osd-contiki/cpu/msp430/dev/uart1.c

212 lines
6.1 KiB
C

/*
* Copyright (c) 2006, Swedish Institute of Computer Science
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the Institute nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* @(#)$Id: uart1.c,v 1.12 2009/09/08 10:39:49 nifi Exp $
*/
/*
* Machine dependent MSP430 UART1 code.
*/
#include <stdlib.h>
#include <io.h>
#include <signal.h>
#include "sys/energest.h"
#include "dev/uart1.h"
#include "dev/watchdog.h"
#include "lib/ringbuf.h"
static int (*uart1_input_handler)(unsigned char c);
static uint8_t rx_in_progress;
static volatile uint8_t transmitting;
#define TX_WITH_INTERRUPT 1
#if TX_WITH_INTERRUPT
#define TXBUFSIZE 64
static struct ringbuf txbuf;
static uint8_t txbuf_data[TXBUFSIZE];
#endif /* TX_WITH_INTERRUPT */
/*---------------------------------------------------------------------------*/
uint8_t
uart1_active(void)
{
return ((~ UTCTL1) & TXEPT) | rx_in_progress | transmitting;
}
/*---------------------------------------------------------------------------*/
void
uart1_set_input(int (*input)(unsigned char c))
{
uart1_input_handler = input;
}
/*---------------------------------------------------------------------------*/
void
uart1_writeb(unsigned char c)
{
watchdog_periodic();
#if TX_WITH_INTERRUPT
/* Put the outgoing byte on the transmission buffer. If the buffer
is full, we just keep on trying to put the byte into the buffer
until it is possible to put it there. */
while(ringbuf_put(&txbuf, c) == 0);
/* If there is no transmission going, we need to start it by putting
the first byte into the UART. */
if(transmitting == 0) {
transmitting = 1;
TXBUF1 = ringbuf_get(&txbuf);
}
#else /* TX_WITH_INTERRUPT */
/* Loop until the transmission buffer is available. */
while((IFG2 & UTXIFG1) == 0);
/* Transmit the data. */
TXBUF1 = c;
#endif /* TX_WITH_INTERRUPT */
}
/*---------------------------------------------------------------------------*/
#if ! WITH_UIP /* If WITH_UIP is defined, putchar() is defined by the SLIP driver */
int
putchar(int c)
{
uart1_writeb((char)c);
return c;
}
#endif /* ! WITH_UIP */
/*---------------------------------------------------------------------------*/
/**
* Initalize the RS232 port.
*
*/
void
uart1_init(unsigned long ubr)
{
/* RS232 */
P3DIR &= ~0x80; /* Select P37 for input (UART1RX) */
P3DIR |= 0x40; /* Select P36 for output (UART1TX) */
P3SEL |= 0xC0; /* Select P36,P37 for UART1{TX,RX} */
UCTL1 = SWRST | CHAR; /* 8-bit character, UART mode */
#if 0
U1RCTL &= ~URXEIE; /* even erroneous characters trigger interrupts */
#endif
UTCTL1 = SSEL1; /* UCLK = MCLK */
UBR01 = ubr;
UBR11 = ubr >> 8;
/*
* UMCTL1 values calculated using
* http://mspgcc.sourceforge.net/baudrate.html
* Table assumes that F_CPU = 2,457,600 Hz.
*/
switch(ubr) {
case UART1_BAUD2UBR(115200ul):
UMCTL1 = 0x4a;
break;
case UART1_BAUD2UBR(57600ul):
UMCTL1 = 0x5b;
break;
default:
/* 9600, 19200, 38400 don't require any correction */
UMCTL1 = 0x00;
}
ME2 &= ~USPIE1; /* USART1 SPI module disable */
ME2 |= (UTXE1 | URXE1); /* Enable USART1 TXD/RXD */
UCTL1 &= ~SWRST;
/* XXX Clear pending interrupts before enable!!! */
IFG2 &= ~URXIFG1;
U1TCTL |= URXSE;
rx_in_progress = 0;
transmitting = 0;
IE2 |= URXIE1; /* Enable USART1 RX interrupt */
#if TX_WITH_INTERRUPT
ringbuf_init(&txbuf, txbuf_data, sizeof(txbuf_data));
IE2 |= UTXIE1; /* Enable USART1 TX interrupt */
#endif /* TX_WITH_INTERRUPT */
}
/*---------------------------------------------------------------------------*/
interrupt(UART1RX_VECTOR)
uart1_rx_interrupt(void)
{
ENERGEST_ON(ENERGEST_TYPE_IRQ);
if(!(URXIFG1 & IFG2)) {
/* Edge detect if IFG not set? */
U1TCTL &= ~URXSE; /* Clear the URXS signal */
U1TCTL |= URXSE; /* Re-enable URXS - needed here?*/
rx_in_progress = 1;
LPM4_EXIT;
} else {
rx_in_progress = 0;
/* Check status register for receive errors. */
if(URCTL1 & RXERR) {
volatile unsigned dummy;
dummy = RXBUF1; /* Clear error flags by forcing a dummy read. */
} else {
if(uart1_input_handler != NULL) {
if(uart1_input_handler(RXBUF1)) {
LPM4_EXIT;
}
}
}
}
ENERGEST_OFF(ENERGEST_TYPE_IRQ);
}
/*---------------------------------------------------------------------------*/
#if TX_WITH_INTERRUPT
interrupt(UART1TX_VECTOR)
uart1_tx_interrupt(void)
{
ENERGEST_ON(ENERGEST_TYPE_IRQ);
if(ringbuf_elements(&txbuf) == 0) {
transmitting = 0;
} else {
TXBUF1 = ringbuf_get(&txbuf);
}
ENERGEST_OFF(ENERGEST_TYPE_IRQ);
}
#endif /* TX_WITH_INTERRUPT */
/*---------------------------------------------------------------------------*/