77c02d58f8
Now the necessary settings are in adc.h. Refactored to allow repeated ADC reads without reinitialization. Arduino allows setting analogReference, this is now also implemented. ADC is now initialized to sane values in apps/arduino/arduino-process.c dev/arduino/arduino-compat.h now has all hardware independent settings for arduino (some moved from platform/osd-merkur/dev/hw-arduino.h). turnOffPWM re-implemented with hw_timer, removed from wiring_digital.c ADC-specific arduino stuff moved to arduino-compat.h Arduinos wiring_analog no longer necessary. arduino-sketch example now reads analog inputs 1 and 5 using analogRead.
71 lines
2.2 KiB
Makefile
71 lines
2.2 KiB
Makefile
CONTIKI_TARGET_DIRS = . dev apps net loader
|
|
|
|
CONTIKI_CORE=contiki-main
|
|
CONTIKI_TARGET_MAIN = ${CONTIKI_CORE}.o
|
|
CONTIKI_TARGET_SOURCEFILES += contiki-main.c params.c node-id.c
|
|
#Needed for slip
|
|
CONTIKI_TARGET_SOURCEFILES += temperature-sensor.c adc.c led.c sensors.c slip_uart0.c slip.c leds-arch.c
|
|
#Needed for Button
|
|
CONTIKI_TARGET_SOURCEFILES += button-sensor.c
|
|
# i2c Master
|
|
CONTIKI_TARGET_SOURCEFILES += i2c.c
|
|
#Needed for DHT11 humidity sensor
|
|
CONTIKI_TARGET_SOURCEFILES += dht11.c
|
|
#Needed for DS18S20 temperature sensor
|
|
CONTIKI_TARGET_SOURCEFILES += ds1820.c
|
|
#Needed for Battery test
|
|
CONTIKI_TARGET_SOURCEFILES += battery-sensor.c batmon.c
|
|
#Needed for PIR
|
|
CONTIKI_TARGET_SOURCEFILES += pir-sensor.c
|
|
#Needed for OPTRIAC
|
|
CONTIKI_TARGET_SOURCEFILES += optriac.c optriac-sensor.c
|
|
CONTIKIAVR=$(CONTIKI)/cpu/avr
|
|
#Needed for SERVO
|
|
CONTIKI_TARGET_SOURCEFILES += servo.c servo-sensor.c
|
|
#Needed for Timer4 Servo
|
|
#CONTIKI_TARGET_SOURCEFILES += t4-servo.c t4-servo-sensor.c
|
|
#Needed for Relay 1 to 4
|
|
CONTIKI_TARGET_SOURCEFILES += relay.c relay-sensor.c
|
|
# Arduino
|
|
CONTIKI_TARGET_SOURCEFILES += wiring_digital.c
|
|
|
|
CONTIKIBOARD=.
|
|
BOOTLOADER_START = 0x1F000
|
|
CONTIKI_PLAT_DEFS = -DF_CPU=16000000UL -DAUTO_CRC_PADDING=2 -DPLAT_TIMER=5
|
|
|
|
MCU=atmega128rfa1
|
|
|
|
AVRDUDE_PROGRAMMER=jtag2
|
|
|
|
# For usb devices, you may either use PORT=usb, or (e.g. if you have more than one
|
|
# programmer connected) you can use the following trick to find out the serial number:
|
|
#
|
|
# The example is for an JTAGICE mkII used to program an ATmega128:
|
|
# avrdude -v -P usb:xxxx -c jtag2 -p atmega128
|
|
AVRDUDE_PORT=usb:00B000000D79
|
|
|
|
|
|
# Additional avrdude options
|
|
# Verify off
|
|
AVRDUDE_OPTIONS=-V
|
|
AVRDUDE_MCU=m128rfa1
|
|
|
|
#debug
|
|
# CFLAGS += -save-temps
|
|
# Bootloader bonsai
|
|
# LDFLAGS += -save-temps
|
|
# For the old bonsai bootloader compiled with squeeze gcc-avr we
|
|
# directly used the address of the bootloader:
|
|
#BOOTLOADER_GET_MAC=0x0001f3a0
|
|
# For newer bonsai we have a jump table at the end of the bootloader
|
|
# section:
|
|
BOOTLOADER_GET_MAC=0x0001ff80
|
|
|
|
LDFLAGS += -Wl,--defsym,bootloader_get_mac=$(BOOTLOADER_GET_MAC)
|
|
|
|
|
|
include $(CONTIKIAVR)/Makefile.avr
|
|
include $(CONTIKIAVR)/radio/Makefile.radio
|
|
|
|
MODULES += core/net/ipv6 core/net/ipv4 core/net/ip core/net/mac core/net core/net/rime core/net/rpl core/net/mac/sicslowmac core/net/mac/contikimac
|