osd-contiki/platform/micaz/contiki-conf.h
2009-09-08 08:59:29 +00:00

220 lines
7 KiB
C

/*
* Copyright (c) 2009, University of Colombo School of Computing
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the Institute nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* This file is part of the Contiki operating system.
*
* @(#)$$
*/
/**
* \file
* Configuration for MICAz platform.
*
* \author
* Kasun Hewage <kasun.ch@gmail.com>
*/
#ifndef __CONTIKI_CONF_H__
#define __CONTIKI_CONF_H__
#define HAVE_STDINT_H
#include "avrdef.h"
/*
* MCU and clock rate.
* MICAZ runs on 7.3728 MHz clock.
*/
#define MCU_MHZ 7
#define PLATFORM PLATFORM_AVR
/* Clock ticks per second */
#define CLOCK_CONF_SECOND 128
/* COM port to be used for SLIP connection */
#define SLIP_PORT RS232_PORT_0
/* Pre-allocated memory for loadable modules heap space (in bytes)*/
#define MMEM_CONF_SIZE 256
/* Use the following address for code received via the codeprop
* facility
*/
#define EEPROMFS_ADDR_CODEPROP 0x8000
#define TIMESYNCH_CONF_ENABLED 1
#define CC2420_CONF_TIMESTAMPS 1
#define WITH_NULLMAC 0
#define CCIF
#define CLIF
#ifdef WITH_UIP6
#define RIMEADDR_CONF_SIZE 8
#define UIP_CONF_LL_802154 1
#define UIP_CONF_LLH_LEN 0
#define UIP_CONF_IPV6 1
#define UIP_CONF_IPV6_QUEUE_PKT 1
#define UIP_CONF_IPV6_CHECKS 1
#define UIP_CONF_IPV6_REASSEMBLY 0
#define UIP_CONF_NETIF_MAX_ADDRESSES 3
#define UIP_CONF_ND6_MAX_PREFIXES 3
#define UIP_CONF_ND6_MAX_NEIGHBORS 4
#define UIP_CONF_ND6_MAX_DEFROUTERS 2
#define UIP_CONF_IP_FORWARD 0
#define SICSLOWPAN_CONF_COMPRESSION_IPV6 0
#define SICSLOWPAN_CONF_COMPRESSION_HC1 1
#define SICSLOWPAN_CONF_COMPRESSION_HC01 2
#define SICSLOWPAN_CONF_COMPRESSION SICS_LOWPAN_CONF_COMPRESSION_HC1
#define SICSLOWPAN_CONF_FRAG 0
#define SICSLOWPAN_CONF_CONVENTIONAL_MAC 1
#else
#define UIP_CONF_IP_FORWARD 1
#endif /* WITH_UIP6 */
#define UIP_CONF_ICMP_DEST_UNREACH 1
#define UIP_CONF_DHCP_LIGHT
#define UIP_CONF_LLH_LEN 0
#define UIP_CONF_BUFFER_SIZE 110
#define UIP_CONF_RECEIVE_WINDOW (UIP_CONF_BUFFER_SIZE - 40)
#define UIP_CONF_MAX_CONNECTIONS 4
#define UIP_CONF_MAX_LISTENPORTS 8
#define UIP_CONF_UDP_CONNS 12
#define UIP_CONF_FWCACHE_SIZE 30
#define UIP_CONF_BROADCAST 1
#define UIP_ARCH_IPCHKSUM 1
#define UIP_CONF_UDP_CHECKSUMS 1
#define UIP_CONF_PINGADDRCONF 0
#define UIP_CONF_LOGGING 0
#define UIP_CONF_TCP_SPLIT 0
/* LEDs ports. */
#define LEDS_PxDIR DDRA // port direction register
#define LEDS_PxOUT PORTA // port register
#define LEDS_CONF_RED 0x04 //red led
#define LEDS_CONF_GREEN 0x02 // green led
#define LEDS_CONF_YELLOW 0x01 // yellow led
/*
* SPI bus configuration for the MicaZ.
*/
/* SPI input/output registers. */
#define SPI_TXBUF SPDR
#define SPI_RXBUF SPDR
#define BV(bitno) _BV(bitno)
#define SPI_WAITFOREOTx() do { while (!(SPSR & BV(SPIF))); } while (0)
#define SPI_WAITFOREORx() do { while (!(SPSR & BV(SPIF))); } while (0)
#define SCK 1 /* - Output: SPI Serial Clock (SCLK) - ATMEGA128 PORTB, PIN1 */
#define MOSI 2 /* - Output: SPI Master out - slave in (MOSI) - ATMEGA128 PORTB, PIN2 */
#define MISO 3 /* - Input: SPI Master in - slave out (MISO) - ATMEGA128 PORTB, PIN3 */
/*
* SPI bus - CC2420 pin configuration.
*/
#define FIFO_P 6 /* - Input: FIFOP from CC2420 - ATMEGA128 PORTE, PIN6 */
#define FIFO 7 /* - Input: FIFO from CC2420 - ATMEGA128 PORTB, PIN7 */
#define CCA 6 /* - Input: CCA from CC2420 - ATMEGA128 PORTD, PIN6 */
#define SFD 4 /* - Input: SFD from CC2420 - ATMEGA128 PORTD, PIN4 */
#define CSN 0 /* - Output: SPI Chip Select (CS_N) - ATMEGA128 PORTB, PIN0 */
#define VREG_EN 5 /* - Output: VREG_EN to CC2420 - ATMEGA128 PORTA, PIN5 */
#define RESET_N 6 /* - Output: RESET_N to CC2420 - ATMEGA128 PORTA, PIN6 */
/* Pin status. */
#define FIFO_IS_1 (!!(PINB & BV(FIFO)))
#define CCA_IS_1 (!!(PIND & BV(CCA) ))
#define RESET_IS_1 (!!(PINA & BV(RESET_N)))
#define VREG_IS_1 (!!(PINA & BV(VREG_EN)))
#define FIFOP_IS_1 (!!(PINE & BV(FIFO_P)))
#define SFD_IS_1 (!!(PIND & BV(SFD)))
/* The CC2420 reset pin. */
#define SET_RESET_INACTIVE() ( PORTA |= BV(RESET_N) )
#define SET_RESET_ACTIVE() ( PORTA &= ~BV(RESET_N) )
/* CC2420 voltage regulator enable pin. */
#define SET_VREG_ACTIVE() ( PORTA |= BV(VREG_EN) )
#define SET_VREG_INACTIVE() ( PORTA &= ~BV(VREG_EN) )
/* CC2420 rising edge trigger for external interrupt 6 (FIFOP).
* Enable the external interrupt request for INT6.
* See Atmega128 datasheet about EICRB Register
*/
#define FIFOP_INT_INIT() do {\
EICRB |= 0x30; \
CLEAR_FIFOP_INT(); \
} while (0)
/* FIFOP on external interrupt 6. */
#define ENABLE_FIFOP_INT() do { EIMSK |= 0x40; } while (0)
#define DISABLE_FIFOP_INT() do { EIMSK &= ~0x40; } while (0)
#define CLEAR_FIFOP_INT() do { EIFR = 0x40; } while (0)
/* Enables/disables CC2420 access to the SPI bus (not the bus).
*
* These guys should really be renamed but are compatible with the
* original Chipcon naming.
*
* SPI_CC2420_ENABLE/SPI_CC2420_DISABLE???
* CC2420_ENABLE_SPI/CC2420_DISABLE_SPI???
*/
#define SPI_ENABLE() ( PORTB &= ~BV(CSN) ) /* ENABLE CSn (active low) */
#define SPI_DISABLE() ( PORTB |= BV(CSN) ) /* DISABLE CSn (active low) */
typedef unsigned short clock_time_t;
typedef unsigned short uip_stats_t;
typedef unsigned long off_t;
void clock_delay(unsigned int us2);
void clock_wait(int ms10);
void clock_set_seconds(unsigned long s);
unsigned long clock_seconds(void);
#endif /* __CONTIKI_CONF_H__ */