# Set this to the name of your sketch (without extension .pde) SKETCH=sketch ifeq ($(TARGET), osd-merkur) PLATFORM_FILES= avr-size arduino-example.osd-merkur.hex \ arduino-example.osd-merkur.eep endif all: arduino-example $(PLATFORM_FILES) CONTIKI=../../.. # Contiki IPv6 configuration CONTIKI_WITH_IPV6 = 1 CFLAGS += -DPROJECT_CONF_H=\"project-conf.h\" LFLAGS += -lm PROJECT_SOURCEFILES += ${SKETCH}.cpp Adafruit_HTU21DF.cpp Wire.cpp twi.c new.cpp WString.cpp Stream.cpp # automatically build RESTful resources REST_RESOURCES_DIR = ./resources REST_RESOURCES_DIR_COMMON = ../resources-common REST_RESOURCES_FILES= $(notdir \ $(shell find $(REST_RESOURCES_DIR) -name '*.c') \ $(shell find $(REST_RESOURCES_DIR_COMMON) -name '*.c') \ ) PROJECTDIRS += $(REST_RESOURCES_DIR) $(REST_RESOURCES_DIR_COMMON) PROJECT_SOURCEFILES += $(REST_RESOURCES_FILES) # variable for Makefile.include ifneq ($(TARGET), minimal-net) CFLAGS += -DUIP_CONF_IPV6_RPL=1 else # minimal-net does not support RPL under Linux and is mostly used to test CoAP only ${info INFO: compiling without RPL} CFLAGS += -DUIP_CONF_IPV6_RPL=0 CFLAGS += -DHARD_CODED_ADDRESS=\"fdfd::10\" ${info INFO: compiling with large buffers} CFLAGS += -DUIP_CONF_BUFFER_SIZE=2048 CFLAGS += -DREST_MAX_CHUNK_SIZE=1024 CFLAGS += -DCOAP_MAX_HEADER_SIZE=640 endif # linker optimizations SMALL=1 # REST Engine shall use Erbium CoAP implementation APPS += er-coap APPS += rest-engine APPS += arduino include $(CONTIKI)/Makefile.include include $(CONTIKI)/apps/arduino/Makefile.include avr-size: arduino-example.osd-merkur avr-size -C --mcu=MCU=atmega128rfa1 arduino-example.osd-merkur arduino-example.osd-merkur.hex: arduino-example.osd-merkur avr-objcopy -j .text -j .data -O ihex arduino-example.osd-merkur \ arduino-example.osd-merkur.hex arduino-example.osd-merkur.eep: arduino-example.osd-merkur avr-objcopy -j .eeprom --set-section-flags=.eeprom="alloc,load" \ --change-section-lma .eeprom=0 -O ihex \ arduino-example.osd-merkur arduino-example.osd-merkur.eep flash: arduino-example.osd-merkur.hex arduino-example.osd-merkur.eep avrdude -pm128rfa1 -c arduino -P/dev/ttyUSB0 -b57600 -e -U \ flash:w:arduino-example.osd-merkur.hex:a -U \ eeprom:w:arduino-example.osd-merkur.eep:a .PHONY: flash avr-size $(CONTIKI)/tools/tunslip6: $(CONTIKI)/tools/tunslip6.c (cd $(CONTIKI)/tools && $(MAKE) tunslip6) connect-router: $(CONTIKI)/tools/tunslip6 sudo $(CONTIKI)/tools/tunslip6 aaaa::1/64 connect-router-cooja: $(CONTIKI)/tools/tunslip6 sudo $(CONTIKI)/tools/tunslip6 -a 127.0.0.1 aaaa::1/64 connect-minimal: sudo ip address add fdfd::1/64 dev tap0