deac/osd-contiki
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity
osd-contiki/platform/cc2530dk/contiki-conf.h
George Oikonomou e95f94a9a8 Added support for reading MAC from the cc253x flash 
We still use the primary location by default (Info Page) but
this is now configurable. This change is useful for users who
wish to specify their own MAC address. Since the Info Page is
read-only, they need to be able to use the secondary location
2012-04-20 16:03:38 +01:00

235 lines
6.4 KiB
C
Raw Blame History

#ifndef __CONTIKI_CONF_H__
#define __CONTIKI_CONF_H__
#include "8051def.h"
#include "sys/cc.h"
#include <string.h>
/* Include Project Specific conf */
#ifdef PROJECT_CONF_H
#include "project-conf.h"
#endif /* PROJECT_CONF_H */
/*
* Define this as 1 to poll the etimer process from within main instead of from
* the clock ISR. This reduces the ISR's stack usage and may prevent crashes.
*/
#ifndef CLOCK_CONF_STACK_FRIENDLY
#define CLOCK_CONF_STACK_FRIENDLY 1
#endif
/* Energest Module */
#ifndef ENERGEST_CONF_ON
#define ENERGEST_CONF_ON 0
#endif
/* Verbose Startup? Turning this off saves plenty of bytes of CODE in HOME */
#ifndef STARTUP_CONF_VERBOSE
#define STARTUP_CONF_VERBOSE 0
#endif
/* More CODE space savings by turning off process names */
#define PROCESS_CONF_NO_PROCESS_NAMES 1
/*
* USARTs:
* SmartRF RS232 -> USART0 / Alternative 1 (UART)
* SmartRF LCD -> USART1 / Alternative 2 (SPI)
*/
#define UART_ON_USART 0
#define UART1_CONF_ENABLE 0
#ifndef UART0_CONF_ENABLE
#define UART0_CONF_ENABLE 1
#endif
#ifndef UART0_CONF_WITH_INPUT
#define UART0_CONF_WITH_INPUT 0
#endif
#ifndef UART0_CONF_HIGH_SPEED
#define UART0_CONF_HIGH_SPEED 0
#endif
/* Are we a SLIP bridge? */
#if SLIP_ARCH_CONF_ENABLE
/* Make sure the UART is enabled, with interrupts */
#undef UART0_CONF_ENABLE
#undef UART0_CONF_WITH_INPUT
#define UART0_CONF_ENABLE 1
#define UART0_CONF_WITH_INPUT 1
#define UIP_FALLBACK_INTERFACE slip_interface
#endif
/* Output all captured frames over the UART in hexdump format */
#ifndef CC2530_RF_CONF_HEXDUMP
#define CC2530_RF_CONF_HEXDUMP 0
#endif
#if CC2530_RF_CONF_HEXDUMP
/* We need UART1 output */
#undef UART_ZERO_CONF_ENABLE
#define UART_ZERO_CONF_ENABLE 1
#endif
/* Code Shortcuts */
/*
* When set, this directive also configures the following bypasses:
* - process_post_synch() in tcpip_input() (we call packet_input())
* - process_post_synch() in tcpip_uipcall (we call the relevant pthread)
* - mac_call_sent_callback() is replaced with sent() in various places
*
* These are good things to do, they reduce stack usage and prevent crashes
*/
#define NETSTACK_CONF_SHORTCUTS 1
/*
* By default we read our MAC from the (read-only) Information Page (primary
* location). In order to have a user-programmable mac, define this as 0 to
* use the secondary location (addresses 0xFFE8 - 0xFFEF on the last flash page)
*/
#ifndef CC2530_CONF_MAC_FROM_PRIMARY
#define CC2530_CONF_MAC_FROM_PRIMARY 1
#endif
/*
* Sensors
* It is harmless to #define XYZ 1
* even if the sensor is not present on our device
*/
#ifndef BUTTON_SENSOR_CONF_ON
#define BUTTON_SENSOR_CONF_ON 1 /* Buttons */
#endif
/* ADC - Turning this off will disable everything below */
#ifndef ADC_SENSOR_CONF_ON
#define ADC_SENSOR_CONF_ON 1
#endif
#define TEMP_SENSOR_CONF_ON 1 /* Temperature */
#define VDD_SENSOR_CONF_ON 1 /* Supply Voltage */
#define BATTERY_SENSOR_CONF_ON 0 /* Battery */
/* Low Power Modes - We only support PM0/Idle and PM1 */
#ifndef LPM_CONF_MODE
#define LPM_CONF_MODE 0 /* 0: no LPM, 1: MCU IDLE, 2: Drop to PM1 */
#endif
/* Some files include leds.h before us */
#undef LEDS_YELLOW
#undef LEDS_RED
#define LEDS_YELLOW 4
#define LEDS_RED 2
/* DMA Configuration */
#ifndef DMA_CONF_ON
#define DMA_CONF_ON 0
#endif
/* Viztool on by default for IPv6 builds */
#if UIP_CONF_IPV6
#ifndef VIZTOOL_CONF_ON
#define VIZTOOL_CONF_ON 1
#endif /* VIZTOOL_CONF_ON */
#endif /* UIP_CONF_IPV6 */
/* Network Stack */
#if UIP_CONF_IPV6
#define NETSTACK_CONF_NETWORK sicslowpan_driver
#else
#define NETSTACK_CONF_NETWORK rime_driver
#endif
#ifndef NETSTACK_CONF_MAC
#define NETSTACK_CONF_MAC csma_driver
#endif
#ifndef NETSTACK_CONF_RDC
#define NETSTACK_CONF_RDC nullrdc_driver
#define NULLRDC_802154_AUTOACK 1
#define NULLRDC_802154_AUTOACK_HW 1
#endif
#ifndef NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE
#define NETSTACK_CONF_RDC_CHANNEL_CHECK_RATE 8
#endif
#define NETSTACK_CONF_FRAMER framer_802154
#define NETSTACK_CONF_RADIO cc2530_rf_driver
/* RF Config */
#define IEEE802154_CONF_PANID 0x5449 /* TI */
#ifndef CC2530_RF_CONF_CHANNEL
#define CC2530_RF_CONF_CHANNEL 25
#endif /* CC2530_RF_CONF_CHANNEL */
#ifndef CC2530_RF_CONF_AUTOACK
#define CC2530_RF_CONF_AUTOACK 1
#endif /* CC2530_CONF_AUTOACK */
#if UIP_CONF_IPV6
/* Addresses, Sizes and Interfaces */
/* 8-byte addresses here, 2 otherwise */
#define RIMEADDR_CONF_SIZE 8
#define UIP_CONF_LL_802154 1
#define UIP_CONF_LLH_LEN 0
#define UIP_CONF_NETIF_MAX_ADDRESSES 3
/* TCP, UDP, ICMP */
#define UIP_CONF_TCP 0
#define UIP_CONF_UDP 1
#define UIP_CONF_UDP_CHECKSUMS 1
/* ND and Routing */
#define UIP_CONF_ROUTER 1
#define UIP_CONF_IPV6_RPL 1
#define UIP_CONF_ND6_SEND_RA 0
#define UIP_CONF_IP_FORWARD 0
#define RPL_CONF_STATS 0
#define RPL_CONF_MAX_DAG_ENTRIES 1
#ifndef RPL_CONF_OF
#define RPL_CONF_OF rpl_of_etx
#endif
#define UIP_CONF_ND6_REACHABLE_TIME 600000
#define UIP_CONF_ND6_RETRANS_TIMER 10000
#ifndef UIP_CONF_DS6_NBR_NBU
#define UIP_CONF_DS6_NBR_NBU 4 /* Handle n Neighbors */
#endif
#ifndef UIP_CONF_DS6_ROUTE_NBU
#define UIP_CONF_DS6_ROUTE_NBU 4 /* Handle n Routes */
#endif
/* uIP */
#define UIP_CONF_BUFFER_SIZE 240
#define UIP_CONF_IPV6_QUEUE_PKT 0
#define UIP_CONF_IPV6_CHECKS 1
#define UIP_CONF_IPV6_REASSEMBLY 0
/* 6lowpan */
#define SICSLOWPAN_CONF_COMPRESSION SICSLOWPAN_COMPRESSION_HC06
#ifndef SICSLOWPAN_CONF_FRAG
#define SICSLOWPAN_CONF_FRAG 0 /* About 2KB of CODE if 1 */
#endif
#define SICSLOWPAN_CONF_MAXAGE 8
/* Define our IPv6 prefixes/contexts here */
#define SICSLOWPAN_CONF_MAX_ADDR_CONTEXTS 1
#define SICSLOWPAN_CONF_ADDR_CONTEXT_0 { \
addr_contexts[0].prefix[0] = 0xaa; \
addr_contexts[0].prefix[1] = 0xaa; \
}
#define MAC_CONF_CHANNEL_CHECK_RATE 8
#define QUEUEBUF_CONF_NUM 6
#else /* UIP_CONF_IPV6 */
/* Network setup for non-IPv6 (rime). */
#define UIP_CONF_IP_FORWARD 1
#define UIP_CONF_BUFFER_SIZE 108
#define RIME_CONF_NO_POLITE_ANNOUCEMENTS 0
#define QUEUEBUF_CONF_NUM 8
#endif /* UIP_CONF_IPV6 */
#endif /* __CONTIKI_CONF_H__ */
Reference in a new issue View git blame Copy permalink