/* Copyright (c) 2009, Swedish Institute of Computer Science * All rights reserved. * * Additional fixes for AVR contributed by: * * Colin O'Flynn coflynn@newae.com * Eric Gnoske egnoske@gmail.com * Blake Leverett bleverett@gmail.com * Mike Vidales mavida404@gmail.com * Kevin Brown kbrown3@uccs.edu * Nate Bohlmann nate@elfwerks.com * David Kopf dak664@embarqmail.com * Ivan Delamer delamer@ieee.com * * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * * Neither the name of the copyright holders nor the names of * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * * */ /** * \addtogroup wireless * @{ */ /** * \defgroup hal RF230 hardware level drivers * @{ */ /** * \file * This file contains low-level radio driver code. * This version is optimized for use with the "barebones" RF230bb driver, * which communicates directly with the contiki core MAC layer. * It is optimized for speed at the expense of generality. */ #include "contiki-conf.h" #if DEBUGFLOWSIZE extern uint8_t debugflowsize,debugflow[DEBUGFLOWSIZE]; #define DEBUGFLOW(c) if (debugflowsize<(DEBUGFLOWSIZE-1)) debugflow[debugflowsize++]=c #else #define DEBUGFLOW(c) #endif /*============================ INCLUDE =======================================*/ #include #include "hal.h" #if defined(__AVR_ATmega128RFA1__) #include #include "atmega128rfa1_registermap.h" #else #include "at86rf230_registermap.h" #endif /*============================ VARIABLES =====================================*/ volatile extern signed char rf230_last_rssi; /*============================ CALLBACKS =====================================*/ /*============================ IMPLEMENTATION ================================*/ #if defined(__AVR_ATmega128RFA1__) /* AVR1281 with internal RF231 radio */ #include #elif defined(__AVR__) /* * AVR with hardware SPI tranfers (TODO: move to hw spi hal for avr cpu) */ #include #include #define HAL_SPI_TRANSFER_OPEN() { \ HAL_ENTER_CRITICAL_REGION(); \ HAL_SS_LOW(); /* Start the SPI transaction by pulling the Slave Select low. */ #define HAL_SPI_TRANSFER_WRITE(to_write) (SPDR = (to_write)) #define HAL_SPI_TRANSFER_WAIT() ({while ((SPSR & (1 << SPIF)) == 0) {;}}) /* gcc extension, alternative inline function */ #define HAL_SPI_TRANSFER_READ() (SPDR) #define HAL_SPI_TRANSFER_CLOSE() \ HAL_SS_HIGH(); /* End the transaction by pulling the Slave Select High. */ \ HAL_LEAVE_CRITICAL_REGION(); \ } #define HAL_SPI_TRANSFER(to_write) ( \ HAL_SPI_TRANSFER_WRITE(to_write), \ HAL_SPI_TRANSFER_WAIT(), \ HAL_SPI_TRANSFER_READ() ) #else /* __AVR__ */ /* * Other SPI architecture (parts to core, parts to m16c6Xp */ #include "contiki-mulle.h" // MULLE_ENTER_CRITICAL_REGION // Software SPI transfers #define HAL_SPI_TRANSFER_OPEN() { uint8_t spiTemp; \ HAL_ENTER_CRITICAL_REGION(); \ HAL_SS_LOW(); /* Start the SPI transaction by pulling the Slave Select low. */ #define HAL_SPI_TRANSFER_WRITE(to_write) (spiTemp = spiWrite(to_write)) #define HAL_SPI_TRANSFER_WAIT() ({0;}) #define HAL_SPI_TRANSFER_READ() (spiTemp) #define HAL_SPI_TRANSFER_CLOSE() \ HAL_SS_HIGH(); /* End the transaction by pulling the Slave Select High. */ \ HAL_LEAVE_CRITICAL_REGION(); \ } #define HAL_SPI_TRANSFER(to_write) (spiTemp = spiWrite(to_write)) inline uint8_t spiWrite(uint8_t byte) { uint8_t data = 0; uint8_t mask = 0x80; do { if( (byte & mask) != 0 ) HAL_PORT_MOSI |= (1 << HAL_MOSI_PIN); //call MOSI.set(); else HAL_PORT_MOSI &= ~(1 << HAL_MOSI_PIN); //call MOSI.clr(); if( (HAL_PORT_MISO & (1 << HAL_MISO_PIN)) > 0) //call MISO.get() ) data |= mask; HAL_PORT_SCK &= ~(1 << HAL_SCK_PIN); //call SCLK.clr(); HAL_PORT_SCK |= (1 << HAL_SCK_PIN); //call SCLK.set(); } while( (mask >>= 1) != 0 ); return data; } #endif /* !__AVR__ */ /** \brief This function initializes the Hardware Abstraction Layer. */ #if defined(__AVR_ATmega128RFA1__) void hal_init(void) { /*Reset variables used in file.*/ /* (none at the moment) */ } #elif defined(__AVR__) #define HAL_RF230_ISR() ISR(RADIO_VECT) void hal_init(void) { /*Reset variables used in file.*/ /*IO Specific Initialization - sleep and reset pins. */ /* Set pins low before they are initialized as output? Does not seem to matter */ // hal_set_rst_low(); // hal_set_slptr_low(); DDR_SLP_TR |= (1 << SLP_TR); /* Enable SLP_TR as output. */ DDR_RST |= (1 << RST); /* Enable RST as output. */ /*SPI Specific Initialization.*/ /* Set SS, CLK and MOSI as output. */ /* To avoid a SPI glitch, the port register shall be set before the DDR register */ HAL_PORT_SPI |= (1 << HAL_DD_SS) | (1 << HAL_DD_SCK); /* Set SS and CLK high */ HAL_DDR_SPI |= (1 << HAL_DD_SS) | (1 << HAL_DD_SCK) | (1 << HAL_DD_MOSI); HAL_DDR_SPI &=~ (1<< HAL_DD_MISO); /* MISO input */ /* Run SPI at max speed */ SPCR = (1 << SPE) | (1 << MSTR); /* Enable SPI module and master operation. */ SPSR = (1 << SPI2X); /* Enable doubled SPI speed in master mode. */ /* Enable interrupts from the radio transceiver. */ hal_enable_trx_interrupt(); } #else /* __AVR__ */ #define HAL_RF230_ISR() M16C_INTERRUPT(M16C_INT1) #define HAL_TIME_ISR() M16C_INTERRUPT(M16C_TMRB4) #define HAL_TICK_UPCNT() (0xFFFF-TB4) // TB4 counts down so we need to convert it to upcounting void hal_init(void) { /*Reset variables used in file.*/ /*IO Specific Initialization - sleep and reset pins. */ DDR_SLP_TR |= (1 << SLP_TR); /* Enable SLP_TR as output. */ DDR_RST |= (1 << RST); /* Enable RST as output. */ /*SPI Specific Initialization.*/ /* Set SS, CLK and MOSI as output. */ HAL_DDR_SS |= (1 << HAL_SS_PIN); HAL_DDR_SCK |= (1 << HAL_SCK_PIN); HAL_DDR_MOSI |= (1 << HAL_MOSI_PIN); HAL_DDR_MISO &= ~(1 << HAL_MISO_PIN); /* Set SS */ HAL_PORT_SS |= (1 << HAL_SS_PIN); // HAL_SS_HIGH() HAL_PORT_SCK &= ~(1 << HAL_SCK_PIN); // SCLK.clr() /*TIMER Specific Initialization.*/ // Init count source (Timer B3) TB3 = ((16*10) - 1); // 16 us ticks TB3MR.BYTE = 0b00000000; // Timer mode, F1 TBSR.BIT.TB3S = 1; // Start Timer B3 TB4 = 0xFFFF; // TB4MR.BYTE = 0b10000001; // Counter mode, count TB3 TBSR.BIT.TB4S = 1; // Start Timer B4 INT1IC.BIT.POL = 1; // Select rising edge HAL_ENABLE_OVERFLOW_INTERRUPT(); /* Enable Timer overflow interrupt. */ /* Enable interrupts from the radio transceiver. */ hal_enable_trx_interrupt(); } #endif /* !__AVR__ */ #if defined(__AVR_ATmega128RFA1__) /* Hack for internal radio registers. hal_register_read and hal_register_write are handled through defines, but the preprocesser can't parse a macro containing another #define with multiple arguments, e.g. using #define hal_subregister_read( address, mask, position ) (address&mask)>>position #define SR_TRX_STATUS TRX_STATUS, 0x1f, 0 the following only sees 1 argument to the macro return hal_subregister_read(SR_TRX_STATUS); Possible fix is through two defines: #define x_hal_subregister_read(x) hal_subregister_read(x); #define hal_subregister_read( address, mask, position ) (address&mask)>>position but the subregister defines in atmega128rfa1_registermap.h are currently set up without the _SFR_MEM8 attribute, for use by hal_subregister_write. */ uint8_t hal_subregister_read(uint16_t address, uint8_t mask, uint8_t position) { return (_SFR_MEM8(address)&mask)>>position; } void hal_subregister_write(uint16_t address, uint8_t mask, uint8_t position, uint8_t value) { HAL_ENTER_CRITICAL_REGION(); uint8_t register_value = _SFR_MEM8(address); register_value &= ~mask; value <<= position; value &= mask; value |= register_value; _SFR_MEM8(address) = value; HAL_LEAVE_CRITICAL_REGION(); } #else /* defined(__AVR_ATmega128RFA1__) */ /*----------------------------------------------------------------------------*/ /** \brief This function reads data from one of the radio transceiver's registers. * * \param address Register address to read from. See datasheet for register * map. * * \see Look at the at86rf230_registermap.h file for register address definitions. * * \returns The actual value of the read register. */ uint8_t hal_register_read(uint8_t address) { uint8_t register_value; /* Add the register read command to the register address. */ /* Address should be < 0x2f so no need to mask */ // address &= 0x3f; address |= 0x80; HAL_SPI_TRANSFER_OPEN(); /*Send Register address and read register content.*/ HAL_SPI_TRANSFER(address); register_value = HAL_SPI_TRANSFER(0); HAL_SPI_TRANSFER_CLOSE(); return register_value; } /*----------------------------------------------------------------------------*/ /** \brief This function writes a new value to one of the radio transceiver's * registers. * * \see Look at the at86rf230_registermap.h file for register address definitions. * * \param address Address of register to write. * \param value Value to write. */ void hal_register_write(uint8_t address, uint8_t value) { /* Add the Register Write (short mode) command to the address. */ address = 0xc0 | address; HAL_SPI_TRANSFER_OPEN(); /*Send Register address and write register content.*/ HAL_SPI_TRANSFER(address); HAL_SPI_TRANSFER(value); HAL_SPI_TRANSFER_CLOSE(); } /*----------------------------------------------------------------------------*/ /** \brief This function reads the value of a specific subregister. * * \see Look at the at86rf230_registermap.h file for register and subregister * definitions. * * \param address Main register's address. * \param mask Bit mask of the subregister. * \param position Bit position of the subregister * \retval Value of the read subregister. */ uint8_t hal_subregister_read(uint8_t address, uint8_t mask, uint8_t position) { /* Read current register value and mask out subregister. */ uint8_t register_value = hal_register_read(address); register_value &= mask; register_value >>= position; /* Align subregister value. */ return register_value; } /*----------------------------------------------------------------------------*/ /** \brief This function writes a new value to one of the radio transceiver's * subregisters. * * \see Look at the at86rf230_registermap.h file for register and subregister * definitions. * * \param address Main register's address. * \param mask Bit mask of the subregister. * \param position Bit position of the subregister * \param value Value to write into the subregister. */ void hal_subregister_write(uint8_t address, uint8_t mask, uint8_t position, uint8_t value) { /* Read current register value and mask area outside the subregister. */ volatile uint8_t register_value = hal_register_read(address); register_value &= ~mask; /* Start preparing the new subregister value. shift in place and mask. */ value <<= position; value &= mask; value |= register_value; /* Set the new subregister value. */ /* Write the modified register value. */ hal_register_write(address, value); } #endif /* defined(__AVR_ATmega128RFA1__) */ /*----------------------------------------------------------------------------*/ /** \brief Transfer a frame from the radio transceiver to a RAM buffer * * This version is optimized for use with contiki RF230BB driver. * The callback routine and CRC are left out for speed in reading the rx buffer. * Any delays here can lead to overwrites by the next packet! * * If the frame length is out of the defined bounds, the length, lqi and crc * are set to zero. * * \param rx_frame Pointer to the data structure where the frame is stored. */ void hal_frame_read(hal_rx_frame_t *rx_frame) { #if defined(__AVR_ATmega128RFA1__) uint8_t frame_length,*rx_data,*rx_buffer; /* Get length from the TXT_RX_LENGTH register, not including LQI * Bypassing the length check can result in overrun if buffer is < 256 bytes. */ frame_length = TST_RX_LENGTH; if ((frame_length < HAL_MIN_FRAME_LENGTH) || (frame_length > HAL_MAX_FRAME_LENGTH)) { /* Length test failed */ rx_frame->length = 0; rx_frame->lqi = 0; rx_frame->crc = false; return; } rx_frame->length = frame_length; /* Start of buffer in I/O space, pointer to RAM buffer */ rx_buffer=(uint8_t *)0x180; rx_data = (rx_frame->data); do{ *rx_data++ = _SFR_MEM8(rx_buffer++); } while (--frame_length > 0); /*Read LQI value for this frame.*/ rx_frame->lqi = *rx_buffer; /* If crc was calculated set crc field in hal_rx_frame_t accordingly. * Else show the crc has passed the hardware check. */ rx_frame->crc = true; #else /* defined(__AVR_ATmega128RFA1__) */ uint8_t frame_length, *rx_data; /*Send frame read (long mode) command.*/ HAL_SPI_TRANSFER_OPEN(); HAL_SPI_TRANSFER(0x20); /*Read frame length. This includes the checksum. */ frame_length = HAL_SPI_TRANSFER(0); /*Check for correct frame length. Bypassing this test can result in a buffer overrun! */ if ((frame_length < HAL_MIN_FRAME_LENGTH) || (frame_length > HAL_MAX_FRAME_LENGTH)) { /* Length test failed */ rx_frame->length = 0; rx_frame->lqi = 0; rx_frame->crc = false; } else { rx_data = (rx_frame->data); rx_frame->length = frame_length; /*Transfer frame buffer to RAM buffer */ HAL_SPI_TRANSFER_WRITE(0); HAL_SPI_TRANSFER_WAIT(); do{ *rx_data++ = HAL_SPI_TRANSFER_READ(); HAL_SPI_TRANSFER_WRITE(0); /* CRC was checked in hardware, but redoing the checksum here ensures the rx buffer * is not being overwritten by the next packet. Since that lengthy computation makes * such overwrites more likely, we skip it and hope for the best. * Without the check a full buffer is read in 320us at 2x spi clocking. * The 802.15.4 standard requires 640us after a greater than 18 byte frame. * With a low interrupt latency overwrites should never occur. */ // crc = _crc_ccitt_update(crc, tempData); HAL_SPI_TRANSFER_WAIT(); } while (--frame_length > 0); /*Read LQI value for this frame.*/ rx_frame->lqi = HAL_SPI_TRANSFER_READ(); /* If crc was calculated set crc field in hal_rx_frame_t accordingly. * Else show the crc has passed the hardware check. */ rx_frame->crc = true; } HAL_SPI_TRANSFER_CLOSE(); #endif /* defined(__AVR_ATmega128RFA1__) */ } /*----------------------------------------------------------------------------*/ /** \brief This function will download a frame to the radio transceiver's frame * buffer. * * \param write_buffer Pointer to data that is to be written to frame buffer. * \param length Length of data. The maximum length is 127 bytes. */ void hal_frame_write(uint8_t *write_buffer, uint8_t length) { #if defined(__AVR_ATmega128RFA1__) uint8_t *tx_buffer; tx_buffer=(uint8_t *)0x180; //start of fifo in i/o space /* Write frame length, including the two byte checksum */ /* The top bit of the length field shall be set to 0 for IEEE 802.15.4 compliant frames */ /* It should already be clear, so bypassing the masking is sanity check of the uip stack */ // length &= 0x7f; _SFR_MEM8(tx_buffer++) = length; /* Download to the Frame Buffer. * When the FCS is autogenerated there is no need to transfer the last two bytes * since they will be overwritten. */ #if !RF230_CONF_CHECKSUM length -= 2; #endif do _SFR_MEM8(tx_buffer++)= *write_buffer++; while (--length); #else /* defined(__AVR_ATmega128RFA1__) */ /* Optionally truncate length to maximum frame length. * Not doing this is a fast way to know when the application needs fixing! */ // length &= 0x7f; HAL_SPI_TRANSFER_OPEN(); /* Send Frame Transmit (long mode) command and frame length */ HAL_SPI_TRANSFER(0x60); HAL_SPI_TRANSFER(length); /* Download to the Frame Buffer. * When the FCS is autogenerated there is no need to transfer the last two bytes * since they will be overwritten. */ #if !RF230_CONF_CHECKSUM length -= 2; #endif do HAL_SPI_TRANSFER(*write_buffer++); while (--length); HAL_SPI_TRANSFER_CLOSE(); #endif /* defined(__AVR_ATmega128RFA1__) */ } /*----------------------------------------------------------------------------*/ #if 0 //Uses 80 bytes (on Raven) omit unless needed /** \brief Read SRAM * * This function reads from the SRAM of the radio transceiver. * * \param address Address in the TRX's SRAM where the read burst should start * \param length Length of the read burst * \param data Pointer to buffer where data is stored. */ void hal_sram_read(uint8_t address, uint8_t length, uint8_t *data) { HAL_SPI_TRANSFER_OPEN(); /*Send SRAM read command and address to start*/ HAL_SPI_TRANSFER(0x00); HAL_SPI_TRANSFER(address); HAL_SPI_TRANSFER_WRITE(0); HAL_SPI_TRANSFER_WAIT(); /*Upload the chosen memory area.*/ do{ *data++ = HAL_SPI_TRANSFER_READ(); HAL_SPI_TRANSFER_WRITE(0); HAL_SPI_TRANSFER_WAIT(); } while (--length > 0); HAL_SPI_TRANSFER_CLOSE(); } #endif /*----------------------------------------------------------------------------*/ #if 0 //omit unless needed /** \brief Write SRAM * * This function writes into the SRAM of the radio transceiver. It can reduce * SPI transfers if only part of a frame is to be changed before retransmission. * * \param address Address in the TRX's SRAM where the write burst should start * \param length Length of the write burst * \param data Pointer to an array of bytes that should be written */ void hal_sram_write(uint8_t address, uint8_t length, uint8_t *data) { HAL_SPI_TRANSFER_OPEN(); /*Send SRAM write command.*/ HAL_SPI_TRANSFER(0x40); /*Send address where to start writing to.*/ HAL_SPI_TRANSFER(address); /*Upload the chosen memory area.*/ do{ HAL_SPI_TRANSFER(*data++); } while (--length > 0); HAL_SPI_TRANSFER_CLOSE(); } #endif /*----------------------------------------------------------------------------*/ /* This #if compile switch is used to provide a "standard" function body for the */ /* doxygen documentation. */ #if defined(DOXYGEN) /** \brief ISR for the radio IRQ line, triggered by the input capture. * This is the interrupt service routine for timer1.ICIE1 input capture. * It is triggered of a rising edge on the radio transceivers IRQ line. */ void RADIO_VECT(void); #else /* !DOXYGEN */ /* These link to the RF230BB driver in rf230.c */ void rf230_interrupt(void); extern hal_rx_frame_t rxframe[RF230_CONF_RX_BUFFERS]; extern uint8_t rxframe_head,rxframe_tail; /* rf230interruptflag can be printed in the main idle loop for debugging */ #define DEBUG 0 #if DEBUG volatile char rf230interruptflag; #define INTERRUPTDEBUG(arg) rf230interruptflag=arg #else #define INTERRUPTDEBUG(arg) #endif #if defined(__AVR_ATmega128RFA1__) /* The atmega128rfa1 has individual interrupts for the integrated radio' * Whichever are enabled by the RF230 driver must be present even if not used! */ /* Received packet interrupt */ ISR(TRX24_RX_END_vect) { /* Get the rssi from ED if extended mode */ #if RF230_CONF_AUTOACK rf230_last_rssi=hal_register_read(RG_PHY_ED_LEVEL); #endif /* Buffer the frame and call rf230_interrupt to schedule poll for rf230 receive process */ /* Is a ram buffer available? */ if (rxframe[rxframe_tail].length) {DEBUGFLOW('0');} else /*DEBUGFLOW('1')*/; #ifdef RF230_MIN_RX_POWER /* Discard packets weaker than the minimum if defined. This is for testing miniature meshes */ /* This does not prevent an autoack. TODO:rfa1 radio can be set up to not autoack weak packets */ if (rf230_last_rssi >= RF230_MIN_RX_POWER) { #else if (1) { #endif // DEBUGFLOW('2'); hal_frame_read(&rxframe[rxframe_tail]); rxframe_tail++;if (rxframe_tail >= RF230_CONF_RX_BUFFERS) rxframe_tail=0; rf230_interrupt(); } } /* Preamble detected, starting frame reception */ ISR(TRX24_RX_START_vect) { // DEBUGFLOW('3'); /* Save RSSI for this packet if not in extended mode, scaling to 1dB resolution */ #if !RF230_CONF_AUTOACK rf230_last_rssi = 3 * hal_subregister_read(SR_RSSI); #endif } /* PLL has locked, either from a transition out of TRX_OFF or a channel change while on */ ISR(TRX24_PLL_LOCK_vect) { // DEBUGFLOW('4'); } /* PLL has unexpectedly unlocked */ ISR(TRX24_PLL_UNLOCK_vect) { DEBUGFLOW('5'); } /* Flag is set by the following interrupts */ extern volatile uint8_t rf230_wakewait, rf230_txendwait,rf230_ccawait; /* Wake has finished */ ISR(TRX24_AWAKE_vect) { // DEBUGFLOW('6'); rf230_wakewait=0; } /* Transmission has ended */ ISR(TRX24_TX_END_vect) { // DEBUGFLOW('7'); rf230_txendwait=0; } //extern volatile uint8_t rf230_pending; /* Frame address has matched ours */ ISR(TRX24_XAH_AMI_vect) { // DEBUGFLOW('8'); // rf230_pending=1; } /* CCAED measurement has completed */ ISR(TRX24_CCA_ED_DONE_vect) { DEBUGFLOW('4'); rf230_ccawait=0; } #else /* defined(__AVR_ATmega128RFA1__) */ /* Separate RF230 has a single radio interrupt and the source must be read from the IRQ_STATUS register */ HAL_RF230_ISR() { volatile uint8_t state; uint8_t interrupt_source; /* used after HAL_SPI_TRANSFER_OPEN/CLOSE block */ INTERRUPTDEBUG(1); /* Using SPI bus from ISR is generally a bad idea... */ /* Note: all IRQ are not always automatically disabled when running in ISR */ HAL_SPI_TRANSFER_OPEN(); /*Read Interrupt source.*/ /*Send Register address and read register content.*/ HAL_SPI_TRANSFER_WRITE(0x80 | RG_IRQ_STATUS); HAL_SPI_TRANSFER_WAIT(); /* AFTER possible interleaved processing */ interrupt_source = HAL_SPI_TRANSFER(0); HAL_SPI_TRANSFER_CLOSE(); /*Handle the incomming interrupt. Prioritized.*/ if ((interrupt_source & HAL_RX_START_MASK)){ INTERRUPTDEBUG(10); /* Save RSSI for this packet if not in extended mode, scaling to 1dB resolution */ #if !RF230_CONF_AUTOACK #if 0 // 3-clock shift and add is faster on machines with no hardware multiply // With -Os avr-gcc saves a byte by using the general routine for multiply by 3 rf230_last_rssi = hal_subregister_read(SR_RSSI); rf230_last_rssi = (rf230_last_rssi <<1) + rf230_last_rssi; #else // Faster with 1-clock multiply. Raven and Jackdaw have 2-clock multiply so same speed while saving 2 bytes of program memory rf230_last_rssi = 3 * hal_subregister_read(SR_RSSI); #endif #endif } else if (interrupt_source & HAL_TRX_END_MASK){ INTERRUPTDEBUG(11); state = hal_subregister_read(SR_TRX_STATUS); if((state == BUSY_RX_AACK) || (state == RX_ON) || (state == BUSY_RX) || (state == RX_AACK_ON)){ /* Received packet interrupt */ /* Buffer the frame and call rf230_interrupt to schedule poll for rf230 receive process */ if (rxframe[rxframe_tail].length) INTERRUPTDEBUG(42); else INTERRUPTDEBUG(12); #ifdef RF230_MIN_RX_POWER /* Discard packets weaker than the minimum if defined. This is for testing miniature meshes.*/ /* Save the rssi for printing in the main loop */ #if RF230_CONF_AUTOACK //rf230_last_rssi=hal_subregister_read(SR_ED_LEVEL); rf230_last_rssi=hal_register_read(RG_PHY_ED_LEVEL); #endif if (rf230_last_rssi >= RF230_MIN_RX_POWER) { #endif hal_frame_read(&rxframe[rxframe_tail]); rxframe_tail++;if (rxframe_tail >= RF230_CONF_RX_BUFFERS) rxframe_tail=0; rf230_interrupt(); #ifdef RF230_MIN_RX_POWER } #endif } } else if (interrupt_source & HAL_TRX_UR_MASK){ INTERRUPTDEBUG(13); ; } else if (interrupt_source & HAL_PLL_UNLOCK_MASK){ INTERRUPTDEBUG(14); ; } else if (interrupt_source & HAL_PLL_LOCK_MASK){ INTERRUPTDEBUG(15); ; } else if (interrupt_source & HAL_BAT_LOW_MASK){ /* Disable BAT_LOW interrupt to prevent endless interrupts. The interrupt */ /* will continously be asserted while the supply voltage is less than the */ /* user-defined voltage threshold. */ uint8_t trx_isr_mask = hal_register_read(RG_IRQ_MASK); trx_isr_mask &= ~HAL_BAT_LOW_MASK; hal_register_write(RG_IRQ_MASK, trx_isr_mask); INTERRUPTDEBUG(16); ; } else { INTERRUPTDEBUG(99); ; } } #endif /* defined(__AVR_ATmega128RFA1__) */ # endif /* defined(DOXYGEN) */ /** @} */ /** @} */ /*EOF*/