212 lines
6.2 KiB
C
212 lines
6.2 KiB
C
/*
|
|
* Copyright (c) 2010, Loughborough University - Computer Science
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* This file is part of the Contiki operating system.
|
|
*/
|
|
|
|
/**
|
|
* \file
|
|
* ADC sensor module for sensinode devices.
|
|
*
|
|
* This file respects configuration in contiki-conf.h. It also turns
|
|
* off features which are not present in the model that we are
|
|
* building for.
|
|
*
|
|
* \author
|
|
* George Oikonomou - <oikonomou@users.sourceforge.net>
|
|
*/
|
|
#include "dev/sensinode-sensors.h"
|
|
|
|
#if ADC_SENSOR_ON
|
|
SENSORS_SENSOR(adc_sensor, ADC_SENSOR, value, configure, status);
|
|
|
|
static uint8_t ready;
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
static int
|
|
value(int type)
|
|
{
|
|
uint16_t reading;
|
|
/*
|
|
* For single-shot AD conversions, we may only write to ADCCON3[3:0] once
|
|
* (This write triggers the conversion). We thus use the variable 'command'
|
|
* to store intermediate steps (reference, decimation rate, input channel)
|
|
*/
|
|
uint8_t command;
|
|
|
|
ADCCFG = 0; /* Enables/Disables Input Channel */
|
|
|
|
/* 1.25V ref, max decimation rate */
|
|
command = ADEDIV1 | ADEDIV0;
|
|
|
|
/* Clear the Interrupt Flag */
|
|
TCON_ADCIF = 0;
|
|
|
|
/* Depending on the desired reading, append the input bits to 'command' and
|
|
* enable the corresponding input channel in ADCCFG if necessary */
|
|
switch(type) {
|
|
#if TEMP_SENSOR_ON
|
|
case ADC_SENSOR_TYPE_TEMP:
|
|
command |= ADECH3 | ADECH2 | ADECH1;
|
|
break;
|
|
#endif
|
|
#if ACC_SENSOR_ON
|
|
case ADC_SENSOR_TYPE_ACC_X:
|
|
ADCCFG = ADC5EN;
|
|
command |= ADECH2 | ADECH0;
|
|
break;
|
|
case ADC_SENSOR_TYPE_ACC_Y:
|
|
ADCCFG = ADC6EN;
|
|
command |= ADECH2 | ADECH1;
|
|
break;
|
|
case ADC_SENSOR_TYPE_ACC_Z:
|
|
ADCCFG = ADC7EN;
|
|
command |= ADECH2 | ADECH1 | ADECH0;
|
|
break;
|
|
#endif
|
|
#if VDD_SENSOR_ON
|
|
case ADC_SENSOR_TYPE_VDD:
|
|
command |= ADECH3 | ADECH2 | ADECH1 | ADECH0;
|
|
break;
|
|
#endif
|
|
#if LIGHT_SENSOR_ON
|
|
case ADC_SENSOR_TYPE_LIGHT:
|
|
ADCCFG = ADC0EN;
|
|
break;
|
|
#endif
|
|
#if BATTERY_SENSOR_ON
|
|
case ADC_SENSOR_TYPE_BATTERY:
|
|
ADCCFG = ADC1EN;
|
|
command |= ADECH0 | ADEREF1; /* AVDD_SOC reference */
|
|
break;
|
|
#endif
|
|
default:
|
|
/* If the sensor is not present or disabled in conf, return -1 */
|
|
return -1;
|
|
}
|
|
|
|
/* Writing in bits 3:0 of ADCCON3 will trigger a single conversion */
|
|
ADCCON3 = command;
|
|
|
|
/*
|
|
* When the conversion is complete, the ADC interrupt flag is set. We don't
|
|
* use an ISR here, we just wait on the flag and clear it afterwards.
|
|
*/
|
|
while(!TCON_ADCIF);
|
|
|
|
/* Clear the Interrupt Flag */
|
|
TCON_ADCIF = 0;
|
|
|
|
reading = 0;
|
|
reading = ADCL;
|
|
reading |= (((uint8_t) ADCH) << 8);
|
|
/* 12-bit decimation rate: 4 LS bits are noise */
|
|
reading >>= 4;
|
|
|
|
return reading;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
static int
|
|
status(int type)
|
|
{
|
|
return ready;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* On N740 we can control Ill and Acc individually:
|
|
* ADC_VAL_OTHERS 0x01
|
|
* ADC_VAL_LIGHT_ON 0x04
|
|
* ADC_VAL_ACC_ON 0x08
|
|
* ADC_VAL_ACC_GSEL 0x10
|
|
*
|
|
* Return Value is always light | acc | acc_gsel
|
|
*
|
|
* SENSORS_ACTIVE:
|
|
* - 1: Activate everything, use default setting for ACC G-select
|
|
* - 0: Turn everything off
|
|
* - xyz: Mask with the defines above and act accordingly.
|
|
*
|
|
* SENSORS_READY:
|
|
* - Return Status (0: all off or a value based on the defines above)
|
|
*/
|
|
static int
|
|
configure(int type, int value)
|
|
{
|
|
#ifdef MODEL_N740
|
|
/*
|
|
* Read current state of the ser-par, ignoring current sensor settings
|
|
* Those will be set all over depending on VALUE
|
|
*/
|
|
uint8_t ser_par_val = n740_ser_par_get() & 0xF2;
|
|
#endif /* MODEL_N740 */
|
|
|
|
/* 'Others' are either compiled in or not. Can't be turned on/off */
|
|
ready = ADC_VAL_ALL;
|
|
|
|
switch(type) {
|
|
case SENSORS_HW_INIT:
|
|
case SENSORS_ACTIVE:
|
|
#ifdef MODEL_N740
|
|
if(value == ADC_VAL_ALL) {
|
|
value = ADC_VAL_ACC_ON | ADC_VAL_LIGHT_ON;
|
|
#if ACC_SENSOR_GSEL
|
|
value |= ADC_VAL_ACC_GSEL;
|
|
#endif /* ACC_SENSOR_GSEL */
|
|
}
|
|
#endif /* MODEL_N740 */
|
|
|
|
/* OK, Now value definitely specifies our bits, start masking
|
|
* We will refuse to turn things on if they are specified OFF in conf. */
|
|
#ifdef MODEL_N740
|
|
#if ACC_SENSOR_ON
|
|
if(value & ADC_VAL_ACC_ON) {
|
|
P0SEL |= 0x80 | 0x40 | 0x20;
|
|
ser_par_val |= N740_SER_PAR_ACC;
|
|
ready |= ADC_VAL_ACC_ON;
|
|
#if ACC_SENSOR_GSEL
|
|
if(value & ADC_VAL_ACC_GSEL) {
|
|
ser_par_val |= N740_SER_PAR_ACC_GSEL;
|
|
ready |= ADC_VAL_ACC_GSEL;
|
|
}
|
|
#endif /*ACC_SENSOR_GSEL */
|
|
}
|
|
#endif /* ACC_SENSOR_ON */
|
|
|
|
#if LIGHT_SENSOR_ON
|
|
if(value & ADC_VAL_LIGHT_ON) {
|
|
ser_par_val |= N740_SER_PAR_LIGHT;
|
|
ready |= ADC_VAL_LIGHT_ON;
|
|
}
|
|
#endif /* LIGHT_SENSOR_ON */
|
|
n740_ser_par_set(ser_par_val);
|
|
#endif /* MODEL_N740 */
|
|
}
|
|
return ready;
|
|
}
|
|
|
|
#endif /* ADC_SENSOR_ON */
|