254 lines
8.3 KiB
C
254 lines
8.3 KiB
C
/*
|
|
* Copyright (c) 2015, Texas Instruments Incorporated - http://www.ti.com/
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "driverlib/rf_mailbox.h"
|
|
#include "driverlib/rf_common_cmd.h"
|
|
#include "driverlib/rf_prop_cmd.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
/* Overrides for CMD_PROP_RADIO_DIV_SETUP */
|
|
static uint32_t overrides[] =
|
|
{
|
|
/*
|
|
* override_use_patch_prop_genfsk.xml
|
|
* PHY: Use MCE ROM bank 4, RFE RAM patch
|
|
*/
|
|
MCE_RFE_OVERRIDE(0, 4, 0, 1, 0, 0),
|
|
/*
|
|
* override_synth_prop_863_930_div5.xml
|
|
* Synth: Set recommended RTRIM to 7
|
|
*/
|
|
HW_REG_OVERRIDE(0x4038, 0x0037),
|
|
/* Synth: Set Fref to 4 MHz */
|
|
(uint32_t)0x000684A3,
|
|
/* Synth: Configure fine calibration setting */
|
|
HW_REG_OVERRIDE(0x4020, 0x7F00),
|
|
/* Synth: Configure fine calibration setting */
|
|
HW_REG_OVERRIDE(0x4064, 0x0040),
|
|
/* Synth: Configure fine calibration setting */
|
|
(uint32_t)0xB1070503,
|
|
/* Synth: Configure fine calibration setting */
|
|
(uint32_t)0x05330523,
|
|
/* Synth: Set loop bandwidth after lock to 20 kHz */
|
|
(uint32_t)0x0A480583,
|
|
/* Synth: Set loop bandwidth after lock to 20 kHz */
|
|
(uint32_t)0x7AB80603,
|
|
/*
|
|
* Synth: Configure VCO LDO
|
|
* (in ADI1, set VCOLDOCFG=0x9F to use voltage input reference)
|
|
*/
|
|
ADI_REG_OVERRIDE(1, 4, 0x9F),
|
|
/* Synth: Configure synth LDO (in ADI1, set SLDOCTL0.COMP_CAP=1) */
|
|
ADI_HALFREG_OVERRIDE(1, 7, 0x4, 0x4),
|
|
/* Synth: Use 24 MHz XOSC as synth clock, enable extra PLL filtering */
|
|
(uint32_t)0x02010403,
|
|
/* Synth: Configure extra PLL filtering */
|
|
(uint32_t)0x00108463,
|
|
/* Synth: Increase synth programming timeout (0x04B0 RAT ticks = 300 us) */
|
|
(uint32_t)0x04B00243,
|
|
/*
|
|
* override_phy_rx_aaf_bw_0xd.xml
|
|
* Rx: Set anti-aliasing filter bandwidth to 0xD
|
|
* (in ADI0, set IFAMPCTL3[7:4]=0xD)
|
|
*/
|
|
ADI_HALFREG_OVERRIDE(0, 61, 0xF, 0xD),
|
|
/*
|
|
* override_phy_gfsk_rx.xml
|
|
* Rx: Set LNA bias current trim offset to 3
|
|
*/
|
|
(uint32_t)0x00038883,
|
|
/* Rx: Freeze RSSI on sync found event */
|
|
HW_REG_OVERRIDE(0x6084, 0x35F1),
|
|
/*
|
|
* override_phy_gfsk_pa_ramp_agc_reflevel_0x1a.xml
|
|
* Tx: Enable PA ramping (0x41). Rx: Set AGC reference level to 0x1A.
|
|
*/
|
|
HW_REG_OVERRIDE(0x6088, 0x411A),
|
|
/* Tx: Configure PA ramping setting */
|
|
HW_REG_OVERRIDE(0x608C, 0x8213),
|
|
/*
|
|
* override_phy_rx_rssi_offset_5db.xml
|
|
* Rx: Set RSSI offset to adjust reported RSSI by +5 dB
|
|
*/
|
|
(uint32_t)0x00FB88A3,
|
|
/*
|
|
* TX power override
|
|
* Tx: Set PA trim to max (in ADI0, set PACTL0=0xF8)
|
|
*/
|
|
ADI_REG_OVERRIDE(0, 12, 0xF8),
|
|
|
|
/* Overrides for CRC16 functionality */
|
|
(uint32_t)0x943,
|
|
(uint32_t)0x963,
|
|
|
|
(uint32_t)0xFFFFFFFF,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* CMD_PROP_RADIO_DIV_SETUP */
|
|
rfc_CMD_PROP_RADIO_DIV_SETUP_t smartrf_settings_cmd_prop_radio_div_setup =
|
|
{
|
|
.commandNo = 0x3807,
|
|
.status = 0x0000,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = 0x0,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = 0x1,
|
|
.condition.nSkip = 0x0,
|
|
.modulation.modType = 0x1,
|
|
.modulation.deviation = 0x64,
|
|
.symbolRate.preScale = 0xf,
|
|
.symbolRate.rateWord = 0x8000,
|
|
.rxBw = 0x24,
|
|
.preamConf.nPreamBytes = 0x3,
|
|
.preamConf.preamMode = 0x0,
|
|
.formatConf.nSwBits = 0x18,
|
|
.formatConf.bBitReversal = 0x0,
|
|
.formatConf.bMsbFirst = 0x1,
|
|
.formatConf.fecMode = 0x0,
|
|
|
|
/* 7: .4g mode with dynamic whitening and CRC choice */
|
|
.formatConf.whitenMode = 0x7,
|
|
.config.frontEndMode = 0x0, /* Differential mode */
|
|
.config.biasMode = 0x1, /* External bias*/
|
|
.config.analogCfgMode = 0x0,
|
|
.config.bNoFsPowerUp = 0x0,
|
|
.txPower = 0x00, /* Driver sets correct value */
|
|
.pRegOverride = overrides,
|
|
.intFreq = 0x8000,
|
|
.centerFreq = 868,
|
|
.loDivider = 0x05,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* CMD_FS */
|
|
rfc_CMD_FS_t smartrf_settings_cmd_fs =
|
|
{
|
|
.commandNo = 0x0803,
|
|
.status = 0x0000,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = 0x0,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = 0x1,
|
|
.condition.nSkip = 0x0,
|
|
.frequency = 868,
|
|
.fractFreq = 0x0000,
|
|
.synthConf.bTxMode = 0x0,
|
|
.synthConf.refFreq = 0x0,
|
|
.__dummy0 = 0x00,
|
|
.__dummy1 = 0x00,
|
|
.__dummy2 = 0x00,
|
|
.__dummy3 = 0x0000,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* CMD_PROP_TX_ADV */
|
|
rfc_CMD_PROP_TX_ADV_t smartrf_settings_cmd_prop_tx_adv =
|
|
{
|
|
.commandNo = 0x3803,
|
|
.status = 0x0000,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = 0x0,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = 0x1,
|
|
.condition.nSkip = 0x0,
|
|
.pktConf.bFsOff = 0x0,
|
|
.pktConf.bUseCrc = 0x1,
|
|
.pktConf.bCrcIncSw = 0x0, /* .4g mode */
|
|
.pktConf.bCrcIncHdr = 0x0, /* .4g mode */
|
|
.numHdrBits = 0x10 /* 16: .4g mode */,
|
|
.pktLen = 0x0000,
|
|
.startConf.bExtTxTrig = 0x0,
|
|
.startConf.inputMode = 0x0,
|
|
.startConf.source = 0x0,
|
|
.preTrigger.triggerType = TRIG_REL_START,
|
|
.preTrigger.bEnaCmd = 0x0,
|
|
.preTrigger.triggerNo = 0x0,
|
|
.preTrigger.pastTrig = 0x1,
|
|
.preTime = 0x00000000,
|
|
.syncWord = 0x0055904e,
|
|
.pPkt = 0,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|
|
/* CMD_PROP_RX_ADV */
|
|
rfc_CMD_PROP_RX_ADV_t smartrf_settings_cmd_prop_rx_adv =
|
|
{
|
|
.commandNo = 0x3804,
|
|
.status = 0x0000,
|
|
.pNextOp = 0,
|
|
.startTime = 0x00000000,
|
|
.startTrigger.triggerType = 0x0,
|
|
.startTrigger.bEnaCmd = 0x0,
|
|
.startTrigger.triggerNo = 0x0,
|
|
.startTrigger.pastTrig = 0x0,
|
|
.condition.rule = 0x1,
|
|
.condition.nSkip = 0x0,
|
|
.pktConf.bFsOff = 0x0,
|
|
.pktConf.bRepeatOk = 0x1,
|
|
.pktConf.bRepeatNok = 0x1,
|
|
.pktConf.bUseCrc = 0x1,
|
|
.pktConf.bCrcIncSw = 0x0, /* .4g mode */
|
|
.pktConf.bCrcIncHdr = 0x0, /* .4g mode */
|
|
.pktConf.endType = 0x0,
|
|
.pktConf.filterOp = 0x1,
|
|
.rxConf.bAutoFlushIgnored = 0x1,
|
|
.rxConf.bAutoFlushCrcErr = 0x1,
|
|
.rxConf.bIncludeHdr = 0x0,
|
|
.rxConf.bIncludeCrc = 0x0,
|
|
.rxConf.bAppendRssi = 0x1,
|
|
.rxConf.bAppendTimestamp = 0x0,
|
|
.rxConf.bAppendStatus = 0x1,
|
|
.syncWord0 = 0x0055904e,
|
|
.syncWord1 = 0x00000000,
|
|
.maxPktLen = 0x0000, /* To be populated by the driver. */
|
|
.hdrConf.numHdrBits = 0x10, /* 16: .4g mode */
|
|
.hdrConf.lenPos = 0x0, /* .4g mode */
|
|
.hdrConf.numLenBits = 0x0B, /* 11 = 0x0B .4g mode */
|
|
.addrConf.addrType = 0x0,
|
|
.addrConf.addrSize = 0x0,
|
|
.addrConf.addrPos = 0x0,
|
|
.addrConf.numAddr = 0x0,
|
|
.lenOffset = -4, /* .4g mode */
|
|
.endTrigger.triggerType = TRIG_NEVER,
|
|
.endTrigger.bEnaCmd = 0x0,
|
|
.endTrigger.triggerNo = 0x0,
|
|
.endTrigger.pastTrig = 0x0,
|
|
.endTime = 0x00000000,
|
|
.pAddr = 0,
|
|
.pQueue = 0,
|
|
.pOutput = 0,
|
|
};
|
|
/*---------------------------------------------------------------------------*/
|