deac/osd-contiki
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity
osd-contiki/platform/jn516x/platform-conf.h
Simon Duquennoy bd7d45080d Added NXP JN516x platform
2015-09-23 14:38:31 +02:00

263 lines
8.3 KiB
C
Raw Blame History

/*
* Copyright (c) 2015, SICS Swedish ICT.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the Institute nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* This file is part of the Contiki operating system.
*
*/
#ifndef PLATFORM_CONF_H
#define PLATFORM_CONF_H
#include <inttypes.h>
#include <jendefs.h>
#undef putchar
/* Delay between GO signal and SFD
* Measured 153us between GO and preamble. Add 5 bytes (preamble + SFD) air time: 153+5*32 = 313 */
#define RADIO_DELAY_BEFORE_TX ((unsigned)US_TO_RTIMERTICKS(313))
/* Delay between GO signal and start listening
* Measured 104us: between GO signal and start listening */
#define RADIO_DELAY_BEFORE_RX ((unsigned)US_TO_RTIMERTICKS(104))
/* Micromac configuration */
#ifndef MIRCOMAC_CONF_BUF_NUM
#define MIRCOMAC_CONF_BUF_NUM 2
#endif
#ifndef MICROMAC_CONF_CHANNEL
#define MICROMAC_CONF_CHANNEL 26
#endif
#ifdef RF_CHANNEL
#define MICROMAC_CONF_CHANNEL RF_CHANNEL
#endif
/* Timer conversion
* RTIMER 16M = 256 * 62500(RADIO) == 2^8 * 62500 */
#define RADIO_TO_RTIMER(X) ((rtimer_clock_t)((X) << (int32_t)8L))
#define DR_11744_DIO2 12
#define DR_11744_DIO3 13
#define DR_11744_DIO4 14
#define DR_11744_DIO5 15
#define DR_11744_DIO6 16
#define DR_11744_DIO7 17
#define TSCH_DEBUG 0
#if TSCH_DEBUG
#define TSCH_DEBUG_INIT() do { \
vAHI_DioSetDirection(0, (1 << DR_11744_DIO2) | (1 << DR_11744_DIO3) | (1 << DR_11744_DIO4) | (1 << DR_11744_DIO5) | (1 << DR_11744_DIO6) | (1 << DR_11744_DIO7)); \
vAHI_DioSetOutput(0, (1 << DR_11744_DIO2) | (1 << DR_11744_DIO3) | (1 << DR_11744_DIO4) | (1 << DR_11744_DIO5) | (1 << DR_11744_DIO6) | (1 << DR_11744_DIO7)); } while(0);
#define TSCH_DEBUG_INTERRUPT() do { \
static dio_state = 0; \
dio_state = !dio_state; \
if(dio_state) { \
vAHI_DioSetOutput((1 << DR_11744_DIO2), 0); \
} else { \
vAHI_DioSetOutput(0, (1 << DR_11744_DIO2)); \
} \
} while(0);
#define TSCH_DEBUG_RX_EVENT() do { \
static dio_state = 0; \
dio_state = !dio_state; \
if(dio_state) { \
vAHI_DioSetOutput((1 << DR_11744_DIO4), 0); \
} else { \
vAHI_DioSetOutput(0, (1 << DR_11744_DIO4)); \
} \
} while(0);
#define TSCH_DEBUG_TX_EVENT() do { \
static dio_state = 0; \
dio_state = !dio_state; \
if(dio_state) { \
vAHI_DioSetOutput((1 << DR_11744_DIO5), 0); \
} else { \
vAHI_DioSetOutput(0, (1 << DR_11744_DIO5)); \
} \
} while(0);
#define TSCH_DEBUG_SLOT_START() do { \
static dio_state = 0; \
dio_state = !dio_state; \
if(dio_state) { \
vAHI_DioSetOutput((1 << DR_11744_DIO3), 0); \
} else { \
vAHI_DioSetOutput(0, (1 << DR_11744_DIO3)); \
} \
} while(0);
#define TSCH_DEBUG_SLOT_END()
#endif /* TSCH_DEBUG */
#ifndef BAUD2UBR
#define BAUD2UBR(X) (X)
#endif /* BAUD2UBR */
/* UART baud rates */
#define UART_RATE_4800 0
#define UART_RATE_9600 1
#define UART_RATE_19200 2
#define UART_RATE_38400 3
#define UART_RATE_76800 4
#define UART_RATE_115200 5
#define UART_RATE_230400 6
#define UART_RATE_460800 7
#define UART_RATE_500000 8
#define UART_RATE_576000 9
#define UART_RATE_921600 10
#define UART_RATE_1000000 11
#define PLATFORM_HAS_LEDS 1
#define PLATFORM_HAS_BUTTON (SENSOR_BOARD_DR1174 == 1)
#define PLATFORM_HAS_LIGHT (SENSOR_BOARD_DR1175 == 1)
#define PLATFORM_HAS_HT (SENSOR_BOARD_DR1175 == 1)
#define PLATFORM_HAS_POT (SENSOR_BOARD_DR1199 == 1)
#define PLATFORM_HAS_BATTERY 0 /* sensor driver not implemented */
#define PLATFORM_HAS_SHT11 0
#define PLATFORM_HAS_RADIO 1
/* CPU target speed in Hz
* RTIMER and peripherals clock is F_CPU/2 */
#define F_CPU 32000000UL
/* LED ports */
/*
#define LEDS_PxDIR P5DIR
#define LEDS_PxOUT P5OUT
#define LEDS_CONF_RED 0x10
#define LEDS_CONF_GREEN 0x20
#define LEDS_CONF_YELLOW 0x40
#define JENNIC_CONF_BUTTON_PIN (IRQ_DIO9|IRQ_DIO10)
*/
#define CC_CONF_REGISTER_ARGS 1
#define CC_CONF_FUNCTION_POINTER_ARGS 1
#define CC_CONF_FASTCALL
#define CC_CONF_VA_ARGS 1
#define CC_CONF_INLINE inline
#define CCIF
#define CLIF
#ifdef HAVE_STDINT_H
#include <stdint.h>
#else
#ifndef uint8_t
typedef unsigned char uint8_t;
typedef unsigned short uint16_t;
typedef unsigned long uint32_t;
typedef signed char int8_t;
typedef short int16_t;
typedef long int32_t;
typedef unsigned long long uint64_t;
typedef long long int64_t;
#endif
#endif /* !HAVE_STDINT_H */
/* Types for clocks and uip_stats */
typedef uint16_t uip_stats_t;
typedef uint32_t clock_time_t;
/* Core rtimer.h defaults to 16 bit timer unless RTIMER_CLOCK_LT is defined */
typedef uint32_t rtimer_clock_t;
#define RTIMER_CLOCK_LT(a, b) ((int32_t)((a) - (b)) < 0)
/* 10ms timer tick */
#define CLOCK_CONF_SECOND 100
/* Shall we calibrate the DCO periodically? */
#define DCOSYNCH_CONF_ENABLED 1
/* How often shall we attempt to calibrate DCO?
* PS: It should be calibrated upon temperature changes,
* but the naive approach of periodic calibration is fine too */
#ifndef DCOSYNCH_PERIOD
#define DCOSYNCH_PERIOD (5 * 60)
#endif /* VCO_CALIBRATION_INTERVAL */
/* Disable UART HW flow control */
#ifndef UART_HW_FLOW_CTRL
#define UART_HW_FLOW_CTRL 0
#endif /* UART_HW_FLOW_CTRL */
/* Disable UART SW flow control */
#ifndef UART_XONXOFF_FLOW_CTRL
#define UART_XONXOFF_FLOW_CTRL 1
#endif /* UART_XONXOFF_FLOW_CTRL */
#ifndef UART_BAUD_RATE
#define UART_BAUD_RATE UART_RATE_1000000
#endif /* UART_BAUD_RATE */
#ifndef UART1_BAUD_RATE
#define UART1_BAUD_RATE UART_RATE_1000000
#endif
#define ENABLE_ADVANCED_BAUD_SELECTION (UART_BAUD_RATE > UART_RATE_115200)
/* Set this to zero only if we are using SLIP */
#ifndef SLIP_BRIDGE_CONF_NO_PUTCHAR
#define SLIP_BRIDGE_CONF_NO_PUTCHAR 1
#endif /* SLIP_BRIDGE_CONF_NO_PUTCHAR */
/* Enable this to get the 32.768kHz oscillator */
#ifndef USE_EXTERNAL_OSCILLATOR
#define USE_EXTERNAL_OSCILLATOR 0
#endif /* USE_EXTERNAL_OSCILLATOR */
/* Extension of LED definitions from leds.h for various JN516x dev boards
JN516x Dongle:
LEDS_RED Red LED on dongle
LEDS_GREEN Green LED on dongle
Note: Only one LED can be switch on at the same time
DR1174-only:
LEDS_GP0 LED D3 on DR1174
LEDS_GP1 LED D6 on DR1174
DR1174+DR1199:
LEDS_RED LED D1 on DR1199
LEDS_GREEN LED D2 on DR1199
LEDS_BLUE LED D3 on DR1199
LEDS_GP0 LED D3 on DR1174
LEDS_GP1 LED D6 on DR1174
DR1174+DR1175:
LEDS_RED Red led in RGB-led with level control on DR1175
LEDS_GREEN Green led in RGB-led with level control on DR1175
LEDS_BLUE Blue led in RGB-led with level control on DR1175
LEDS_WHITE White power led with level control on DR1175
LEDS_GP0 LEDS D3 on DR1174
LEDS_GP1 LEDS D6 on DR1174
*/
#define LEDS_WHITE 8
#define LEDS_GP0 16
#define LEDS_GP1 32
#define LEDS_GP2 64
#define LEDS_GP3 128
#define LEDS_CONF_ALL 255
#endif /* PLATFORM_CONF_H */
Reference in a new issue View git blame Copy permalink