73774def6b
This patch adds a simple non-driver protection domain sample to serve as an example for defining other non-driver protection domains. It simply performs a ping-pong test of protection domain switching latency during boot, including optional accesses to a private metadata region, and prints out the results.
111 lines
4 KiB
Markdown
111 lines
4 KiB
Markdown
Galileo Specific Examples
|
|
=========================
|
|
|
|
This directory contains galileo-specific example applications to illustrate
|
|
how to use galileo APIs.
|
|
|
|
In order to build a application, you should set the EXAMPLE environment
|
|
variable to the name of the application you want to build. For instance, if
|
|
you want to build gpio-output application, run the following command:
|
|
|
|
```
|
|
$ make TARGET=galileo EXAMPLE=gpio-output
|
|
```
|
|
|
|
The corresponding EXAMPLE variable setting for each application is
|
|
listed to the right of its heading.
|
|
|
|
GPIO
|
|
----
|
|
|
|
### GPIO Output (EXAMPLE=gpio-output)
|
|
|
|
This application shows how to use the GPIO driver APIs to manipulate output
|
|
pins. This application sets the GPIO 5 pin as output pin and toggles its
|
|
state at every half second.
|
|
|
|
For a visual effect, you should wire shield pin IO2 to a led in a protoboard.
|
|
Once the application is running, you should see a blinking LED.
|
|
|
|
### GPIO Input (EXAMPLE=gpio-input)
|
|
|
|
This application shows how to use the GPIO driver APIs to manipulate
|
|
input pins. This application uses default galileo pinmux
|
|
initialization and sets the GPIO 5 (shield pin IO2) as output pin and
|
|
GPIO 6 (shield pin IO3) as input. A jumper should be used to connect
|
|
the two pins. The application toggles the output pin state at every
|
|
half second and checks the value on input pin.
|
|
|
|
### GPIO Interrupt (EXAMPLE=gpio-interrupt)
|
|
|
|
This application shows how to use the GPIO driver APIs to manipulate
|
|
interrupt pins. This application uses default galileo pinmux
|
|
initialization and sets the GPIO 5 (shield pin IO2) as output pin and
|
|
GPIO 6 (shield pin IO3) as interrupt. A jumper should be used to
|
|
connect the two pins. It toggles the output pin stat at every half
|
|
second in order to emulate an interrupt. This triggers an interrupt
|
|
and the application callback is called. You can confirm that though
|
|
the UART output.
|
|
|
|
I2C
|
|
---
|
|
|
|
### I2C LSM9DS0 (EXAMPLE=i2c-LSM9DS0)
|
|
|
|
This application shows how to use I2C driver APIs to configure I2C
|
|
Master controller and communicate with an LSM9DS0 sensor if one has
|
|
been connected as described below. At every 5 seconds, the application
|
|
reads the "who am I" register from gyroscope sensor and prints if the
|
|
register value matches the expected value described in the spec [1].
|
|
|
|
According to the sensor spec, to read the value in "who am I" register, we
|
|
should first perform an i2c write operation to select the register we want
|
|
to read from and then we perform the i2c read operation to actually read
|
|
the register contents.
|
|
|
|
The wiring setup is as follows (left column from Galileo and right column from LSM9DS0):
|
|
- 3.3v and Vin
|
|
- GND and GND
|
|
- GND and SDOG
|
|
- 3.3v and CSG
|
|
- SDA and SDA
|
|
- SCL and SCL
|
|
|
|
### I2C Callbacks (EXAMPLE=i2c-callbacks)
|
|
|
|
This application is very similar to the previous one in that it also
|
|
shows how to use I2C callback functionality, but it can be run without
|
|
attaching any additional sensors to the platform since it simply
|
|
communicates with a built-in PWM controller.
|
|
|
|
Every five seconds, the application reads the current value of the
|
|
MODE1 register, which should have previously been initialized to the
|
|
value 0x20. The test verifies that this expected value is returned by
|
|
the read.
|
|
|
|
Isolated Memory Regions
|
|
-----------------------
|
|
|
|
### Print IMR info (EXAMPLE=print-imr)
|
|
|
|
This application prints out information about the configuration of the
|
|
Intel Quark X1000 SoC Isolated Memory Regions (IMRs), the Host System
|
|
Management Mode Controls register, and the Host Memory I/O Boundary
|
|
register.
|
|
|
|
Protection Domains
|
|
------------------
|
|
|
|
### Protection Domain Switch Latency (EXAMPLE=prot-domain-switch-latency)
|
|
|
|
This application measures and prints the average latency of repeatedly
|
|
switching from one protection domain to another and back, in ping-pong
|
|
fashion. It can optionally perform memory accesses to metadata
|
|
associated with the destination protection domain. This feature can
|
|
be enabled by specifying SAMPLE_METADATA=1 on the build command line.
|
|
|
|
References
|
|
----------
|
|
|
|
[1] http://www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/DM00087365.pdf
|
|
|