nvt-se
|
e9d279620f
|
more protection against interrupts that might spoil SPI sequences.
made coding style more like that of contiki.
|
2009-05-26 12:15:46 +00:00 |
|
nvt-se
|
09a1c115fe
|
initial test port of Coffee for the MSB-430 platform.
|
2009-05-25 14:14:32 +00:00 |
|
nvt-se
|
8f7f7fb896
|
enabled random I/O in the SD driver.
|
2009-05-25 14:13:47 +00:00 |
|
nvt-se
|
da91d87ae6
|
switch of interrupts while writing and reading to the SPI. avoids
desynchronization problems.
|
2009-05-25 13:19:04 +00:00 |
|
fros4943
|
faec70dee0
|
test app update: print sensor type
|
2009-05-19 17:54:08 +00:00 |
|
fros4943
|
d54176205c
|
decreased default elfloader memory usage for sky platform
|
2009-05-18 10:32:56 +00:00 |
|
nvt-se
|
bcc5084564
|
removed delay because while loop waits until completion anyway.
|
2009-05-15 13:54:08 +00:00 |
|
nvt-se
|
f9b35795c7
|
minor refactoring.
|
2009-05-14 12:18:49 +00:00 |
|
adamdunkels
|
bc6c9410cc
|
Print out the gateway's IP address more prominently
|
2009-05-12 17:32:49 +00:00 |
|
adamdunkels
|
00890caca8
|
Make sure that symbols.c is included in every native cpu build, not just the native target
|
2009-05-12 17:23:23 +00:00 |
|
nvt-se
|
74e9bc8789
|
Added flash reads and writes to energest.
|
2009-05-11 15:26:24 +00:00 |
|
adamdunkels
|
900480959b
|
Increased the default number of queue buffers: there usually is plenty of RAM left, so we should be able to afford it
|
2009-05-10 21:15:16 +00:00 |
|
joxe
|
6a7bc4c3a5
|
added mcu-chip temperature to accelerometer sensor - value 3
|
2009-05-08 16:03:50 +00:00 |
|
adamdunkels
|
6fcca2d545
|
Initialize ctimer, add IPv6 address configuration for the aaaa prefix
|
2009-04-29 11:49:27 +00:00 |
|
adamdunkels
|
e6215712ca
|
When a node is configured as an IP gateway, we switch off the power-saving MAC protocolto improve performance and to avoid problems with the serial communication that X-MACs use of rtimers can cause
|
2009-04-29 11:46:20 +00:00 |
|
adamdunkels
|
064f4488d4
|
Increase default CPU speed from 2.4576 MHz to 3.9 MHz. Communication works better, at a low power cost
|
2009-04-29 11:43:48 +00:00 |
|
adamdunkels
|
bbab7ba55c
|
When the tmote-bsl binary is found, program only one mote at once (parallel programming with tmote-bsl doesn't seem to work)
|
2009-04-29 11:42:56 +00:00 |
|
fros4943
|
9f299c277e
|
added experimental slip support for contiki motes
|
2009-04-23 09:15:51 +00:00 |
|
fros4943
|
9bd3d07510
|
implemented slip_arch_writeb() function
|
2009-04-23 09:02:06 +00:00 |
|
fros4943
|
b65014d1be
|
bugfix by Wolf-Bastian Pttner: check buffer size at incoming radio data
|
2009-04-16 14:38:41 +00:00 |
|
fros4943
|
bc6704079c
|
cc2420 checksums temporarily disabled, due to timing problems with the x-mac unicast optimization
|
2009-04-16 14:34:51 +00:00 |
|
adamdunkels
|
2e37fca49f
|
Check for tmote-bsl-linux binary under linux, and use it is available
|
2009-04-10 07:43:29 +00:00 |
|
adamdunkels
|
2545fd9069
|
Hack to make DS2411 ID useable as an Ethernet MAC address (remove multicast bit)
|
2009-04-10 00:40:08 +00:00 |
|
adamdunkels
|
3415ff26bd
|
Added CC2420 checksums to non-ipv6 packets. Set a conservative TCP MSS
|
2009-04-10 00:39:19 +00:00 |
|
nvt-se
|
172ffb74c7
|
fix compiler warnings. patch from Jesper Karlsson.
|
2009-04-08 14:56:00 +00:00 |
|
nifi
|
b41b79e3a9
|
Disable timestamp when using 802.15.4 frames (CC2420_CONF_TIMESTAMPS adds timestamp to radio packets).
|
2009-04-06 17:18:20 +00:00 |
|
nifi
|
900d8d8e17
|
changed to use HC01 compression for uip6
|
2009-04-06 16:01:11 +00:00 |
|
nifi
|
8b41f3a6a8
|
set rime addr size to 8 for uip6, restored clock resolution
|
2009-04-06 14:59:49 +00:00 |
|
nifi
|
76b7bf43d0
|
added setup for uip6 with 802.15.4 frames and routing using Rime
|
2009-04-06 14:12:58 +00:00 |
|
nifi
|
a36e529df1
|
added configuration for panid
|
2009-04-06 13:31:00 +00:00 |
|
nvt-se
|
f53560f6a5
|
enabled multihop routing, increased uip buffer size.
|
2009-04-06 13:23:14 +00:00 |
|
nifi
|
c1d490b6a7
|
added workaround for memcpy/memset bug in mspgcc
|
2009-04-06 13:07:37 +00:00 |
|
adamdunkels
|
58331e6802
|
Made tick resultion more fine-grained to support a shorter LPP listen time
|
2009-04-03 11:46:48 +00:00 |
|
fros4943
|
b730fb329d
|
changed upload rules due to problems on linux platforms
|
2009-04-02 11:15:30 +00:00 |
|
fros4943
|
3b3580e439
|
disabled writing IP addresses from inside COOJA, since the these should rather be determined by Contiki
|
2009-04-01 18:11:48 +00:00 |
|
fros4943
|
aa736322e1
|
removed unused uip/uaodv cooja comm stack. mesh-uip should be used instead
|
2009-04-01 17:17:55 +00:00 |
|
fros4943
|
3665422d8d
|
simplified cooja communication stacks initialization + added uipv6 stack
|
2009-04-01 13:50:12 +00:00 |
|
fros4943
|
6a99a82516
|
copied uipv6 configuration from native platform
|
2009-04-01 13:46:56 +00:00 |
|
fros4943
|
1c031504e5
|
no need to initialize serial line
|
2009-04-01 13:46:16 +00:00 |
|
fros4943
|
892bfb5678
|
moved radio-uip link functionality directly to comm stack sources
|
2009-04-01 13:45:41 +00:00 |
|
fros4943
|
eddd8350c5
|
renamed radio driver
|
2009-04-01 13:44:34 +00:00 |
|
fros4943
|
afed9bb2d0
|
icnlude packet radio by default
|
2009-04-01 13:39:54 +00:00 |
|
nifi
|
c6b15c289e
|
* show radio channel at startup
* only initialize timesynch when timesynch is enabled
|
2009-03-31 13:25:50 +00:00 |
|
nvt-se
|
e90149b7b4
|
avoid switching mode when tx or rx is active.
based on suggestions from Frederik Hermans and some code from Jesper Karlsson.
|
2009-03-30 14:07:34 +00:00 |
|
fros4943
|
5f1fda0406
|
removed unused variables + writing serial data in timeevent
|
2009-03-26 16:23:47 +00:00 |
|
fros4943
|
dda6de8438
|
+ clock stub functions
|
2009-03-26 16:22:36 +00:00 |
|
fros4943
|
ac22ad5081
|
changed the Makefile rules for uploading to sky-nodes.
the earlier approach caused problems sometimes, resulting in command succeeding without all nodes being reprogrammed
|
2009-03-26 13:29:44 +00:00 |
|
nvt-se
|
04bd414e1c
|
enabled LPP by default.
|
2009-03-26 12:51:55 +00:00 |
|
nvt-se
|
90b9b9bae3
|
configure LPP parameters with slightly longer listen time since the CC1020
driver switches from TX mode to RX mode rather slowly.
decreased CCA check timeout.
|
2009-03-26 12:47:12 +00:00 |
|
nvt-se
|
25cc327acc
|
avoid hanging in TX mode after CCA check failed.
minor memory savings.
|
2009-03-25 15:25:05 +00:00 |
|