97 lines
4.2 KiB
Markdown
97 lines
4.2 KiB
Markdown
sensniff Contiki Project
|
|
========================
|
|
This example can be used to create an IEEE 802.15.4 wireless sniffer firmware,
|
|
meant to be used in parallel with
|
|
[sensniff](https://github.com/g-oikonomou/sensniff).
|
|
|
|
Running
|
|
=======
|
|
* Build this example and program your device
|
|
* Connect your device to a host
|
|
* Run sensniff on your host
|
|
* Fire up wireshark and enjoy.
|
|
|
|
You can run sensniff manually, or you can simply run `make sniff` from within
|
|
this directory. If you choose the latter option, you may have to specify the
|
|
port where you device is connected by using the PORT variable. For example, if
|
|
your device is connected to `/dev/ttyUSB1` then you should run
|
|
`make PORT=/dev/ttyUSB1 sniff`.
|
|
|
|
Make sure your device's UART baud rate matches the `-b` argument passed to
|
|
sensniff. I strongly recommend using at least 460800. This comment does not
|
|
apply if your device is using native USB.
|
|
|
|
Subsequently, make absolutely certain that your device is tuned to the same RF
|
|
channel as the network you are trying to sniff. You can change sniffing channel
|
|
through sensniff's text interface.
|
|
|
|
More details in sensniff's README.
|
|
|
|
Adding support for more platforms
|
|
=================================
|
|
Firstly, this example will try to turn off frame filtering and automatic h/w
|
|
ACKs by calling `NETSTACK_RADIO.set_value(RADIO_PARAM_RX_MODE, 0)`. If your
|
|
radio does not support this, then implementing this is your first step towards
|
|
running this example on your board.
|
|
|
|
Secondly, in order to be able to switch channels and retrieve current/min/max
|
|
RF channel supported from sensniff's text interface, your device's radio driver
|
|
must also support:
|
|
|
|
NETSTACK_RADIO.get_value(RADIO_PARAM_CHANNEL, ...)
|
|
NETSTACK_RADIO.set_value(RADIO_PARAM_CHANNEL, ...)
|
|
NETSTACK_RADIO.get_value(RADIO_CONST_CHANNEL_MIN, ...)
|
|
NETSTACK_RADIO.get_value(RADIO_CONST_CHANNEL_MAX, ...)
|
|
|
|
The following radios have been tested:
|
|
|
|
* CC13xx/CC26xx in PROP and IEEE modes
|
|
* CC2538
|
|
* CC2530/CC2531
|
|
* CC1200
|
|
* RF233
|
|
|
|
Once you have the radio sorted out, you also need to configure character I/O.
|
|
The firmware captures wireless frames and streams them over a serial line to
|
|
the host where your device is connected. This can be achieved over UART or over
|
|
CDC-ACM. The example makes zero assumptions about your hardware's capability,
|
|
you have to configure thnigs explicitly.
|
|
|
|
* Firstly, create a directory named the same as your platform. Crate a header
|
|
file therein called `target-conf.h`. This will get included automatically.
|
|
* Then look at the header files under `pool`, perhaps your device's CPU is
|
|
already supported. If that's the case, then within your `target-conf.h` you
|
|
simply need to add a line like this:
|
|
|
|
#define SENSNIFF_IO_DRIVER_H "pool/cc2538-io.h"
|
|
|
|
choosing the header that corresponds to your device's CPU. Just look for any of
|
|
the platforms already supported to see how you can configure things in a more
|
|
fine-grained fashion (e.g. to select UART instance, switch between UART/USB
|
|
etc).
|
|
|
|
* If your CPU is not already supported, then you need to create an additional
|
|
header file. In that header file, you will need to define the following three:
|
|
|
|
#define sensniff_io_byte_out() <driver function that prints bytes>
|
|
#define sensniff_io_flush() <for buffered I/O. Can be empty>
|
|
#define sensniff_io_set_input() <driver function that sets an input callback>
|
|
|
|
Those should map to functions implemented by your device's peripheral driver,
|
|
e.g. your UART driver. `_byte_out()` and `set_input()` are required, but
|
|
`_flush()` is optional and is only really helpful in case of drivers/hardware
|
|
that support buffered I/O (as is the case for some Contiki's USB drivers). Once
|
|
you have provided those defines, then simple go back to your `target-conf.h`
|
|
and:
|
|
|
|
#define SENSNIFF_IO_DRIVER_H "header-with-my-own-defines.h"
|
|
|
|
* The build system will also try to include `platform/Makefile.platform`. You
|
|
can create this Makefile if you want to extend the build system e.g. by adding
|
|
source files to the build, or by specifying Make variables. A common reason why
|
|
you may wish to do so would be to specify your device's baudrate. In doing so,
|
|
`make sniff` will pass the correct value as the argument to `-b`. You do not
|
|
have to create this file if you don't need to do so.
|
|
|
|
That should be it!
|
|
|