116 lines
4.2 KiB
C
116 lines
4.2 KiB
C
/*
|
|
* Copyright (c) 2015, Zolertia
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* \addtogroup remote-antenna
|
|
* @{
|
|
*
|
|
* Driver for the RE-Mote RF switch, to enable either the built-in 2.4GHz RF
|
|
* interface of the CC2538, or the CC1200 Sub-1GHz RF interface, both routed to
|
|
* the RP-SMA connector for an external antenna.
|
|
* When the 2.4GHz RF interface is enabled, the CC1200 is powered down.
|
|
* When the CC1200 is enabled, alternatively the 2.4GHz can be also used if
|
|
* placing an 0Ohm resistor (R19), to connect either via a non-mounted chip
|
|
* antenna, or with an external antenna connected to a non-mounted U.Fl
|
|
* connector with a pigtail.
|
|
*
|
|
* RF switch state:
|
|
* - LOW: 2.4GHz RF interface on RP-SMA connector, CC1200 powered-off.
|
|
* - HIGH: Sub-1GHz RF interface on RP-SMA connector.
|
|
* @{
|
|
*
|
|
* \file
|
|
* Driver for the RE-Mote RF antenna switch
|
|
*/
|
|
/*---------------------------------------------------------------------------*/
|
|
#include "contiki.h"
|
|
#include "dev/gpio.h"
|
|
#include "antenna-sw.h"
|
|
|
|
#include <stdint.h>
|
|
/*---------------------------------------------------------------------------*/
|
|
#define ANTENNA_RF_SW_PORT_BASE GPIO_PORT_TO_BASE(ANTENNA_RF_SW_PORT)
|
|
#define ANTENNA_RF_SW_PIN_MASK GPIO_PIN_MASK(ANTENNA_RF_SW_PIN)
|
|
/*---------------------------------------------------------------------------*/
|
|
static uint8_t initialized = 0;
|
|
/*---------------------------------------------------------------------------*/
|
|
void
|
|
antenna_sw_config(void)
|
|
{
|
|
/* Software controlled */
|
|
GPIO_SOFTWARE_CONTROL(ANTENNA_RF_SW_PORT_BASE,
|
|
ANTENNA_RF_SW_PIN_MASK);
|
|
|
|
/* Set pin to output */
|
|
GPIO_SET_OUTPUT(ANTENNA_RF_SW_PORT_BASE, ANTENNA_RF_SW_PIN_MASK);
|
|
|
|
/* Set the antenna selector to a default position */
|
|
GPIO_WRITE_PIN(ANTENNA_RF_SW_PORT_BASE, ANTENNA_RF_SW_PIN_MASK,
|
|
ANTENNA_SW_SELECT_DEFAULT);
|
|
|
|
initialized = 1;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
int
|
|
antenna_sw_get(void)
|
|
{
|
|
if(!initialized) {
|
|
return ANTENNA_SW_SELECT_ERROR;
|
|
}
|
|
|
|
/* Set the antenna selector */
|
|
return GPIO_READ_PIN(ANTENNA_RF_SW_PORT_BASE, ANTENNA_RF_SW_PIN_MASK);
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
int
|
|
antenna_sw_select(uint8_t val)
|
|
{
|
|
if(!initialized) {
|
|
return ANTENNA_SW_SELECT_ERROR;
|
|
}
|
|
|
|
if(val != ANTENNA_SW_SELECT_SUBGHZ && val != ANTENNA_SW_SELECT_2_4GHZ) {
|
|
return ANTENNA_SW_SELECT_ERROR;
|
|
}
|
|
|
|
if(val & antenna_sw_get()) {
|
|
return val;
|
|
}
|
|
|
|
/* Set the antenna selector */
|
|
GPIO_WRITE_PIN(ANTENNA_RF_SW_PORT_BASE, ANTENNA_RF_SW_PIN_MASK, val);
|
|
|
|
return val;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/**
|
|
* @}
|
|
* @}
|
|
*/
|