95 lines
3.2 KiB
C
95 lines
3.2 KiB
C
/*
|
|
* Copyright (c) 2010, Loughborough University - Computer Science
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* This file is part of the Contiki operating system.
|
|
*/
|
|
|
|
/**
|
|
* \file
|
|
* Model-specific functions for Sensinode devices.
|
|
*
|
|
* Bankable
|
|
*
|
|
* \author
|
|
* George Oikonomou - <oikonomou@users.sourceforge.net>
|
|
*/
|
|
|
|
#include "dev/models.h"
|
|
#include "dev/uart1.h"
|
|
#include "dev/m25p16.h"
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
model_init()
|
|
{
|
|
#ifdef MODEL_N740
|
|
/*
|
|
* We want to prevent the dongle from controlling the state of the
|
|
* analog switch on the N740s.
|
|
*
|
|
* Set P0_3 as out and start with P0_3=0 (USB and Light selected)
|
|
*/
|
|
P0DIR |= 0x08; /* P0_3 out */
|
|
P0_3 = 0;
|
|
|
|
/* Init the serial-parallel chip for N740s. This will also 'init' LEDs */
|
|
n740_ser_par_init();
|
|
|
|
/* Put the Serial Flash in Deep Power mode */
|
|
n740_analog_deactivate();
|
|
|
|
#if M25P16_CONF_ON
|
|
m25p16_dp();
|
|
#endif /* SERIAL_FLASH_CONF_ON */
|
|
|
|
n740_ser_par_set(0);
|
|
#endif
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
model_uart_intr_en()
|
|
{
|
|
#ifdef MODEL_N740
|
|
/*
|
|
* Dirty, ugly hack for the N740 USART1 RX issue:
|
|
* When the USB is for whatever reason disabled (either disconnected or the
|
|
* analog switch has switched to the D-connector), RX starts flowing down
|
|
* pin 1.7 (and the line stays low), resulting in non-stop UART1_RX
|
|
* interrupts. So, we only acknowledge the interrupt when the line is
|
|
* high and the dongle is connected (thus we are on USB).
|
|
*
|
|
* For all other models, just turn the interrupt on
|
|
*
|
|
* Interrupts will only turn on if UART_ONE_CONF_WITH_INPUT is defined 1
|
|
*/
|
|
if(P1_7 == 1 && P0_3 == 0) {
|
|
UART1_RX_INT(1);
|
|
}
|
|
#else
|
|
UART1_RX_INT(1);
|
|
#endif
|
|
}
|