147 lines
4.2 KiB
C
147 lines
4.2 KiB
C
/*
|
|
* Copyright (c) 2007, Swedish Institute of Computer Science
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* Device driver for the Sensirion SHT1x/SHT7x family of humidity and
|
|
* temperature sensors.
|
|
*/
|
|
|
|
#include "contiki.h"
|
|
#include <stdio.h>
|
|
#include <dev/servo.h>
|
|
|
|
#define DEBUG 0
|
|
|
|
#if DEBUG
|
|
#include <stdio.h>
|
|
#define PRINTF(...) printf(__VA_ARGS__)
|
|
#else
|
|
#define PRINTF(...)
|
|
#endif
|
|
|
|
/*---------------------------------------------------------------------------*/
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* servo device
|
|
*/
|
|
|
|
#define SERVO_OFFSET 1000
|
|
#define SERVO_MAX 1000
|
|
#define SERVO_INIT 500
|
|
|
|
unsigned int servoa=SERVO_INIT;
|
|
unsigned int servob=SERVO_INIT;
|
|
|
|
void
|
|
servo_init(void)
|
|
{
|
|
// Port B initialization
|
|
// Func7=Out Func6=Out Func5=Out Func4=In Func3=In Func2=In Func1=In Func0=In
|
|
// State7=0 State6=0 State5=0 State4=T State3=T State2=T State1=T State0=T
|
|
PORTB=0x00;
|
|
DDRB=0xE0;
|
|
// Timer/Counter 1 initialization
|
|
// Clock source: System Clock
|
|
// Clock value: 2000.000 kHz
|
|
// Mode: Ph. & fr. cor. PWM top=ICR1
|
|
// OC1A output: Connected
|
|
// OC1B output: Connected
|
|
// OC1C output: Connected
|
|
// Noise Canceler: Off
|
|
// Input Capture on Falling Edge
|
|
// Timer1 Overflow Interrupt: Off
|
|
// Input Capture Interrupt: Off
|
|
// Compare A Match Interrupt: Off
|
|
// Compare B Match Interrupt: Off
|
|
// Compare C Match Interrupt: Off
|
|
TCCR1A=0xA8;
|
|
TCCR1B=0x12;
|
|
TCNT1H=0x00;
|
|
TCNT1L=0x00;
|
|
// ICR1 has a computed value of 20,000 - see the ESawdust.com/blog article for how this
|
|
// value was derived.
|
|
// 20000 == 0x4e20 so that's what goes into the high and low byte of the ICR1 register
|
|
// alternatively, Codevision would let you just do ICR1 = 20000;
|
|
ICR1H=0x4E;
|
|
ICR1L=0x20;
|
|
|
|
/* OCR1AH=0x00;
|
|
OCR1AL=0x00;
|
|
*/
|
|
// OCR1A will govern the steering servo, OCR1B will govern throttle
|
|
OCR1A = 1500; // set it to an initial position somewhere in the middle of the 1 to 2ms range
|
|
|
|
// OCR1A will govern the steering servo, OCR1B will govern throttle
|
|
OCR1B = 1500; // set it to an initial position somewhere in the middle of the 1 to 2ms range
|
|
// start with motor off - no duty cycle at all
|
|
OCR1CH=0x00;
|
|
OCR1CL=0x00;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* Power of device.
|
|
*/
|
|
void
|
|
servo_off(void)
|
|
{
|
|
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* get servo position
|
|
*/
|
|
unsigned int
|
|
servo_get(unsigned int i)
|
|
{
|
|
if(i==0)
|
|
return servoa;
|
|
if(i==1)
|
|
return servob;
|
|
return 0;
|
|
}
|
|
/*---------------------------------------------------------------------------*/
|
|
/*
|
|
* Set servo position
|
|
*/
|
|
unsigned int
|
|
servo_set(unsigned i,unsigned int j)
|
|
{
|
|
if(j > SERVO_MAX)
|
|
j=SERVO_MAX;
|
|
|
|
if(i==0)
|
|
servoa=j;
|
|
OCR1A = SERVO_OFFSET + servoa;
|
|
return 1;
|
|
if(i==1)
|
|
servob=j;
|
|
OCR1A = SERVO_OFFSET + servob;
|
|
return 1;
|
|
}
|