osd-contiki/platform/osd-merkur/Makefile.osd-merkur
Ralf Schlatterbeck 77c02d58f8 Refactor A/D conversion in adc.c
Now the necessary settings are in adc.h. Refactored to allow repeated
ADC reads without reinitialization. Arduino allows setting
analogReference, this is now also implemented.
ADC is now initialized to sane values in apps/arduino/arduino-process.c
dev/arduino/arduino-compat.h now has all hardware independent settings
for arduino (some moved from platform/osd-merkur/dev/hw-arduino.h).
turnOffPWM re-implemented with hw_timer, removed from wiring_digital.c
ADC-specific arduino stuff moved to arduino-compat.h
Arduinos wiring_analog no longer necessary.
arduino-sketch example now reads analog inputs 1 and 5 using analogRead.
2014-06-29 17:26:15 +02:00

71 lines
2.2 KiB
Makefile

CONTIKI_TARGET_DIRS = . dev apps net loader
CONTIKI_CORE=contiki-main
CONTIKI_TARGET_MAIN = ${CONTIKI_CORE}.o
CONTIKI_TARGET_SOURCEFILES += contiki-main.c params.c node-id.c
#Needed for slip
CONTIKI_TARGET_SOURCEFILES += temperature-sensor.c adc.c led.c sensors.c slip_uart0.c slip.c leds-arch.c
#Needed for Button
CONTIKI_TARGET_SOURCEFILES += button-sensor.c
# i2c Master
CONTIKI_TARGET_SOURCEFILES += i2c.c
#Needed for DHT11 humidity sensor
CONTIKI_TARGET_SOURCEFILES += dht11.c
#Needed for DS18S20 temperature sensor
CONTIKI_TARGET_SOURCEFILES += ds1820.c
#Needed for Battery test
CONTIKI_TARGET_SOURCEFILES += battery-sensor.c batmon.c
#Needed for PIR
CONTIKI_TARGET_SOURCEFILES += pir-sensor.c
#Needed for OPTRIAC
CONTIKI_TARGET_SOURCEFILES += optriac.c optriac-sensor.c
CONTIKIAVR=$(CONTIKI)/cpu/avr
#Needed for SERVO
CONTIKI_TARGET_SOURCEFILES += servo.c servo-sensor.c
#Needed for Timer4 Servo
#CONTIKI_TARGET_SOURCEFILES += t4-servo.c t4-servo-sensor.c
#Needed for Relay 1 to 4
CONTIKI_TARGET_SOURCEFILES += relay.c relay-sensor.c
# Arduino
CONTIKI_TARGET_SOURCEFILES += wiring_digital.c
CONTIKIBOARD=.
BOOTLOADER_START = 0x1F000
CONTIKI_PLAT_DEFS = -DF_CPU=16000000UL -DAUTO_CRC_PADDING=2 -DPLAT_TIMER=5
MCU=atmega128rfa1
AVRDUDE_PROGRAMMER=jtag2
# For usb devices, you may either use PORT=usb, or (e.g. if you have more than one
# programmer connected) you can use the following trick to find out the serial number:
#
# The example is for an JTAGICE mkII used to program an ATmega128:
# avrdude -v -P usb:xxxx -c jtag2 -p atmega128
AVRDUDE_PORT=usb:00B000000D79
# Additional avrdude options
# Verify off
AVRDUDE_OPTIONS=-V
AVRDUDE_MCU=m128rfa1
#debug
# CFLAGS += -save-temps
# Bootloader bonsai
# LDFLAGS += -save-temps
# For the old bonsai bootloader compiled with squeeze gcc-avr we
# directly used the address of the bootloader:
#BOOTLOADER_GET_MAC=0x0001f3a0
# For newer bonsai we have a jump table at the end of the bootloader
# section:
BOOTLOADER_GET_MAC=0x0001ff80
LDFLAGS += -Wl,--defsym,bootloader_get_mac=$(BOOTLOADER_GET_MAC)
include $(CONTIKIAVR)/Makefile.avr
include $(CONTIKIAVR)/radio/Makefile.radio
MODULES += core/net/ipv6 core/net/ipv4 core/net/ip core/net/mac core/net core/net/rime core/net/rpl core/net/mac/sicslowmac core/net/mac/contikimac