04bbba6c12
Rename guhRF platform to osd-merkur-256, previous osd-merkur platform is now osd-merkur-128. Also check that everything is consistent. Add both platforms to the regression tests. Move redundant files in platform dev directory of both platforms to cpu/avr/dev. Note that this probably needs some rework. Already discovered some inconsistency in io definitions of both devices in the avr/io.h includes. Added a workaround in the obvious cases. The platform makefiles now set correct parameters for bootloader and for reading mac-address from flash memory. Factor the flash programming into cpu/avr and platform/osd-merkur* and rework *all* osd example makefiles to use the new settings. Also update all the flash.sh and run.sh to use the new settings. The suli ledstrip modules (and osd example) have also been removed.
92 lines
2.9 KiB
Makefile
92 lines
2.9 KiB
Makefile
CONTIKI_TARGET_DIRS = . dev apps net loader dev/arduino
|
|
|
|
CONTIKI_CORE=contiki-main
|
|
CONTIKI_TARGET_MAIN = ${CONTIKI_CORE}.o
|
|
CONTIKI_TARGET_SOURCEFILES += contiki-main.c params.c node-id.c
|
|
#Needed for slip
|
|
CONTIKI_TARGET_SOURCEFILES += led.c sensors.c slip_uart0.c slip.c leds-arch.c
|
|
CONTIKI_TARGET_SOURCEFILES += temperature-sensor.c adc.c
|
|
#Needed for Button
|
|
CONTIKI_TARGET_SOURCEFILES += button-sensor.c
|
|
# i2c Master
|
|
#CONTIKI_TARGET_SOURCEFILES += i2c.c
|
|
#Needed for DHT11 humidity sensor
|
|
CONTIKI_TARGET_SOURCEFILES += dht11.c
|
|
#Needed for DS18S20 temperature sensor
|
|
CONTIKI_TARGET_SOURCEFILES += ds1820.c
|
|
#Needed for Battery test
|
|
CONTIKI_TARGET_SOURCEFILES += battery-sensor.c batmon.c
|
|
#Needed for PIR
|
|
CONTIKI_TARGET_SOURCEFILES += pir-sensor.c
|
|
#Needed for OPTRIAC
|
|
CONTIKI_TARGET_SOURCEFILES += optriac-sensor.c
|
|
#Needed for SERVO
|
|
CONTIKI_TARGET_SOURCEFILES += servo.c servo-sensor.c
|
|
#Needed for Timer4 Servo
|
|
#CONTIKI_TARGET_SOURCEFILES += t4-servo.c t4-servo-sensor.c
|
|
#Needed for Relay 1 to 4
|
|
CONTIKI_TARGET_SOURCEFILES += relay.c relay-sensor.c
|
|
# Arduino
|
|
CONTIKI_TARGET_SOURCEFILES += wiring_digital.c
|
|
CONTIKI_TARGET_SOURCEFILES += new.cpp twi.c Wire.cpp WMath.cpp
|
|
CONTIKI_TARGET_SOURCEFILES += Print.cpp Stream.cpp WString.cpp
|
|
# guh Source Files
|
|
# Smart Grid Ready Interface
|
|
CONTIKI_TARGET_SOURCEFILES += sg-ready.c
|
|
|
|
CONTIKIAVR=$(CONTIKI)/cpu/avr
|
|
|
|
CONTIKIBOARD=.
|
|
BOOTLOADER_START = 0x1F000
|
|
CONTIKI_PLAT_DEFS = -DF_CPU=16000000UL -DAUTO_CRC_PADDING=2 -DPLAT_TIMER=5
|
|
|
|
MCU=atmega128rfa1
|
|
|
|
#AVRDUDE_PROGRAMMER=jtag2
|
|
AVRDUDE_PROGRAMMER=arduino
|
|
|
|
# For usb devices, you may either use PORT=usb, or (e.g. if you have
|
|
# more than one programmer connected) you can use the following trick to
|
|
# find out the serial number:
|
|
#
|
|
# The example is for an JTAGICE mkII used to program an ATmega128:
|
|
# avrdude -v -P usb:xxxx -c jtag2 -p atmega128
|
|
# AVRDUDE_PORT=usb:00B000000D79
|
|
# For serial devices with bootloader we also use the AVRDUDE_PORT setting:
|
|
AVRDUDE_PORT=/dev/ttyUSB0
|
|
# Only needed for serial devices, use empty setting for other
|
|
# programmers
|
|
AVRDUDE_BAUD_OPTION=-b 57600
|
|
|
|
# Additional avrdude options
|
|
# First some flash options:
|
|
# Verify off is -V
|
|
# Erase is -e
|
|
# No-Erase (needed by some stk500 variants) is -D
|
|
AVRDUDE_FLASH_OPTIONS=-e
|
|
AVRDUDE_OPTIONS=$(AVRDUDE_BAUD_OPTION) $(AVRDUDE_FLASH_OPTIONS)
|
|
AVRDUDE_MCU=m128rfa1
|
|
|
|
#debug
|
|
# CFLAGS += -save-temps
|
|
# Bootloader bonsai
|
|
# LDFLAGS += -save-temps
|
|
# For the old bonsai bootloader compiled with squeeze gcc-avr we
|
|
# directly used the address of the bootloader:
|
|
#BOOTLOADER_GET_MAC=0x0001f3a0
|
|
# For newer bonsai we have a jump table at the end of the bootloader
|
|
# section:
|
|
BOOTLOADER_GET_MAC=0x0001ff80
|
|
|
|
LDFLAGS += -Wl,--defsym,bootloader_get_mac=$(BOOTLOADER_GET_MAC)
|
|
|
|
|
|
include $(CONTIKIAVR)/Makefile.avr
|
|
include $(CONTIKIAVR)/radio/Makefile.radio
|
|
|
|
MODULES += core/net/mac core/net core/net/mac/sicslowmac \
|
|
core/net/mac/contikimac core/net/llsec \
|
|
# core/net/ipv6 core/net/ipv4 core/net/ip \
|
|
# core/net/rime \
|
|
# core/net/rpl \
|