d2f3795a30
Homogenize port and pin definitions naming: - PERIPHERAL_FUNCTION_PORT for the port ID, - PERIPHERAL_FUNCTION_PIN for the pin ID, - PERIPHERAL_FUNCTION_PORT_BASE for the port base, - PERIPHERAL_FUNCTION_PIN_MASK for the pin mask. Define only PERIPHERAL_FUNCTION_PORT and PERIPHERAL_FUNCTION_PIN in board.h, and deduce PERIPHERAL_FUNCTION_PORT_BASE and PERIPHERAL_FUNCTION_PIN_MASK in the driver from the former definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
135 lines
5 KiB
C
135 lines
5 KiB
C
/*
|
|
* Copyright (c) 2013, University of Michigan.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the University nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
/**
|
|
* \addtogroup cc2538-spi
|
|
* @{
|
|
*
|
|
* \file
|
|
* Implementation of the cc2538 SPI peripheral
|
|
*/
|
|
#include "contiki.h"
|
|
#include "reg.h"
|
|
#include "spi-arch.h"
|
|
#include "dev/ioc.h"
|
|
#include "dev/sys-ctrl.h"
|
|
#include "dev/spi.h"
|
|
#include "dev/ssi.h"
|
|
#include "dev/gpio.h"
|
|
|
|
#define SPI_CLK_PORT_BASE GPIO_PORT_TO_BASE(SPI_CLK_PORT)
|
|
#define SPI_CLK_PIN_MASK GPIO_PIN_MASK(SPI_CLK_PIN)
|
|
#define SPI_MOSI_PORT_BASE GPIO_PORT_TO_BASE(SPI_MOSI_PORT)
|
|
#define SPI_MOSI_PIN_MASK GPIO_PIN_MASK(SPI_MOSI_PIN)
|
|
#define SPI_MISO_PORT_BASE GPIO_PORT_TO_BASE(SPI_MISO_PORT)
|
|
#define SPI_MISO_PIN_MASK GPIO_PIN_MASK(SPI_MISO_PIN)
|
|
#define SPI_SEL_PORT_BASE GPIO_PORT_TO_BASE(SPI_SEL_PORT)
|
|
#define SPI_SEL_PIN_MASK GPIO_PIN_MASK(SPI_SEL_PIN)
|
|
|
|
/* Default: Motorola mode 3 with 8-bit data words */
|
|
#ifndef SPI_CONF_PHASE
|
|
#define SPI_CONF_PHASE SSI_CR0_SPH
|
|
#endif
|
|
#ifndef SPI_CONF_POLARITY
|
|
#define SPI_CONF_POLARITY SSI_CR0_SPO
|
|
#endif
|
|
#ifndef SPI_CONF_DATA_SIZE
|
|
#define SPI_CONF_DATA_SIZE 8
|
|
#endif
|
|
|
|
#if SPI_CONF_DATA_SIZE < 4 || SPI_CONF_DATA_SIZE > 16
|
|
#error SPI_CONF_DATA_SIZE must be set between 4 and 16 inclusive.
|
|
#endif
|
|
|
|
/**
|
|
* \brief Initialize the SPI bus.
|
|
*
|
|
* This SPI init() function uses the following #defines to set the pins:
|
|
* SPI_CLK_PORT SPI_CLK_PIN
|
|
* SPI_MOSI_PORT SPI_MOSI_PIN
|
|
* SPI_MISO_PORT SPI_MISO_PIN
|
|
* SPI_SEL_PORT SPI_SEL_PIN
|
|
*
|
|
* This sets the mode to Motorola SPI with the following format options:
|
|
* SPI_CONF_PHASE: 0 or SSI_CR0_SPH
|
|
* SPI_CONF_POLARITY: 0 or SSI_CR0_SPO
|
|
* SPI_CONF_DATA_SIZE: 4 to 16 bits
|
|
*/
|
|
void
|
|
spi_init(void)
|
|
{
|
|
spi_enable();
|
|
|
|
/* Start by disabling the peripheral before configuring it */
|
|
REG(SSI0_BASE + SSI_CR1) = 0;
|
|
|
|
/* Set the IO clock as the SSI clock */
|
|
REG(SSI0_BASE + SSI_CC) = 1;
|
|
|
|
/* Set the mux correctly to connect the SSI pins to the correct GPIO pins */
|
|
ioc_set_sel(SPI_CLK_PORT, SPI_CLK_PIN, IOC_PXX_SEL_SSI0_CLKOUT);
|
|
ioc_set_sel(SPI_MOSI_PORT, SPI_MOSI_PIN, IOC_PXX_SEL_SSI0_TXD);
|
|
REG(IOC_SSIRXD_SSI0) = (SPI_MISO_PORT * 8) + SPI_MISO_PIN;
|
|
ioc_set_sel(SPI_SEL_PORT, SPI_SEL_PIN, IOC_PXX_SEL_SSI0_FSSOUT);
|
|
|
|
/* Put all the SSI gpios into peripheral mode */
|
|
GPIO_PERIPHERAL_CONTROL(SPI_CLK_PORT_BASE, SPI_CLK_PIN_MASK);
|
|
GPIO_PERIPHERAL_CONTROL(SPI_MOSI_PORT_BASE, SPI_MOSI_PIN_MASK);
|
|
GPIO_PERIPHERAL_CONTROL(SPI_MISO_PORT_BASE, SPI_MISO_PIN_MASK);
|
|
GPIO_PERIPHERAL_CONTROL(SPI_SEL_PORT_BASE, SPI_SEL_PIN_MASK);
|
|
|
|
/* Disable any pull ups or the like */
|
|
ioc_set_over(SPI_CLK_PORT, SPI_CLK_PIN, IOC_OVERRIDE_DIS);
|
|
ioc_set_over(SPI_MOSI_PORT, SPI_MOSI_PIN, IOC_OVERRIDE_DIS);
|
|
ioc_set_over(SPI_MISO_PORT, SPI_MISO_PIN, IOC_OVERRIDE_DIS);
|
|
ioc_set_over(SPI_SEL_PORT, SPI_SEL_PIN, IOC_OVERRIDE_DIS);
|
|
|
|
/* Configure the clock */
|
|
REG(SSI0_BASE + SSI_CPSR) = 2;
|
|
|
|
/* Put the ssi in Motorola SPI mode using the provided format options */
|
|
REG(SSI0_BASE + SSI_CR0) = SPI_CONF_PHASE | SPI_CONF_POLARITY | (SPI_CONF_DATA_SIZE - 1);
|
|
|
|
/* Enable the SSI */
|
|
REG(SSI0_BASE + SSI_CR1) |= SSI_CR1_SSE;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
spi_enable(void)
|
|
{
|
|
/* Enable the clock for the SSI peripheral */
|
|
REG(SYS_CTRL_RCGCSSI) |= 1;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
spi_disable(void)
|
|
{
|
|
/* Gate the clock for the SSI peripheral */
|
|
REG(SYS_CTRL_RCGCSSI) &= ~1;
|
|
}
|
|
/** @} */
|