC configuration
|
|
*
|
|
* These values configure which CC2538 pins and ADC channels to use for the ADC
|
|
* inputs. There pins are suggested as they can be changed, but note that only
|
|
* pins from PA can be configured as ADC.
|
|
*
|
|
* The Zolertia eth-gw, as it is, only allows 3.3VDC sensors.
|
|
*
|
|
* The internal ADC reference is 1190mV, use either a voltage divider as input,
|
|
* or a different voltage reference, like AVDD5 or other externally (AIN7 or
|
|
* AIN6).
|
|
*
|
|
* The ADC1 is exposed over the JP9 connector
|
|
* @{
|
|
*/
|
|
#define ADC_SENSORS_PORT GPIO_A_NUM /**< ADC GPIO control port */
|
|
#define ADC_SENSORS_ADC1_PIN 2 /**< ADC1 to PA2, 3V3 */
|
|
#define ADC_SENSORS_ADC2_PIN 4 /**< ADC2 to PA4, 3V3 */
|
|
#define ADC_SENSORS_ADC3_PIN 5 /**< ADC3 to PA5, 3V3 */
|
|
#define ADC_SENSORS_ADC4_PIN 6 /**< ADC4 to PA6, 3V3 */
|
|
#define ADC_SENSORS_ADC5_PIN (-1) /**< Not used */
|
|
#define ADC_SENSORS_ADC6_PIN (-1) /**< Not used */
|
|
#define ADC_SENSORS_MAX 4 /**< PA2, PA4, PA5, PA6 */
|
|
|
|
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name SPI (SSI0) configuration
|
|
*
|
|
* These values configure which CC2538 pins to use for the SPI (SSI0) lines,
|
|
* reserved exclusively for the CC1200 RF transceiver.
|
|
* TX -> MOSI, RX -> MISO
|
|
* @{
|
|
*/
|
|
#define SPI0_CLK_PORT GPIO_B_NUM
|
|
#define SPI0_CLK_PIN 2
|
|
#define SPI0_TX_PORT GPIO_B_NUM
|
|
#define SPI0_TX_PIN 1
|
|
#define SPI0_RX_PORT GPIO_B_NUM
|
|
#define SPI0_RX_PIN 3
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name SPI (SSI1) configuration
|
|
*
|
|
* These values configure which CC2538 pins to use for the SPI (SSI1) lines,
|
|
* reserved exclusively for the ENC28J60 ethernet module. These pins should not
|
|
* be used for other use, unless you really know what you are doing
|
|
* TX -> MOSI, RX -> MISO
|
|
* @{
|
|
*/
|
|
#define SPI1_CLK_PORT GPIO_C_NUM
|
|
#define SPI1_CLK_PIN 4
|
|
#define SPI1_TX_PORT GPIO_C_NUM
|
|
#define SPI1_TX_PIN 5
|
|
#define SPI1_RX_PORT GPIO_C_NUM
|
|
#define SPI1_RX_PIN 6
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name I2C configuration
|
|
*
|
|
* As default there is not a default pin assignment for I2C, change this values
|
|
* accordingly if mapping either pin to the I2C controller.
|
|
* @{
|
|
*/
|
|
#define I2C_SCL_PORT GPIO_C_NUM
|
|
#define I2C_SCL_PIN 3
|
|
#define I2C_SDA_PORT GPIO_C_NUM
|
|
#define I2C_SDA_PIN 2
|
|
#define I2C_INT_PORT GPIO_D_NUM
|
|
#define I2C_INT_PIN 2
|
|
#define I2C_INT_VECTOR GPIO_D_IRQn
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Dual RF interface support
|
|
*
|
|
* Enables support for dual band operation (both CC1200 and 2.4GHz enabled).
|
|
* @{
|
|
*/
|
|
#define REMOTE_DUAL_RF_ENABLED 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name CC1200 configuration
|
|
*
|
|
* These values configure the required pins to drive the CC1200
|
|
* None of the following pins are exposed to any connector, kept for internal
|
|
* use only
|
|
* @{
|
|
*/
|
|
#define CC1200_SPI_INSTANCE 0
|
|
#define CC1200_SPI_SCLK_PORT SPI0_CLK_PORT
|
|
#define CC1200_SPI_SCLK_PIN SPI0_CLK_PIN
|
|
#define CC1200_SPI_MOSI_PORT SPI0_TX_PORT
|
|
#define CC1200_SPI_MOSI_PIN SPI0_TX_PIN
|
|
#define CC1200_SPI_MISO_PORT SPI0_RX_PORT
|
|
#define CC1200_SPI_MISO_PIN SPI0_RX_PIN
|
|
#define CC1200_SPI_CSN_PORT GPIO_B_NUM
|
|
#define CC1200_SPI_CSN_PIN 5
|
|
#define CC1200_GDO0_PORT GPIO_B_NUM
|
|
#define CC1200_GDO0_PIN 4
|
|
#define CC1200_GDO2_PORT GPIO_B_NUM
|
|
#define CC1200_GDO2_PIN 0
|
|
#define CC1200_RESET_PORT GPIO_C_NUM
|
|
#define CC1200_RESET_PIN 7
|
|
#define CC1200_GPIOx_VECTOR GPIO_B_IRQn
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Ethernet ENC28J60 configuration
|
|
*
|
|
* These values configure the required pins to drive an external Ethernet
|
|
* module. The implementation can be SPI or GPIO-based, for the first the SPI1
|
|
* controller should be used
|
|
* @{
|
|
*/
|
|
#define ETH_SPI_INSTANCE 1
|
|
#define ETH_SPI_CLK_PORT SPI1_CLK_PORT
|
|
#define ETH_SPI_CLK_PIN SPI1_CLK_PIN
|
|
#define ETH_SPI_MOSI_PORT SPI1_TX_PORT
|
|
#define ETH_SPI_MOSI_PIN SPI1_TX_PIN
|
|
#define ETH_SPI_MISO_PORT SPI1_RX_PORT
|
|
#define ETH_SPI_MISO_PIN SPI1_RX_PIN
|
|
#define ETH_SPI_CSN_PORT GPIO_A_NUM
|
|
#define ETH_SPI_CSN_PIN 7
|
|
#define ETH_INT_PORT GPIO_D_NUM
|
|
#define ETH_INT_PIN 0
|
|
#define ETH_RESET_PORT GPIO_D_NUM
|
|
#define ETH_RESET_PIN 1
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name On-board external WDT
|
|
* The Orion Ethernet Router has an external WDT and battery monitor, which
|
|
* adds more robustness and prevents the mote to run wild if any unexpected
|
|
* problem shows-up.
|
|
* The external WDT requires a short pulse (<1ms) to be sent before a 2-second
|
|
* period. The battery monitor keeps the device in Reset if the voltage input
|
|
* is lower than 2.5V.
|
|
* @{
|
|
*/
|
|
#define EXT_WDT_PORT GPIO_D_NUM
|
|
#define EXT_WDT_PIN 5
|
|
/** @} */
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \name Device string used on startup
|
|
* @{
|
|
*/
|
|
#define BOARD_STRING "Zolertia Orion Ethernet Router"
|
|
/** @} */
|
|
|
|
#endif /* BOARD_H_ */
|
|
|
|
/**
|
|
* @}
|
|
* @}
|
|
*/
|
|
|