157 lines
5 KiB
C
157 lines
5 KiB
C
/* This file has been prepared for Doxygen automatic documentation generation.*/
|
|
/*! \file conf_usb.h **********************************************************
|
|
*
|
|
* \brief
|
|
* This file contains the possible external configuration of the USB.
|
|
*
|
|
* \addtogroup usbstick
|
|
*
|
|
* \author
|
|
* Atmel Corporation: http://www.atmel.com \n
|
|
* Support email: avr@atmel.com
|
|
*
|
|
******************************************************************************/
|
|
/* Copyright (c) 2008 ATMEL Corporation
|
|
All rights reserved.
|
|
|
|
Redistribution and use in source and binary forms, with or without
|
|
modification, are permitted provided that the following conditions are met:
|
|
|
|
* Redistributions of source code must retain the above copyright
|
|
notice, this list of conditions and the following disclaimer.
|
|
* Redistributions in binary form must reproduce the above copyright
|
|
notice, this list of conditions and the following disclaimer in
|
|
the documentation and/or other materials provided with the
|
|
distribution.
|
|
* Neither the name of the copyright holders nor the names of
|
|
contributors may be used to endorse or promote products derived
|
|
from this software without specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
|
|
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#ifndef _CONF_USB_H_
|
|
#define _CONF_USB_H_
|
|
|
|
|
|
|
|
/**
|
|
\ingroup usbstick
|
|
\defgroup usbconf USB Configuration
|
|
@{
|
|
*/
|
|
|
|
|
|
// _________________ USB MODE CONFIGURATION ____________________________
|
|
//! @ingroup usbconf
|
|
//! @defgroup USB_op_mode USB operating modes configuration
|
|
//! defines to enable device or host usb operating modes
|
|
//! supported by the application
|
|
//! @{
|
|
|
|
//! @brief ENABLE to activate the host software library support
|
|
//!
|
|
//! Possible values ENABLE or DISABLE
|
|
#define USB_HOST_FEATURE DISABLED
|
|
|
|
//! @brief ENABLE to activate the device software library support
|
|
//!
|
|
//! Possible values ENABLE or DISABLE
|
|
#define USB_DEVICE_FEATURE ENABLED
|
|
|
|
//! @}
|
|
|
|
// _________________ USB REGULATOR CONFIGURATION _______________________
|
|
//! @ingroup usbconf
|
|
//! @defgroup USB_reg_mode USB regulator configuration
|
|
//! @{
|
|
|
|
//! @brief Enable the internal regulator for USB pads
|
|
//!
|
|
//! When the application voltage is lower than 3.5V, to optimize power consumption
|
|
//! the internal USB pads regulatr can be disabled.
|
|
#ifndef USE_USB_PADS_REGULATOR
|
|
#define USE_USB_PADS_REGULATOR ENABLE // Possible values ENABLE or DISABLE
|
|
#endif
|
|
//! @}
|
|
|
|
// _________________ DEVICE MODE CONFIGURATION __________________________
|
|
|
|
//! @ingroup usbconf
|
|
//! @defgroup USB_device_mode_cfg USB device operating mode configuration
|
|
//!
|
|
//! @{
|
|
|
|
/** USB RNDIS / Virtual com port setup **/
|
|
|
|
#ifndef CDC_ECM_USES_INTERRUPT_ENDPOINT
|
|
#define CDC_ECM_USES_INTERRUPT_ENDPOINT 0
|
|
#endif
|
|
|
|
#ifndef USB_ETH_EMULATE_WIFI
|
|
#define USB_ETH_EMULATE_WIFI 0
|
|
#endif
|
|
|
|
#define NB_ENDPOINTS 7 //! number of endpoints in the application including control endpoint
|
|
#define VCP_RX_EP 0x06
|
|
#define VCP_TX_EP 0x05
|
|
#define VCP_INT_EP 0x04
|
|
#define TX_EP 0x01
|
|
#define RX_EP 0x02
|
|
#define INT_EP 0x03
|
|
|
|
/** USB Mass Storage Setup **/
|
|
|
|
#define NB_ENDPOINTS_MS 3 //! number of endpoints in the application including control endpoint
|
|
#define MS_IN_EP 0x01
|
|
#define MS_OUT_EP 0x02
|
|
|
|
#define USB_LOW_SPEED_DEVICE DISABLE
|
|
|
|
|
|
#define Usb_unicode(a) ((U16)(a))
|
|
|
|
//! @ingroup usbconf
|
|
//! @defgroup device_cst_actions USB device custom actions
|
|
//!
|
|
//! @{
|
|
// write here the action to associate to each USB event
|
|
// be carefull not to waste time in order not disturbing the functions
|
|
#define Usb_sof_action() /* sof_action(); */
|
|
#define Usb_wake_up_action()
|
|
#define Usb_resume_action()
|
|
#define Usb_suspend_action() suspend_action();
|
|
#define Usb_reset_action()
|
|
#define Usb_vbus_on_action()
|
|
#define Usb_vbus_off_action()
|
|
#define Usb_set_configuration_action()
|
|
|
|
|
|
// write here the action to associate to each SCSI event
|
|
// be carefull not to waste time in order not disturbing the functions
|
|
#define Scsi_start_read_action() Led1_on()
|
|
#define Scsi_stop_read_action() Led1_off()
|
|
#define Scsi_start_write_action() Led2_on()
|
|
#define Scsi_stop_write_action() Led2_off()
|
|
|
|
//! @}
|
|
|
|
extern void sof_action(void);
|
|
extern void suspend_action(void);
|
|
//! @}
|
|
|
|
|
|
/** @} */
|
|
|
|
#endif // _CONF_USB_H_
|