osd-contiki/examples/osd/arduino-climate3/sketch.pde
2017-03-03 11:45:46 +01:00

148 lines
4.1 KiB
Plaintext

/*
* Sample arduino sketch using contiki features.
* We turn the LED off
* We allow read the moisture sensor
* Unfortunately sleeping for long times in loop() isn't currently
* possible, something turns off the CPU (including PWM outputs) if a
* Proto-Thread is taking too long. We need to find out how to sleep in
* a Contiki-compatible way.
* Note that for a normal arduino sketch you won't have to include any
* of the contiki-specific files here, the sketch should just work.
*/
#include <Wire.h>
#include "Adafruit_HTU21DF.h"
#include <OneWire.h>
#include "DallasTemperature.h"
extern "C" {
#include "arduino-process.h"
#include "rest-engine.h"
#include "sketch.h"
// Data wire is plugged into port 2 on the Arduino
#define ONE_WIRE_BUS 3
#define TEMPERATURE_PRECISION 9
// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
OneWire oneWire(ONE_WIRE_BUS);
// Pass our oneWire reference to Dallas Temperature.
DallasTemperature dsensors(&oneWire);
// arrays to hold device addresses
DeviceAddress outsideThermometer;
Adafruit_HTU21DF htu = Adafruit_HTU21DF();
extern resource_t res_htu21dtemp, res_htu21dhum, res_dtemp1, res_battery;
float htu21d_hum;
float htu21d_temp;
char htu21d_hum_s[8];
char htu21d_temp_s[8];
float d_temp;
char d_temp_s[8];
// sketch.h
struct dstemp ds1820[7];
#define LED_PIN 4
}
// main functions to print information about a device
void printAddress(uint8_t* adress)
{
printf("%02X",adress[0]);
printf("%02X",adress[1]);
printf("%02X",adress[2]);
printf("%02X",adress[3]);
printf("%02X",adress[4]);
printf("%02X",adress[5]);
printf("%02X",adress[6]);
printf("%02X",adress[7]);
}
// function to print the temperature for a device
void printTemperature(DeviceAddress deviceAddress,int index)
{
d_temp = dsensors.getTempC(deviceAddress);
dtostrf(d_temp , 0, 2, d_temp_s );
printf("Temp C: ");
printf("%s",d_temp_s);
// copy to structure
ds1820[index].ftemp=d_temp;
strcpy(ds1820[index].stemp, d_temp_s);
}
void printData(DeviceAddress deviceAddress, int index)
{
printf("Device Address: ");
printAddress(deviceAddress);
printf(" ");
printTemperature(deviceAddress,index);
printf("\n");
}
void setup (void)
{
// switch off the led
pinMode(LED_PIN, OUTPUT);
digitalWrite(LED_PIN, HIGH);
// ds1820 sensor
printf("Dallas Temperature IC Control Library Demo");
// Start up the library
dsensors.begin();
// locate devices on the bus
printf("Locating devices...\n");
printf("Found ");
printf("%d",dsensors.getDeviceCount());
printf(" devices.\n");
// report parasite power requirements
printf("Parasite power is: ");
if (dsensors.isParasitePowerMode()) printf("ON\n");
else printf("OFF\n");
if (!dsensors.getAddress(outsideThermometer, 0)) printf("Unable to find address for Device 0\n");
// show the addresses we found on the bus
printf("Device 0 Address: ");
printAddress(outsideThermometer);
printf("\n");
// set the resolution to 9 bit
dsensors.setResolution(outsideThermometer, 9);
printf("Device 0 Resolution: ");
printf("%d",dsensors.getResolution(outsideThermometer));
printf("\n");
// htu21d sensor
if (!htu.begin()) {
printf("Couldn't find sensor!");
}
// init coap resourcen
rest_init_engine ();
#pragma GCC diagnostic ignored "-Wwrite-strings"
rest_activate_resource (&res_htu21dtemp, "s/temp");
rest_activate_resource (&res_htu21dhum, "s/hum");
rest_activate_resource (&res_dtemp1, "s/tempd");
rest_activate_resource (&res_battery, "s/battery");
#pragma GCC diagnostic pop
}
// at project-conf.h
// LOOP_INTERVAL (20 * CLOCK_SECOND)
void loop (void)
{
dsensors.requestTemperatures();
// print the device information
//printData(outsideThermometer,0);
htu21d_temp = htu.readTemperature();
htu21d_hum = htu.readHumidity();
dtostrf(htu21d_temp , 0, 2, htu21d_temp_s );
dtostrf(htu21d_hum , 0, 2, htu21d_hum_s );
// debug only
// printf("Temp: %s",htu21d_temp_s);
// printf("\t\tHum: %s\n",htu21d_hum_s);
}