96 lines
3.5 KiB
C
96 lines
3.5 KiB
C
/* Timer registers are all 16-bit wide with 16-bit access only */
|
|
#define TMR_OFFSET (0x20)
|
|
#define TMR_BASE (0x80007000)
|
|
#define TMR0_BASE (TMR_BASE)
|
|
#define TMR1_BASE (TMR_BASE + TMR_OFFSET*1)
|
|
#define TMR2_BASE (TMR_BASE + TMR_OFFSET*2)
|
|
#define TMR3_BASE (TMR_BASE + TMR_OFFSET*3)
|
|
|
|
#define TMR_REGOFF_COMP1 (0x0)
|
|
#define TMR_REGOFF_COMP2 (0x2)
|
|
#define TMR_REGOFF_CAPT (0x4)
|
|
#define TMR_REGOFF_LOAD (0x6)
|
|
#define TMR_REGOFF_HOLD (0x8)
|
|
#define TMR_REGOFF_CNTR (0xa)
|
|
#define TMR_REGOFF_CTRL (0xc)
|
|
#define TMR_REGOFF_SCTRL (0xe)
|
|
#define TMR_REGOFF_CMPLD1 (0x10)
|
|
#define TMR_REGOFF_CMPLD2 (0x12)
|
|
#define TMR_REGOFF_CSCTRL (0x14)
|
|
#define TMR_REGOFF_ENBL (0x1e)
|
|
|
|
/* Timer 0 registers */
|
|
#define TMR0_COMP1 (TMR0_BASE + TMR_REGOFF_COMP1)
|
|
#define TMR0_COMP_UP TMR0_COMP1
|
|
#define TMR0_COMP2 (TMR0_BASE + TMR_REGOFF_COMP2)
|
|
#define TMR0_COMP_DOWN TMR0_COMP2
|
|
#define TMR0_CAPT (TMR0_BASE + TMR_REGOFF_CAPT)
|
|
#define TMR0_LOAD (TMR0_BASE + TMR_REGOFF_LOAD)
|
|
#define TMR0_HOLD (TMR0_BASE + TMR_REGOFF_HOLD)
|
|
#define TMR0_CNTR (TMR0_BASE + TMR_REGOFF_CTRL)
|
|
#define TMR0_CTRL (TMR0_BASE + TMR_REGOFF_CTRL)
|
|
#define TMR0_SCTRL (TMR0_BASE + TMR_REGOFF_SCTRL)
|
|
#define TMR0_CMPLD1 (TMR0_BASE + TMR_REGOFF_CMPLD1)
|
|
#define TMR0_CMPLD2 (TMR0_BASE + TMR_REGOFF_CMPLD2)
|
|
#define TMR0_CSCTRL (TMR0_BASE + TMR_REGOFF_CSCTRL)
|
|
|
|
/* one enable register to rule them all */
|
|
#define TMR_ENBL TMR0_BASE + TMR_REGOFF_ENBL
|
|
|
|
#define MBAR_GPIO 0x80000000
|
|
#define GPIO_PAD_DIR0 0x80000000
|
|
#define GPIO_DATA0 0x80000008
|
|
#define UART1_DATA 0x80005008
|
|
#define DELAY 400000
|
|
|
|
#define reg32(x) (*(volatile uint32_t *)(x))
|
|
#define reg16(x) (*(volatile uint16_t *)(x))
|
|
|
|
#include "embedded_types.h"
|
|
|
|
#include "isr.h"
|
|
no_isrs();
|
|
|
|
__attribute__ ((section ("startup")))
|
|
void main(void) {
|
|
|
|
/* pin direction */
|
|
reg32(GPIO_PAD_DIR0) = 0x00000400;
|
|
|
|
/* timer setup */
|
|
/* CTRL */
|
|
#define COUNT_MODE 1 /* use rising edge of primary source */
|
|
#define PRIME_SRC 0xf /* Perip. clock with 128 prescale (for 24Mhz = 187500Hz)*/
|
|
#define SEC_SRC 0 /* don't need this */
|
|
#define ONCE 0 /* keep counting */
|
|
#define LEN 1 /* count until compare then reload with value in LOAD */
|
|
#define DIR 0 /* count up */
|
|
#define CO_INIT 0 /* other counters cannot force a re-initialization of this counter */
|
|
#define OUT_MODE 0 /* OFLAG is asserted while counter is active */
|
|
|
|
reg16(TMR_ENBL) = 0; /* tmrs reset to enabled */
|
|
reg16(TMR0_SCTRL) = 0;
|
|
reg16(TMR0_LOAD) = 0; /* reload to zero */
|
|
reg16(TMR0_COMP_UP) = 18750; /* trigger a reload at the end */
|
|
reg16(TMR0_CMPLD1) = 18750; /* compare 1 triggered reload level, 10HZ maybe? */
|
|
reg16(TMR0_CNTR) = 0; /* reset count register */
|
|
reg16(TMR0_CTRL) = (COUNT_MODE<<13) | (PRIME_SRC<<9) | (SEC_SRC<<7) | (ONCE<<6) | (LEN<<5) | (DIR<<4) | (CO_INIT<<3) | (OUT_MODE);
|
|
reg16(TMR_ENBL) = 0xf; /* enable all the timers --- why not? */
|
|
|
|
while(1) {
|
|
|
|
/* blink on */
|
|
reg32(GPIO_DATA0) = 0x00000400;
|
|
|
|
while((reg16(TMR0_SCTRL)>>15) == 0) { continue; }
|
|
reg16(TMR0_SCTRL) = 0; /*clear bit 15, and all the others --- should be ok, but clearly not "the right thing to do" */
|
|
|
|
/* blink off */
|
|
reg32(GPIO_DATA0) = 0x00000000;
|
|
|
|
while((reg16(TMR0_SCTRL)>>15) == 0) { continue; }
|
|
reg16(TMR0_SCTRL) = 0; /*clear bit 15, and all the others --- should be ok, but clearly not "the right thing to do" */
|
|
|
|
};
|
|
}
|