125 lines
4.4 KiB
C
125 lines
4.4 KiB
C
/*
|
|
DHT-11 Library
|
|
(c) Created by Charalampos Andrianakis on 18/12/11.
|
|
|
|
Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
of this software and associated documentation files (the "Software"), to deal
|
|
in the Software without restriction, including without limitation the rights
|
|
to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
copies of the Software, and to permit persons to whom the Software is
|
|
furnished to do so, subject to the following conditions:
|
|
|
|
The above copyright notice and this permission notice shall be included in
|
|
all copies or substantial portions of the Software.
|
|
|
|
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
THE SOFTWARE.
|
|
*/
|
|
|
|
#include <avr/io.h>
|
|
#include "contiki.h"
|
|
#include "dht11.h"
|
|
#include "led.h" // debug
|
|
|
|
#define udelay(u) clock_delay_usec(u)
|
|
#define mdelay(u) clock_delay_msec(u)
|
|
|
|
// define for DHT11 else for DHT22, RHT03
|
|
#define DHT11 1
|
|
|
|
uint8_t DHT_Read_Data(uint16_t *temperature, uint16_t *humidity){
|
|
|
|
//data[5] is 8byte table where data come from DHT are stored
|
|
//laststate holds laststate value
|
|
//counter is used to count microSeconds
|
|
uint8_t data[5], laststate = 0, counter = 0, j = 0, i = 0;
|
|
|
|
//Clear array
|
|
data[0] = data[1] = data[2] = data[3] = data[4] = 0;
|
|
|
|
uint8_t volatile sreg;
|
|
sreg = SREG; /* Save status register before disabling interrupts. */
|
|
cli(); /* Disable interrupts. */
|
|
|
|
//Set pin Output
|
|
//Pin High
|
|
DHT_DRIVE();
|
|
mdelay(100); //Wait for 100mS
|
|
|
|
//Send Request Signal
|
|
//Pin Low
|
|
OUTP_0(); //20ms Low
|
|
mdelay(20);
|
|
//Pin High
|
|
OUTP_1();
|
|
udelay(40); //40us High
|
|
|
|
//Set pin Input to read Bus
|
|
//Set pin Input
|
|
DHT_RELEASE();
|
|
laststate=DHT_INP(); //Read Pin value
|
|
|
|
//Repeat for each Transistions
|
|
for (i=0; i<MAXTIMINGS; i++) {
|
|
//While state is the same count microseconds
|
|
//led1_on();
|
|
//led1_off();
|
|
|
|
while (laststate==DHT_INP()) {
|
|
udelay(1);
|
|
counter++;
|
|
if (counter>254) break;
|
|
}
|
|
|
|
if (counter>254) break;
|
|
|
|
//laststate==_BV(DHT_PIN) checks if laststate was High
|
|
//ignore the first 2 transitions which are the DHT Response
|
|
//if (laststate==_BV(DHT_PIN) && (i > 2)) {
|
|
if ((i&0x01) && (i > 2)) {
|
|
//Save bits in segments of bytes
|
|
//Shift data[] value 1 position left
|
|
//Example. 01010100 if we shift it left one time it will be
|
|
//10101000
|
|
|
|
data[j/8]<<=1;
|
|
if (counter >= 15) { //If it was high for more than 40uS
|
|
//led1_on();
|
|
data[j/8]|=1; //it means it is bit '1' so make a logic
|
|
//led1_off();
|
|
} //OR with the value (save it)
|
|
j++; //making an OR by 1 to this value 10101000
|
|
} //we will have the resault 10101001
|
|
//1 in 8-bit binary is 00000001
|
|
//j/8 changes table record every 8 bits which means a byte has been saved
|
|
//so change to next record. 0/8=0 1/8=0 ... 7/8=0 8/8=1 ... 15/8=1 16/8=2
|
|
laststate=DHT_INP(); //save current state
|
|
counter=0; //reset counter
|
|
|
|
}
|
|
SREG = sreg; /* Enable interrupts. */
|
|
//printf("HUM %d %d %d %d %d %d",data[0],data[1],data[2],data[3],data[4],(uint8_t)(data[0] + data[1] + data[2] + data[3]) );
|
|
//Check if data received are correct by checking the CheckSum
|
|
if ((uint8_t)(data[0] + data[1] + data[2] + data[3]) == data[4]) {
|
|
#ifdef DHT11
|
|
*humidity = data[0];
|
|
*temperature = data[2];
|
|
#else
|
|
*humidity = (uint16_t)data[0]<<8 | data[1];
|
|
*temperature = (uint16_t)data[2]<<8 | data[3];
|
|
#endif
|
|
return 0;
|
|
}else{
|
|
*humidity = 2;
|
|
*temperature = 2;
|
|
// uart_puts("\r\nCheck Sum Error");
|
|
}
|
|
|
|
return 0xff; // Check Sum Error
|
|
}
|