665c58fd2a
CC1020
o Turns off only after transmission has ended and not in between
o Using events for DMA takes too long. It should use a callback when
DMA finishes to turn off the transmit mode as early as possible.
Core/UART
o Added profiling and energest initialization
o Changed low-power mode from LPM1 to LPM3
254 lines
6.7 KiB
C
254 lines
6.7 KiB
C
#include <signal.h>
|
|
|
|
#define CC1020_MAIN 0x00
|
|
#define CC1020_INTERFACE 0x01
|
|
#define CC1020_RESET 0x02
|
|
#define CC1020_SEQUENCING 0x03
|
|
#define CC1020_FREQ_2A 0x04
|
|
#define CC1020_FREQ_1A 0x05
|
|
#define CC1020_FREQ_0A 0x06
|
|
#define CC1020_CLOCK_A 0x07
|
|
#define CC1020_FREQ_2B 0x08
|
|
#define CC1020_FREQ_1B 0x09
|
|
#define CC1020_FREQ_0B 0x0A
|
|
#define CC1020_CLOCK_B 0x0B
|
|
#define CC1020_VCO 0x0C
|
|
#define CC1020_MODEM 0x0D
|
|
#define CC1020_DEVIATION 0x0E
|
|
#define CC1020_AFC_CONTROL 0x0F
|
|
#define CC1020_FILTER 0x10
|
|
#define CC1020_VGA1 0x11
|
|
#define CC1020_VGA2 0x12
|
|
#define CC1020_VGA3 0x13
|
|
#define CC1020_VGA4 0x14
|
|
#define CC1020_LOCK 0x15
|
|
#define CC1020_FRONTEND 0x16
|
|
#define CC1020_ANALOG 0x17
|
|
#define CC1020_BUFF_SWING 0x18
|
|
#define CC1020_BUFF_CURRENT 0x19
|
|
#define CC1020_PLL_BW 0x1A
|
|
#define CC1020_CALIBRATE 0x1B
|
|
#define CC1020_PA_POWER 0x1C
|
|
#define CC1020_MATCH 0x1D
|
|
#define CC1020_PHASE_COMP 0x1E
|
|
#define CC1020_GAIN_COMP 0x1F
|
|
#define CC1020_POWERDOWN 0x20
|
|
#define CC1020_TEST1 0x21
|
|
#define CC1020_TEST2 0x22
|
|
#define CC1020_TEST3 0x23
|
|
#define CC1020_TEST4 0x24
|
|
#define CC1020_TEST5 0x25
|
|
#define CC1020_TEST6 0x26
|
|
#define CC1020_TEST7 0x27
|
|
#define CC1020_STATUS 0x40
|
|
#define CC1020_RESET_DONE 0x41
|
|
#define CC1020_RSS 0x42
|
|
#define CC1020_AFC 0x43
|
|
#define CC1020_GAUSS_FILTER 0x44
|
|
#define CC1020_STATUS1 0x45
|
|
#define CC1020_STATUS2 0x46
|
|
#define CC1020_STATUS3 0x47
|
|
#define CC1020_STATUS4 0x48
|
|
#define CC1020_STATUS5 0x49
|
|
#define CC1020_STATUS6 0x4A
|
|
#define CC1020_STATUS7 0x4B
|
|
|
|
/* Flags for the MAIN register. */
|
|
#define RESET_N 1
|
|
#define BIAS_PD (1<<1)
|
|
#define XOSC_PD (1<<2)
|
|
#define FS_PD (1<<3)
|
|
#define PD_MODE_1 (1<<4)
|
|
#define PD_MODE_2 (1<<5)
|
|
#define F_REG (1<<6)
|
|
#define RXTX (1<<7)
|
|
|
|
/* In power up mode, the MAIN register modifies some flags to the following. */
|
|
#define SEQ_PD (1<<1)
|
|
#define SEQ_CAL_1 (1<<2)
|
|
#define SEQ_CAL_2 (1<<3)
|
|
|
|
// For CC1020_STATUS
|
|
#define CARRIER_SENSE 0x08
|
|
#define LOCK_CONTINUOUS 0x10
|
|
#define LOCK_INSTANT 0x20
|
|
#define SEQ_ERROR 0x40
|
|
#define CAL_COMPLETE 0x80
|
|
|
|
#define PA_POWER 0x0F // initial default for output power
|
|
#define LOCK_NOK 0x00
|
|
#define LOCK_OK 0x01
|
|
#define LOCK_RECAL_OK 0x02
|
|
#define CAL_TIMEOUT 0x7FFE
|
|
#define LOCK_TIMEOUT 0x7FFE
|
|
#define RESET_TIMEOUT 0x7FFE
|
|
#define TX_CURRENT 0x87
|
|
#define RX_CURRENT 0x86
|
|
|
|
// CC1020 driver configuration
|
|
#define CC1020_BUFFERSIZE 250
|
|
|
|
// PDI (Data in) is on P21
|
|
#define PDO (P2IN & 0x01)
|
|
|
|
// PSEL is on P30 and low active
|
|
#define PSEL_ON do { P3OUT &= ~0x01; } while(0)
|
|
#define PSEL_OFF do { P3OUT |= 0x01; } while(0)
|
|
#define PCLK_HIGH do { P2OUT |= 0x08; } while(0)
|
|
#define PCLK_LOW do { P2OUT &= ~0x08; } while(0)
|
|
|
|
// PDO (Data out) is on P22
|
|
#define PDI_HIGH do { P2OUT |= 0x02; } while(0)
|
|
|
|
#define PDI_LOW do { P2OUT &= ~0x02; } while(0)
|
|
|
|
// Enable power for LNA (P24, low-active)
|
|
#define LNA_POWER_ON() do { P2OUT &= ~0x10; } while(0)
|
|
|
|
#define LNA_POWER_OFF() do { P2OUT |= 0x10; } while(0)
|
|
|
|
#define CC_LOCK (P2IN & 0x04)
|
|
|
|
#define DISABLE_RX_IRQ() \
|
|
do { IE1 &= ~(URXIE0); } while(0)
|
|
|
|
#define ENABLE_RX_IRQ() \
|
|
do { IFG1 &= ~URXIFG0; IE1 |= URXIE0; } while(0)
|
|
|
|
#define ACK_TIMEOUT_115 4 // In RADIO_STROKE ticks
|
|
#define ACK_TIMEOUT_19 16
|
|
|
|
#define MHZ_869525 1
|
|
|
|
const uint8_t cc1020_config_19200[41] = {
|
|
0x01, // 0x00, MAIN
|
|
0x0F, // 0x01, INTERFACE
|
|
0xFF, // 0x02, RESET
|
|
0x8F, // 0x03, SEQUENCING
|
|
// 869.525 at 50kHz
|
|
0x3A, // 0x04, FREQ_2A
|
|
0x32, // 0x05, FREQ_1A
|
|
0x97, // 0x06, FREQ_0A // 19200
|
|
0x38, // 0x07, CLOCK_A // 19200
|
|
0x3A, // 0x08, FREQ_2B
|
|
0x37, // 0x09, FREQ_1B
|
|
0xEB, // 0x0A, FREQ_0B // 19200
|
|
0x38, // 0x0B, CLOCK_B // 19200
|
|
0x44, // 0x0C, VCO 44
|
|
0x51, // 0x0D, MODEM Manchester
|
|
0x2B, // 0x0E, DEVIATION // FSK
|
|
0x4C, // 0x0F, AFC_CONTROL Ruetten 0xCC
|
|
0x25, // 0x10, FILTER Bandwith 100 kHz
|
|
0x61, // 0x11, VGA1
|
|
0x55, // 0x12, VGA2
|
|
0x2D, // 0x13, VGA3
|
|
0x37, // 0x14, VGA4 // 0x29, VGA4 ADJUSTED CS to 23!
|
|
0x40, // 0x15, LOCK is Carrier SENSE
|
|
0x76, // 0x16, FRONTEND
|
|
0x87, // 0x17, ANALOG, RX=86/TX=87
|
|
0x10, // 0x18, BUFF_SWING
|
|
0x25, // 0x19, BUFF_CURRENT
|
|
0xAE, // 0x1A, PLL_BW
|
|
0x34, // 0x1B, CALIBRATE
|
|
PA_POWER, // 0x1C, PA_POWER AN025 = 0xA0
|
|
0xF0, // 0x1D, MATCH
|
|
0x00, // 0x1E, PHASE_COMP
|
|
0x00, // 0x1F, GAIN_COMP
|
|
0x00, // 0x20, POWERDOWN
|
|
0x4d, // 0x4d, // 0x21,
|
|
0x10, // 0x10, // 0x22,
|
|
0x06, // 0x06, // 0x23,
|
|
0x00, // 0x00, // 0x24,
|
|
0x40, // 0x40, // 0x25,
|
|
0x00, // 0x00, // 0x26,
|
|
0x00, // 0x00, // 0x27,
|
|
// Not in real config of chipCon from here!!!
|
|
ACK_TIMEOUT_19
|
|
};
|
|
|
|
const uint8_t cc1020_config_115200[41] = {
|
|
0x01, // 0x00, MAIN
|
|
0x0F, // 0x01, INTERFACE
|
|
0xFF, // 0x02, RESET
|
|
0x8F, // 0x03, SEQUENCING
|
|
// 869.525 at 200kHz
|
|
0x3A, // 0x04, FREQ_2A
|
|
0x32, // 0x05, FREQ_1A
|
|
0x97, // 0x06, FREQ_0A // 19200
|
|
0x29, // 0x07, CLOCK_A // 19200
|
|
0x3A, // 0x08, FREQ_2B
|
|
0x37, // 0x09, FREQ_1B
|
|
0xEB, // 0x0A, FREQ_0B // 19200
|
|
0x29, // 0x0B, CLOCK_B // 19200
|
|
0x44, // 0x0C, VCO 44
|
|
0x51, // 0x0D, MODEM Manchester
|
|
0x58, // 0x0E, DEVIATION // FSK
|
|
0x4C, // 0x0F, AFC_CONTROL Ruetten 0xCC
|
|
0x80, // 0x10, FILTER Bandwith 500 kHz
|
|
0x61, // 0x11, VGA1
|
|
0x55, // 0x12, VGA2
|
|
0x30, // 0x13, VGA3
|
|
0x35, // 0x14, VGA4
|
|
0x20, // 0x15, LOCK is Carrier SENSE
|
|
0x76, // 0x16, FRONTEND
|
|
0x87, // 0x17, ANALOG, RX=86/TX=87
|
|
0x10, // 0x18, BUFF_SWING
|
|
0x25, // 0x19, BUFF_CURRENT
|
|
0xAE, // 0x1A, PLL_BW
|
|
0x34, // 0x1B, CALIBRATE
|
|
PA_POWER, // 0x1C, PA_POWER AN025 = 0xA0
|
|
0xF0, // 0x1D, MATCH
|
|
0x00, // 0x1E, PHASE_COMP
|
|
0x00, // 0x1F, GAIN_COMP
|
|
0x00, // 0x20, POWERDOWN
|
|
0x4d, // 0x21,
|
|
0x10, // 0x22,
|
|
0x06, // 0x23,
|
|
0x00, // 0x24,
|
|
0x40, // 0x25,
|
|
0x00, // 0x26,
|
|
0x00, // 0x27,
|
|
// Not in real config of chipCon from here!!!
|
|
ACK_TIMEOUT_115
|
|
};
|
|
|
|
/// cc1020 state
|
|
enum cc1020_state {
|
|
CC1020_OFF = 0,
|
|
CC1020_RX = 0x01,
|
|
CC1020_TX = 0x02,
|
|
|
|
CC1020_RX_SEARCHING = 0x10, // searching for preamble + sync word
|
|
CC1020_RX_RECEIVING = 0x20, // receiving bytes
|
|
CC1020_RX_PROCESSING = 0x40, // processing data in buffer
|
|
|
|
CC1020_OP_STATE = 0x73,
|
|
|
|
CC1020_TURN_OFF = 0x80,
|
|
};
|
|
|
|
#define CC1020_SET_OPSTATE(opstate) cc1020_state = ((cc1020_state & ~CC1020_OP_STATE) | (opstate))
|
|
|
|
/******************************************************************************
|
|
* @name Packet specification
|
|
* @{
|
|
*/
|
|
|
|
const uint8_t syncword[2] = {0xD3,0x91};
|
|
|
|
// header: number of bytes in packet including header
|
|
struct cc1020_header {
|
|
uint8_t length;
|
|
} __attribute__((packed));
|
|
|
|
|
|
#define PREAMBLESIZE 6
|
|
#define PREAMBLE 0xAA
|
|
#define TAILSIZE 2
|
|
#define TAIL 0xFA
|
|
|
|
#define SYNCWDSIZE (sizeof (syncword))
|
|
#define HDRSIZE (sizeof (struct cc1020_header))
|
|
|
|
///@}
|