185 lines
3.4 KiB
C
185 lines
3.4 KiB
C
#include <mc1322x.h>
|
|
#include <board.h>
|
|
|
|
#include "tests.h"
|
|
#include "config.h"
|
|
|
|
#define DELAY 100000
|
|
#define DATA 0x00401000;
|
|
|
|
uint32_t ackBox[10];
|
|
|
|
#define command_xcvr_rx() \
|
|
do { \
|
|
maca_txlen = (uint32_t)1<<16; \
|
|
maca_dmatx = (uint32_t)&ackBox; \
|
|
maca_dmarx = DATA; \
|
|
maca_tmren = (maca_cpl_clk | maca_soft_clk); \
|
|
maca_control = (control_prm | control_asap | control_seq_rx); \
|
|
}while(0)
|
|
|
|
#define PAYLOAD_LEN 16 /* not including the extra 4 bytes for len+fcs+somethingelse */
|
|
/* maca dmatx needs extra 4 bytes for checksum */
|
|
/* needs + 4 bytes for len(1 byte) + fcs(2 bytes) + somethingelse */
|
|
#define command_xcvr_tx() \
|
|
do { \
|
|
maca_txlen = (uint32_t)(PAYLOAD_LEN+4); \
|
|
maca_dmatx = (uint32_t)DATA; \
|
|
maca_dmarx = (uint32_t)&ackBox; \
|
|
maca_control = (control_prm | control_mode_no_cca | \
|
|
control_asap | control_seq_tx); \
|
|
}while(0)
|
|
|
|
|
|
volatile uint8_t led;
|
|
#define LED LED_RED
|
|
#define led_on() do { led = 1; *GPIO_DATA0 = LED; } while(0);
|
|
#define led_off() do { led = 0; *GPIO_DATA0 = 0x00000000; } while(0);
|
|
|
|
void toggle_led(void) {
|
|
if(0 == led) {
|
|
led_on();
|
|
led = 1;
|
|
|
|
} else {
|
|
led_off();
|
|
}
|
|
}
|
|
|
|
volatile uint8_t *data;
|
|
uint8_t count=0;
|
|
void fill_data(void) {
|
|
uint8_t i;
|
|
for(i=0; i<PAYLOAD_LEN; i++) {
|
|
data[i] = count++;
|
|
}
|
|
}
|
|
|
|
void main(void) {
|
|
volatile uint32_t i;
|
|
uint16_t status;
|
|
|
|
*GPIO_PAD_DIR0 = LED;
|
|
led_on();
|
|
|
|
uart_init(INC,MOD);
|
|
|
|
reset_maca();
|
|
radio_init();
|
|
vreg_init();
|
|
flyback_init();
|
|
init_phy();
|
|
|
|
/* trim the reference osc. to 24MHz */
|
|
pack_XTAL_CNTL(CTUNE_4PF, CTUNE, FTUNE, IBIAS);
|
|
|
|
set_power(0x0f); /* 0dbm */
|
|
set_channel(0); /* channel 11 */
|
|
|
|
*MACA_CONTROL = SMAC_MACA_CNTL_INIT_STATE;
|
|
for(i=0; i<DELAY; i++) { continue; }
|
|
|
|
data = (void *)DATA;
|
|
*MACA_DMARX = DATA; /* put data somewhere */
|
|
*MACA_PREAMBLE = 0;
|
|
|
|
/* sets up tx_on, should be a board specific item */
|
|
*GPIO_FUNC_SEL2 = (0x01 << ((44-16*2)*2));
|
|
*GPIO_PAD_DIR0 = *GPIO_PAD_DIR0 | (1<<(44-32));
|
|
|
|
fill_data();
|
|
command_xcvr_tx();
|
|
|
|
while(1) {
|
|
|
|
if(_is_action_complete_interrupt(maca_irq)) {
|
|
maca_clrirq = maca_irq;
|
|
|
|
status = *MACA_STATUS & 0x0000ffff;
|
|
switch(status)
|
|
{
|
|
case(cc_aborted):
|
|
{
|
|
putstr("aborted\n\r");
|
|
ResumeMACASync();
|
|
break;
|
|
|
|
}
|
|
case(cc_not_completed):
|
|
{
|
|
putstr("not completed\n\r");
|
|
ResumeMACASync();
|
|
break;
|
|
|
|
}
|
|
case(cc_timeout):
|
|
{
|
|
putstr("timeout\n\r");
|
|
ResumeMACASync();
|
|
break;
|
|
|
|
}
|
|
case(cc_no_ack):
|
|
{
|
|
putstr("no ack\n\r");
|
|
ResumeMACASync();
|
|
break;
|
|
|
|
}
|
|
case(cc_ext_timeout):
|
|
{
|
|
putstr("ext timeout\n\r");
|
|
ResumeMACASync();
|
|
break;
|
|
|
|
}
|
|
case(cc_ext_pnd_timeout):
|
|
{
|
|
putstr("ext pnd timeout\n\r");
|
|
ResumeMACASync();
|
|
break;
|
|
|
|
}
|
|
case(cc_success):
|
|
{
|
|
// putstr("success\n\r");
|
|
|
|
putstr("rftest-tx --- " );
|
|
putstr(" payload len+crc: 0x");
|
|
put_hex(PAYLOAD_LEN+4);
|
|
putstr(" timestamp: 0x");
|
|
put_hex32(maca_timestamp);
|
|
putstr("\n\r");
|
|
putstr(" data: ");
|
|
for(i=0; i<PAYLOAD_LEN; i++) {
|
|
put_hex(data[i]);
|
|
putchr(' ');
|
|
}
|
|
putstr("\n\r");
|
|
|
|
toggle_led();
|
|
|
|
fill_data();
|
|
command_xcvr_tx();
|
|
|
|
break;
|
|
|
|
}
|
|
default:
|
|
{
|
|
putstr("status: ");
|
|
put_hex16(status);
|
|
ResumeMACASync();
|
|
|
|
}
|
|
}
|
|
} else if (_is_filter_failed_interrupt(maca_irq)) {
|
|
putstr("filter failed\n\r");
|
|
ResumeMACASync();
|
|
}
|
|
|
|
for(i=0; i<DELAY; i++) { continue; }
|
|
|
|
};
|
|
}
|