Create a dedicated header file with all the definitions for the flash lock bit
page and customer configuration area. This avoids duplicating those definitions
in the startup-gcc.c files of all CC2538-based platforms, and this also allows
to easily manipulate the CCA from outside startup-gcc.c (e.g. for on-the-air
firmware update).
The definitions are now complete contrary to what was in startup-gcc.c:
- Definitions have been added to select the bootloader backdoor pin and active
level if enabled.
- Definitions have been added to access the page and debug lock bits. The debug
lock bit can be used to prevent someone from reading back a programmed
firmware through JTAG if the firmware binary image has to be confidential,
which should be combined with a disabled bootloader backdoor.
- The application entry point is now tied to the beginning of the .text section
instead of to the beginning of the flash. This allows projects using custom
linker scripts to place the application entry point anywhere in the flash,
which can be useful e.g. for on-the-air firmware update.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
SYS_CTRL_EMUOVR is already defined in sys-ctrl.h, so #include this header file
instead of redefining SYS_CTRL_EMUOVR in startup-gcc.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch adds the eeprom driver needed to access M24C64
eeprom which is on some mbxxx boards.
Signed-off-by: Maria Laura Stefanizzi <laura28582@gmail.com>
This patch add the I2C driver for mbxxx platform to communicate with
devices connected to the SC2 I2C bus.
Signed-off-by: Maria Laura Stefanizzi <laura28582@gmail.com>
As the comment in contiki-conf.h says, the automatic definition of
SLIP_ARCH_CONF_ENABLED works only if UIP_FALLBACK_INTERFACE is tied to SLIP. If
UIP_FALLBACK_INTERFACE is set to another interface, SLIP_ARCH_CONF_ENABLED is
still automatically set to 1, leading to unwanted SLIP_END characters from
dbg.c:putchar() being printed on the UART.
This change makes it possible to force the definition of SLIP_ARCH_CONF_ENABLED
(e.g. from project-conf.h), so that it can be disabled if UIP_FALLBACK_INTERFACE
is used with something else than SLIP.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Homogenize port and pin definitions naming:
- PERIPHERAL_FUNCTION_PORT for the port ID,
- PERIPHERAL_FUNCTION_PIN for the pin ID,
- PERIPHERAL_FUNCTION_PORT_BASE for the port base,
- PERIPHERAL_FUNCTION_PIN_MASK for the pin mask.
Define only PERIPHERAL_FUNCTION_PORT and PERIPHERAL_FUNCTION_PIN in board.h, and
deduce PERIPHERAL_FUNCTION_PORT_BASE and PERIPHERAL_FUNCTION_PIN_MASK in the
driver from the former definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
like /tools/mspsim.
This is a very simple modification that affects a very large number of files in Contiki: Cooja,
/platform/cooja, Collect-view, Coffe-manager, and Cooja simulation files (.csc).
I've gone through Contiki to update all references I could find. Nevertheless, this commit will likely
break external dependencies, like saved Cooja simulation files.
Use the GPIO accessor macros instead of copying raw register access code all
over the place. This is cleaner and less error prone.
This fixes the setting of the USB pull-up resistor that worked only by chance on
the CC2538DK because it is controlled by the pin 0 of the used GPIO port.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Some peripherals have their clocks automatically gated in PM1+ modes, so they
cannot operate. This new mechanism gives peripherals a way to prohibit PM1+
modes so that they can properly complete their current operations before
entering PM1+.
This mechanism is implemented with peripheral functions registered to the LPM
module. These functions return whether the associated peripheral permits or not
PM1+ modes. They are called by the LPM module each time PM1+ might be possible.
If any of the peripherals wants to block PM1+, then the system is only dropped
to PM0.
Partly from: George Oikonomou
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The CCA-threshold now defaults to -46 which give better simulation
results and typically also better experimental results.
This adjustment is also needed due to commit 0a13f99 in mspsim. As
promised in https://github.com/mspsim/mspsim/pull/18 it broke the
regression tests.
This uses the core/dev/spi.h header and implements the spi_init()
function and the various macros for SPI operation. ssi.h contains all of
the register locations and information.
This implementation is not very versatile, mostly because I don't how to
make it flexible in the contiki system. It supports pin muxing for the
four spi pins, but other than that picks sensible defaults.
The SPI macros (like SPI_READ()) are defined in
cpu/cc2538/spi-arch.h. In order to use the SPI driver, add the following
includes to your project:
#include "spi-arch.h
#include "dev/spi.h"
Since introduction of mDNS (f145c17039)
the resolver process initialization depends on the tcpip process
already being initialized (because of the call to udp_new()).
The CC2531 USB stick now identifies itself as a
'Texas Instruments CC2531 USB Dongle' and uses a
TI-assigmed VID:PID. The VID:PID is now configurable
in contiki- or project-conf.h
The sensinode platform does not support .upload and .serialdump
Their presence in the makefile has confused in the past confused
some users. This commit removes them
The commit also removes the $(OBJECTDIR)/%.rel: %.cS recipe which
is not used by either 8051 platform and is probably broken anyway,
since it has been unmaintained for years
Historically $(OBJECTDIR) was created when Makefile.include is read. A
consequence is that combining "clean" with "all" (or any other build
target) results in an error because the clean removes the object
directory that is required to exist when building dependencies.
Creating $(OBJECTDIR) on-demand ensures it is present when needed.
Removed creation of $(OBJECTDIR) on initial read, and added an order-only
dependency forcing its creation all Makefile* rules where the target is
explicitly or implicitly in $(OBJECTDIR).
The new Atari XL target allows cc65 programs to make use of
the shadow RAM. This allows to turn aon all features of the
web browser - and will allow for additional improvements to
come :-)
