a5046e83c7
This is a general cleanup of things like code style issues and code structure of the STM32w port to make it more like the rest of Contiki is structured.
127 lines
5 KiB
C
127 lines
5 KiB
C
/** @file hal/micro/cortexm3/flash.h
|
|
* @brief Header for flash for APIs
|
|
*
|
|
* <!--(C) COPYRIGHT 2010 STMicroelectronics. All rights reserved. -->
|
|
*/
|
|
|
|
/** @addtogroup flash
|
|
* @brief Definition and description of public flash manipulation routines.
|
|
*
|
|
* @note
|
|
* During an erase or a write the flash is not available,
|
|
* which means code will not be executable from flash. These routines still
|
|
* execute from flash, though, since the bus architecture can support doing so.
|
|
* <b>Additonally, this also means all interrupts will be disabled.</b>
|
|
*
|
|
* <b>Hardware documentation indicates 40us for a write and 21ms for an erase.</b>
|
|
*
|
|
* See flash.h for source code.
|
|
*@{
|
|
*/
|
|
|
|
#ifndef __FLASH_H__
|
|
#define __FLASH_H__
|
|
|
|
#include "memmap.h"
|
|
|
|
|
|
/** @brief Tells the calling code if a Flash Erase operation is active.
|
|
*
|
|
* This state is import to know because Flash Erasing is ATOMIC for 21ms
|
|
* and could disrupt interrupt latency. But if an ISR can know that it wasn't
|
|
* serviced immediately due to Flash Erasing, then the ISR has the opportunity
|
|
* to correct in whatever manner it needs to.
|
|
*
|
|
* @return A boolean flag: TRUE if Flash Erase is active, FALSE otherwise.
|
|
*/
|
|
boolean halFlashEraseIsActive(void);
|
|
|
|
#ifndef DOXYGEN_SHOULD_SKIP_THIS
|
|
|
|
//[[ The following eraseType definitions must match the FIB erase types! ]]
|
|
/**
|
|
* @brief Assign numerical value to the type of erasure requested.
|
|
*/
|
|
#define MFB_MASS_ERASE 0x01
|
|
#define MFB_PAGE_ERASE 0x02
|
|
#define CIB_ERASE 0x03
|
|
|
|
/** @brief Erases a section of flash back to all 0xFFFF.
|
|
*
|
|
* @param eraseType Choose one of the three types of erasures to perform.
|
|
* - MFB_MASS_ERASE (0x01) Erase the entire main flash block.
|
|
* - MFB_PAGE_ERASE (0x02) Erase one hardware page in the main flash block
|
|
* chosen by the \c address parameter.
|
|
* - CIB_ERASE (0x03) Erase the entire customer information block.
|
|
*
|
|
* @param address This parameter is only effectual when a MFB_PAGE_ERASE is
|
|
* being performed. The hardware page encapsulating the address given in this
|
|
* parameter will be erased. A hardware page size depends on the chip
|
|
*
|
|
* @return An ::StStatus value indicating the success or failure of the
|
|
* command:
|
|
* - ST_ERR_FATAL if the \c eraseType is not valid
|
|
* - ST_ERR_FLASH_ERASE_FAIL if erasing failed due to write protection
|
|
* - ST_ERR_FLASH_VERIFY_FAILED if erase verification failed
|
|
* - ST_SUCCESS if erasure completed and verified properly
|
|
*/
|
|
StStatus halInternalFlashErase(uint8_t eraseType, uint32_t address);
|
|
|
|
/** @brief Writes a block of words to flash. A page is erased
|
|
* to 0xFFFF at every address. Only two writes can be performed to the same
|
|
* address between erasures and this is enforced by the flash interface
|
|
* controller. If the value already in the address being written to is 0xFFFF,
|
|
* any value can be written. If the value is not 0xFFFF and not 0x0000, only
|
|
* 0x0000 can be written. If the value is 0x0000, nothing can be written.
|
|
*
|
|
* \b NOTE: This function can NOT write the option bytes and will throw an
|
|
* error if that is attempted.
|
|
*
|
|
* @param address The starting address of where the programming will occur.
|
|
* This parameter MUST be half-word aligned since all programming operations
|
|
* are half-words. Also, the address parameter is NOT a pointer. This
|
|
* routines will cast the address to a pointer for the actual hardware access.
|
|
*
|
|
* @param data A pointer to a buffer containing the 16bit (half-words) to
|
|
* be written.
|
|
*
|
|
* @param length The number of 16bit (half-words) contained in the data buffer
|
|
* to be written to flash.
|
|
*
|
|
* @return An ::StStatus value indicating the success or failure of the
|
|
* command:
|
|
* - ST_ERR_FLASH_PROG_FAIL if the address is not half-word aligned, the
|
|
* address is inside the option bytes, write protection is enabled, or the
|
|
* address is being written to more than twice between erasures.
|
|
* - ST_ERR_FLASH_VERIFY_FAILED if write verification failed
|
|
* - ST_SUCCESS if writing completed and verified properly
|
|
*/
|
|
StStatus halInternalFlashWrite(uint32_t address, uint16_t * data, uint32_t length);
|
|
|
|
/** @brief Writes an option byte to the customer information block. Only
|
|
* two writes can be performed to the same address between erasures and this
|
|
* is enforced by the flash interface controller.
|
|
*
|
|
* @param byte The option byte number, 0 though 7, to be programmed.
|
|
*
|
|
* @param data The 8 bit value to be programmed into the option byte. The
|
|
* hardware is responsible for calculating the compliment and programming
|
|
* the full 16bit option byte space.
|
|
*
|
|
* @return An ::StStatus value indicating the success or failure of the
|
|
* command:
|
|
* - ST_ERR_FLASH_PROG_FAIL if the byte chosen is greater than 7, write
|
|
* protection is enabled, or the byte is being written to more than twice
|
|
* between erasures.
|
|
* - ST_ERR_FLASH_VERIFY_FAILED if write verification failed
|
|
* - ST_SUCCESS if writing completed and verified properly
|
|
*/
|
|
StStatus halInternalCibOptionByteWrite(uint8_t byte, uint8_t data);
|
|
|
|
#endif //DOXYGEN_SHOULD_SKIP_THIS
|
|
|
|
#endif //__FLASH_H__
|
|
|
|
/** @} END addtogroup */
|
|
|