deac/osd-contiki
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity
osd-contiki/cpu/stm32w108/hal/micro/cortexm3/adc.c
Salvatore Pitrulli 01a7a78a94 Fixed temperature ADC conversion bug on mbxxx. 
The conversion was made from an incorrect source when
the GPIO pin was not PB7.
Added functions and macros used to select the correct
ADC channel.
2011-04-20 18:06:20 +02:00

381 lines
11 KiB
C
Raw Blame History

/** @file adc.c
* @brief ADC HAL functions
*
* <!--(C) COPYRIGHT 2010 STMicroelectronics. All rights reserved. -->
*/
#include PLATFORM_HEADER
#include "hal/error.h"
#include "hal/hal.h"
#include "hal/micro/adc.h"
#if (NUM_ADC_USERS > 8)
#error NUM_ADC_USERS must not be greater than 8, or int8u variables in adc.c must be changed
#endif
static int16u adcData; // conversion result written by DMA
static int8u adcPendingRequests; // bitmap of pending requests
volatile static int8u adcPendingConversion; // id of pending conversion
static int8u adcReadingValid; // bitmap of valid adcReadings
static int16u adcReadings[NUM_ADC_USERS];
static int16u adcConfig[NUM_ADC_USERS];
static boolean adcCalibrated;
static int16s Nvss;
static int16s Nvdd;
/* Modified the original ADC driver for enabling the ADC extended range mode required for
supporting the STLM20 temperature sensor.
NOTE:
The ADC extended range is inaccurate due to the high voltage mode bug of the general purpose ADC
(see STM32W108 errata). As consequence, it is not reccomended to use this ADC driver for getting
the temperature values
*/
#ifdef ENABLE_ADC_EXTENDED_RANGE_BROKEN
static int16s Nvref;
static int16s Nvref2;
#endif /* ENABLE_ADC_EXTENDED_RANGE_BROKEN */
static int16u adcStaticConfig;
void halAdcSetClock(boolean slow)
{
if (slow) {
adcStaticConfig |= ADC_1MHZCLK_MASK;
} else {
adcStaticConfig &= ~ADC_1MHZCLK_MASK;
}
}
void halAdcSetRange(boolean high)
{
if (high) {
adcStaticConfig |= (ADC_HVSELP_MASK | ADC_HVSELN_MASK);
} else {
adcStaticConfig &= ~(ADC_HVSELP_MASK | ADC_HVSELN_MASK);
}
}
boolean halAdcGetClock(void)
{
/* Fix original function code */
return (adcStaticConfig & ADC_1MHZCLK_MASK) ? TRUE : FALSE;
}
boolean halAdcGetRange(void)
{
/* Fix original function code */
return (adcStaticConfig & ((ADC_HVSELP_MASK | ADC_HVSELN_MASK))) ? TRUE : FALSE;
}
// Define a channel field that combines ADC_MUXP and ADC_MUXN
#define ADC_CHAN (ADC_MUXP | ADC_MUXN)
#define ADC_CHAN_BIT ADC_MUXN_BIT
void halAdcIsr(void)
{
int8u i;
int8u conversion = adcPendingConversion; //fix 'volatile' warning; costs no flash
// make sure data is ready and the desired conversion is valid
if ( (INT_ADCFLAG & INT_ADCULDFULL)
&& (conversion < NUM_ADC_USERS) ) {
adcReadings[conversion] = adcData;
adcReadingValid |= BIT(conversion); // mark the reading as valid
// setup the next conversion if any
if (adcPendingRequests) {
for (i = 0; i < NUM_ADC_USERS; i++) {
if (BIT(i) & adcPendingRequests) {
adcPendingConversion = i; // set pending conversion
adcPendingRequests ^= BIT(i); //clear request: conversion is starting
ADC_CFG = adcConfig[i];
break; //conversion started, so we're done here (only one at a time)
}
}
} else { // no conversion to do
ADC_CFG = 0; // disable adc
adcPendingConversion = NUM_ADC_USERS; //nothing pending, so go "idle"
}
}
INT_ADCFLAG = 0xFFFF;
asm("DMB");
}
// An internal support routine called from functions below.
// Returns the user number of the started conversion, or NUM_ADC_USERS
// otherwise.
ADCUser startNextConversion()
{
int8u i;
ATOMIC (
// start the next requested conversion if any
if (adcPendingRequests && !(ADC_CFG & ADC_ENABLE)) {
for (i = 0; i < NUM_ADC_USERS; i++) {
if ( BIT(i) & adcPendingRequests) {
adcPendingConversion = i; // set pending conversion
adcPendingRequests ^= BIT(i); // clear request
ADC_CFG = adcConfig[i]; // set the configuration to desired
INT_ADCFLAG = 0xFFFF;
INT_CFGSET = INT_ADC;
break; //see DDTS MBTst38936
}
}
} else {
i = NUM_ADC_USERS;
}
)
return i;
}
void halInternalInitAdc(void)
{
// reset the state variables
adcPendingRequests = 0;
adcPendingConversion = NUM_ADC_USERS;
adcCalibrated = FALSE;
adcStaticConfig = ADC_1MHZCLK | ADC_ENABLE; // init config: 1MHz, low voltage
// set all adcReadings as invalid
adcReadingValid = 0;
// turn off the ADC
ADC_CFG = 0; // disable ADC, turn off HV buffers
ADC_OFFSET = ADC_OFFSET_RESET;
ADC_GAIN = ADC_GAIN_RESET;
ADC_DMACFG = ADC_DMARST;
ADC_DMABEG = (int32u)&adcData;
ADC_DMASIZE = 1;
ADC_DMACFG = (ADC_DMAAUTOWRAP | ADC_DMALOAD);
// clear the ADC interrupts and enable
INT_ADCCFG = INT_ADCULDFULL;
INT_ADCFLAG = 0xFFFF;
INT_CFGSET = INT_ADC;
stCalibrateVref();
}
StStatus halStartAdcConversion(ADCUser id,
ADCReferenceType reference,
ADCChannelType channel,
ADCRateType rate)
{
if(reference != ADC_REF_INT)
return ST_ERR_FATAL;
// save the chosen configuration for this user
adcConfig[id] = ( ((rate << ADC_PERIOD_BIT) & ADC_PERIOD)
| ((channel << ADC_CHAN_BIT) & ADC_CHAN)
| adcStaticConfig);
// if the user already has a pending request, overwrite params
if (adcPendingRequests & BIT(id)) {
return ST_ADC_CONVERSION_DEFERRED;
}
ATOMIC (
// otherwise, queue the transaction
adcPendingRequests |= BIT(id);
// try and start the conversion if there is not one happening
adcReadingValid &= ~BIT(id);
)
if (startNextConversion() == id)
return ST_ADC_CONVERSION_BUSY;
else
return ST_ADC_CONVERSION_DEFERRED;
}
StStatus halRequestAdcData(ADCUser id, int16u *value)
{
//Both the ADC interrupt and the global interrupt need to be enabled,
//otherwise the ADC ISR cannot be serviced.
boolean intsAreOff = ( INTERRUPTS_ARE_OFF()
|| !(INT_CFGSET & INT_ADC)
|| !(INT_ADCCFG & INT_ADCULDFULL) );
StStatus stat;
ATOMIC (
// If interupts are disabled but the flag is set,
// manually run the isr...
//FIXME -= is this valid???
if( intsAreOff
&& ( (INT_CFGSET & INT_ADC) && (INT_ADCCFG & INT_ADCULDFULL) )) {
halAdcIsr();
}
// check if we are done
if (BIT(id) & adcReadingValid) {
*value = adcReadings[id];
adcReadingValid ^= BIT(id);
stat = ST_ADC_CONVERSION_DONE;
} else if (adcPendingRequests & BIT(id)) {
stat = ST_ADC_CONVERSION_DEFERRED;
} else if (adcPendingConversion == id) {
stat = ST_ADC_CONVERSION_BUSY;
} else {
stat = ST_ADC_NO_CONVERSION_PENDING;
}
)
return stat;
}
StStatus halReadAdcBlocking(ADCUser id, int16u *value)
{
StStatus stat;
do {
stat = halRequestAdcData(id, value);
if (stat == ST_ADC_NO_CONVERSION_PENDING)
break;
} while(stat != ST_ADC_CONVERSION_DONE);
return stat;
}
StStatus halAdcCalibrate(ADCUser id)
{
StStatus stat;
/* Modified the original ADC driver for enabling the ADC extended range mode required for
supporting the STLM20 temperature sensor.
NOTE:
The ADC extended range is inaccurate due to the high voltage mode bug of the general purpose ADC
(see STM32W108 errata). As consequence, it is not reccomended to use this ADC driver for getting
the temperature values
*/
#ifdef ENABLE_ADC_EXTENDED_RANGE_BROKEN
if(halAdcGetRange()){
halStartAdcConversion(id,
ADC_REF_INT,
ADC_SOURCE_VREF_VREF2,
ADC_CONVERSION_TIME_US_4096);
stat = halReadAdcBlocking(id, (int16u *)(&Nvref));
if (stat == ST_ADC_CONVERSION_DONE) {
halStartAdcConversion(id,
ADC_REF_INT,
ADC_SOURCE_VREF2_VREF2,
ADC_CONVERSION_TIME_US_4096);
stat = halReadAdcBlocking(id, (int16u *)(&Nvref2));
}
if (stat == ST_ADC_CONVERSION_DONE) {
adcCalibrated = TRUE;
} else {
adcCalibrated = FALSE;
stat = ST_ERR_FATAL;
}
return stat;
}
#endif /* ENABLE_ADC_EXTENDED_RANGE_BROKEN */
halStartAdcConversion(id,
ADC_REF_INT,
ADC_SOURCE_GND_VREF2,
ADC_CONVERSION_TIME_US_4096);
stat = halReadAdcBlocking(id, (int16u *)(&Nvss));
if (stat == ST_ADC_CONVERSION_DONE) {
halStartAdcConversion(id,
ADC_REF_INT,
ADC_SOURCE_VREG2_VREF2,
ADC_CONVERSION_TIME_US_4096);
stat = halReadAdcBlocking(id, (int16u *)(&Nvdd));
}
if (stat == ST_ADC_CONVERSION_DONE) {
Nvdd -= Nvss;
adcCalibrated = TRUE;
} else {
adcCalibrated = FALSE;
stat = ST_ERR_FATAL;
}
return stat;
}
// Use the ratio of the sample reading to the of VDD_PADSA/2, known to be 900mV,
// to convert to 100uV units.
// FIXME: support external Vref
// use #define of Vref, ignore VDD_PADSA
// FIXME: support high voltage range
// use Vref-Vref/2 to calibrate
// FIXME: check for mfg token specifying measured VDD_PADSA
int16s halConvertValueToVolts(int16u value)
{
int32s N;
int16s V;
int32s nvalue;
if (!adcCalibrated) {
halAdcCalibrate(ADC_USER_LQI);
}
if (adcCalibrated) {
/* Modified the original ADC driver for enabling the ADC extended range mode required for
supporting the STLM20 temperature sensor.
NOTE:
The ADC extended range is inaccurate due to the high voltage mode bug of the general purpose ADC
(see STM32W108 errata). As consequence, it is not reccomended to use this ADC driver for getting
the temperature values
*/
#ifdef ENABLE_ADC_EXTENDED_RANGE_BROKEN
if(halAdcGetRange()){ // High range.
N = (((int32s)value + Nvref - 2*Nvref2) << 16)/(2*(Nvref-Nvref2));
// Calculate voltage with: V = (N * VREF) / (2^16) where VDD = 1.2 volts
// Mutiplying by 1.2*10000 makes the result of this equation 100 uVolts
V = (int16s)((N*12000L) >> 16);
if (V > 21000) { // VDD_PADS ?
V = 21000;
}
}
else {
#endif /* ENABLE_ADC_EXTENDED_RANGE_BROKEN */
assert(Nvdd);
nvalue = value - Nvss;
// Convert input value (minus ground) to a fraction of VDD/2.
N = ((nvalue << 16) + Nvdd/2) / Nvdd;
// Calculate voltage with: V = (N * VDD/2) / (2^16) where VDD/2 = 0.9 volts
// Mutiplying by0.9*10000 makes the result of this equation 100 uVolts
// (in fixed point E-4 which allows for 13.5 bits vs millivolts
// which is only 10.2 bits).
V = (int16s)((N*9000L) >> 16);
if (V > 12000) {
V = 12000;
}
#ifdef ENABLE_ADC_EXTENDED_RANGE_BROKEN
}
#endif /* ENABLE_ADC_EXTENDED_RANGE_BROKEN */
} else {
V = -32768;
}
return V;
}
int8u halGetADCChannelFromGPIO(int32u io)
{
switch(io)
{
case PORTB_PIN(5):
return ADC_MUX_ADC0;
case PORTB_PIN(6):
return ADC_MUX_ADC1;
case PORTB_PIN(7):
return ADC_MUX_ADC2;
case PORTC_PIN(1):
return ADC_MUX_ADC3;
case PORTA_PIN(4):
return ADC_MUX_ADC4;
case PORTA_PIN(5):
return ADC_MUX_ADC5;
case PORTB_PIN(0):
return ADC_MUX_VREF;
default :
return 0x0F; // Invalid analogue source
}
}
Reference in a new issue View git blame Copy permalink