/*
 *     \mainpage ATmega3290p LCD Driver Software for Raven
*/
/**
 *     \image html raven.png
 *     \ingroup platform
 *     \defgroup lcdraven RZRAVEN LCD 3290p
 *
 *     \section intro_lcd LCD Introduction
 *
 *  This Raven LCD Driver application software was designed for a user interface
 *  to the Contiki 6LoWPAN collaboration on board the ATmega3290p. The
 *  LCD functionality uses the binary command set described in the release notes.
 *  These binary commands can also be found in a list of main.h.
 *
 *     \section compile_lcd Compiling Raven LCD Driver
 *
 *  Raven LCD Driver can be compiled on the following platforms:
 *
 *   -# <b>WinAvr + AVR Studio (AVR-GCC).</b>  The @b ravenlcd_3290.aps file is used by AVR
 *      Studio.  If you have WinAVR and AVR Studio installed, ravenlcd can be
 *      compiled and developed using free tools.  The Makefile.avr-ravenlcd is not
 *      used with AVR Studio.
 *   -# <b>AVR-GCC on Linux.</b>  The <b>Makefile.avr-ravenlcd</b> file is to be used for Linux.
 *      Be sure you have a recent toolchain installed, including patches
 *      required for GCC/avr-libc to recognize new devices.  The avr-libc
 *      webpage includes a concise guide on how to patch and build the AVR
 *      toolchain.
 *
 *     \section fuses_lcd Board fuse settings
 *
 *  The Raven LCD (3290p device) requires the proper fuse settings to function
 *  properly. These settings have been summarized below:
 *   -# Raven LCD (3290p device)
 *      -# Extended: <b>0xFF</b> (No Brown Out)
 *      -# High: <b>0x99</b> (JTAG and ISP enabled, No OCDEN or EEPROM saving required)
 *      -# Low: <b>0xE2</b> (Use Int RC OSC - Start-up Time:6CK + 65ms)
 *
 *     \section notes_lcd Operation Release Notes
 *
 *  After programming the Raven LCD 3290p with the proper image, you will be introduced to
 *  the menu in the picture below:
 *
 *     \image html contiki_menu_3290.jpg
 *
 *  Operating the menu requires that the matching command set has been programmed into
 *  the ATmega1284 application. This will allow the menu to communicate properly and control the
 *  Contiki 6LoWPAN applcation.
 *
 *  During normal operation, you will need to make note of these <b>IMPORTANT</b> operating instructions:
 *   -# <b>Temp Sensor</b> - The temperature sensor shares the same GPIO as the JTAG interface for the 3290p.
 *   This requires the JTAG feature to be <b>disabled</b> in order to have proper temperature readings.
 *   -# <b>Debug Menu</b> - The DEBUG menu setting is used to configure this JTAG feature.
 *      -# If the JTAG feature is enabled during a temperature reading attempt,
 *      the menu will signal a <b>caution</b> symbol to the user letting them know the JTAG
 *      feature needs to be disabled.
 *     \image html caution.gif
 *      -# The JTAG header may also need to be physically disconnected from any external
 *      programming/debugging device in order to obtain correct temperature readings.
 *   -# <b>Temp Data</b> - Once the temperature reading is proper, the user can send this reading
 *   to the webserver for Sensor Reading Data (<b>Once</b> or <b>Auto</b>). The webserver will
 *   only update the html data when <b>refreshed</b>.
 *   -# <b>EXT_SUPL_SIG</b> - This signal connects the external supply voltage to ADC2 through a divider.
 *   Enabling MEASURE_ADC2 in temp.h causes it to be sampled and sent to the webserver along
 *   with the temperature.
 *
 *   More information about the operation of the Contiki 6LoWPAN system can be found
 *   at the \ref tutorialraven.
 *
 *   More information about the 802.15.4 MAC designed for the Contiki 6LoWPAN system
 *   can be found at the \ref macdoc.
 *
 *     \section binary_lcd Binary Command Description
 *
 *  Using the binary commmand list described in main.h, the 3290p will contruct a binary
 *  command serial frame to control the 1284p. An example command frame is contructed below:
 *   -# <b>0x01,0x01,0x81,0x01,0x04</b> - Send Ping Request number 1 to 1284p
 *       -# <b>0x01</b> - Start of binary command frame
 *       -# <b>0x01</b> - Length of binary command payload
 *       -# <b>0x81</b> - Binary command SEND_PING
 *       -# <b>0x01</b> - Payload value (eg. ping Request number 1)
 *       -# <b>0x04</b> - End of binary command frame
 *
 *  The following commands are used to control the 1284p.
 *   -# <b>SEND_TEMP - (0x80)</b>
 *   -# <b>SEND_PING - (0x81)</b>
 *...-# <b>SEND_SLEEP- (0x82)</b>
 *...-# <b>SEND_WAKE - (0x83)</b>
 *
 *  The following commands are used to update the 3290p.
 *   -# <b>REPORT_PING      - (0xC0)</b>
 *   -# <b>REPORT_PING_BEEP - (0xC1)</b>
 *   -# <b>REPORT_TEXT_MSG  - (0xC2)</b>
 *   -# <b>REPORT_WAKE      - (0xC3)</b>
*/
/*
 *  Copyright (c) 2008  Swedish Institute of Computer Science
 *  All rights reserved.
 *
 *  Redistribution and use in source and binary forms, with or without
 *  modification, are permitted provided that the following conditions are met:
 *
 *  * Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *  * Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 *  * Neither the name of the copyright holders nor the names of
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */
/**
 * \file
 *
 * \brief
 *      This is the main file for the Raven LCD application.
 *
 * \author
 *      Mike Vidales mavida404@gmail.com
 *
 */

#include "lcd.h"
#include "key.h"
#include "main.h"
#include "uart.h"
#include "timer.h"
#include "menu.h"
#include "temp.h"

#include <avr/io.h>
#include <avr/fuse.h>
FUSES =
	{
		.low = 0xe2,
		.high = 0x99,
		.extended = 0xff,
	};


/** \ingroup lcdraven
    \defgroup lcd LCD Functions and data
 *  \{
*/

#if defined( DOXYGEN )
const char menu_text0[];
const char menu_text1[];
const char menu_text2[];
const char menu_text3[];
const char menu_text4[];
const char menu_text5[];
const char menu_text6[];
const char menu_text7[];
const char menu_text8[];
const char menu_text9[];
const char menu_text10[];
const char menu_text11[];
const char menu_text12[];
const char menu_text13[];
const char menu_text14[];
const char menu_text15[];
const char menu_text16[];
const char menu_text17[];
const tmenu_item menu_items[18];
#else  /* !DOXYGEN */
/** \brief This is the menu text in Flash. See menu_items[] for menu operation. */
const char menu_text0[] PROGMEM =  "CONTIKI";
const char menu_text1[] PROGMEM =  "6LOWPAN";
const char menu_text2[] PROGMEM =  "PING";
const char menu_text3[] PROGMEM =  "PINGING";
const char menu_text4[] PROGMEM =  "TEMP";
const char menu_text5[] PROGMEM =  "MODE ";
const char menu_text6[] PROGMEM =  "DEG F";
const char menu_text7[] PROGMEM =  "DEG C";
const char menu_text8[] PROGMEM =  "SEND";
const char menu_text9[] PROGMEM =  "ONCE";
const char menu_text10[] PROGMEM = "AUTO";
const char menu_text11[] PROGMEM = "DEBUG";
const char menu_text12[] PROGMEM = "DBG ON";
const char menu_text13[] PROGMEM = "DBG OFF";
const char menu_text14[] PROGMEM = "SENT";
const char menu_text15[] PROGMEM = "SENDING";
const char menu_text16[] PROGMEM = "SLEEP";
const char menu_text17[] PROGMEM = "DOZE";

/*---------------------------------------------------------------------------*/

/**
 *   \brief Menus for user interface
 *
 *   This constructs the Raven 3290p menu for the Contiki and 6lowpan collaboration. This
 *   follows the struct description of tmenu_item.
 *
 *   { text, left, right, up, down, *state, tmenufunc enter_func}
*/
const PROGMEM tmenu_item menu_items[18]  = {
    {menu_text0,   0,  2,  0,  0, 0,                       0                  },
    {menu_text1,   0,  2,  0,  0, 0,                       0                  },
    {menu_text2,   0,  3, 17,  4, 0,                       menu_ping_request  },
    {menu_text3,   2,  2,  2,  2, 0,                       0                  },
    {menu_text4,   0,  5,  2, 11, 0,                       0                  },
    {menu_text5,   4,  6,  8,  8, 0,                       0                  },
    {menu_text6,   5,  5,  7,  7, (uint8_t*)1,             menu_read_temp     },
    {menu_text7,   5,  5,  6,  6, (uint8_t*)0,             menu_read_temp     },
    {menu_text8,   4,  9,  5,  5, 0,                       0                  },
    {menu_text9,   8, 14, 10, 10, (uint8_t*)0,             menu_prepare_temp  },
    {menu_text10,  8, 15,  9,  9, (uint8_t*)1,             menu_prepare_temp  },
    {menu_text11,  0, 12,  4, 16, 0,                       0                  },
    {menu_text12, 11, 11, 13, 13, (uint8_t*)1,             menu_debug_mode    },
    {menu_text13, 11, 11, 12, 12, (uint8_t*)0,             menu_debug_mode    },
    {menu_text14, 9,  14, 14, 14, 0,                       0                  },
    {menu_text15, 10, 15, 15, 15, 0,                       0                  },
 //   {menu_text16,  0, 16, 11, 17, (uint8_t*)&menu_text16,  menu_run_sleep     },
 //   {menu_text17,  0, 17, 16,  2, (uint8_t*)&menu_text17,  menu_run_doze      },
    {menu_text16,  0, 16, 11, 17, (uint8_t*)1,  menu_run_sleep     },//display "sleep" on wake
    {menu_text17,  0, 17, 16,  2, (uint8_t*)1,  menu_run_doze      },//display "doze" on wake
};
#endif /* !DOXYGEN */

key_state_t button=KEY_STATE_NO_KEY;
tmenu_item menu;
uint8_t count;
uint8_t timeout_count;

/*---------------------------------------------------------------------------*/

/**
 *   \brief This will read the menu_items[] from the index requested.
 *
 *   \param ndx Position index of menu_items[] lookup.
*/
void
read_menu(uint8_t ndx)
{
    /* Reads menu structure from Flash area */
    uint8_t i;
    uint8_t *src = (uint8_t*)&menu_items[ndx];
    uint8_t *dest = (uint8_t*)&menu;

    for (i=0;i<sizeof(tmenu_item);i++){
        *dest++ = pgm_read_byte(src+i);
    }
}

/*---------------------------------------------------------------------------*/

/**
 *   \brief This will toggle the CONTIKI and 6LOWPAN LCD menus in the main
 *   menu position, unless alternate text has been sent from the 1284p.
 *   The other menus will display normally.
*/
char top_menu_text[20];
void
check_main_menu(void)
{
uint8_t showtop=0;

    if(menu.text == menu_text0){
        read_menu(1);
        showtop=1;
    }
    else if(menu.text == menu_text1){
        read_menu(0);
        showtop=1;
    }
    if (showtop) {
        if (top_menu_text[0]) {
            lcd_puts(top_menu_text);
            return;
        }
    }
    lcd_puts_P(menu.text);
}

/*---------------------------------------------------------------------------*/

/**
 *   \brief This will check for the temp menu screen to determine if we need to
 *   clear the 4 digit LCD segments or stop an auto temp send. Also check for
 *   stopping a ping request.
*/
void
check_menu(void)
{
    if(menu.text == menu_text4){
        menu_clear_temp();
    }

    if(menu.text == menu_text10){
        menu_stop_temp();
    }

    if(menu.text == menu_text2){
        menu_stop_ping();
        lcd_num_clr();
    }
}

/*---------------------------------------------------------------------------*/

/**
 *   \brief This is main...
*/
int
main(void)
{
    lcd_init();

    key_init();

    uart_init();

    eeprom_init();

    temp_init();

    timer_init();

    sei();

    lcd_symbol_set(LCD_SYMBOL_RAVEN);
    lcd_symbol_set(LCD_SYMBOL_IP);

    /* Start with main menu */
    read_menu(0);
    /* and draw it */
    lcd_puts_P(menu.text);

    timer_start();

    for (;;){
        /* Make sure interrupts are always on */
        sei();

        /* The one second timer has fired. */
        if(timer_flag){
            timer_flag = false;
            /* Check if main menu needs toggled. */
            check_main_menu();
            /* Update LCD with temp data. */
            if(temp_flag){
                menu_display_temp();
            }
            /* Auto send temp data to 1284p. */
            if(auto_temp){
                menu_send_temp();
            }
            /* If ping mode, send 4 ping requests and then stop. */
            if(ping_mode){
                if((PING_ATTEMPTS == count) && !timeout_flag){
                    count = 0;
                    timeout_count = 0;
                    menu_stop_ping();
                }
                else if(timeout_flag){
                    timeout_flag = false;
                    timeout_count++;
                    /* Display timeout message if all PING_ATTEMPTS were not successful. */
                    if(PING_ATTEMPTS == timeout_count){
                        lcd_puts_P(PSTR("PINGS FAILED"));
                    }
                }
                else{
                    count = menu_send_ping();
                }
            }
        }

        /* Check for button press and deal with it */
        if (is_button()){
            /* Dispatch the button pressed */
            switch (get_button()){
                case KEY_UP:
                    read_menu(menu.up);
                    lcd_puts_P(menu.text);
                    break;
                case KEY_DOWN:
                    read_menu(menu.down);
                    lcd_puts_P(menu.text);
                    break;
                case KEY_LEFT:
                    read_menu(menu.left);
                    lcd_puts_P(menu.text);
                    break;
                case KEY_RIGHT:
                    /*
                     * Check to see if we should show another menu or
                     * run a function
                     */
                    if (!menu.enter_func){
                        /* Just another menu to display */
                        read_menu(menu.right);
                        lcd_puts_P(menu.text);
                        break;
                    }
                    /* Drop through here */
                case KEY_ENTER:
                    /* Call the menu function on right or enter buttons */
                    if (menu.enter_func){
                        menu.enter_func(menu.state);
                        if (menu.state){
                            /*
                             * We just called a selection menu (not a test),
                             * so re-display the text for this menu level
                             */
                            lcd_puts_P(menu.text);
                        }
                        /* After enter key, check the right button menu and display. */
                        read_menu(menu.right);
                        lcd_puts_P(menu.text);
                    }
                    break;
                default:
                    break;
            }
            /* After button press, check for menus... */
            check_menu();
        }
        /* Process any progress frames */
        uart_serial_rcv_frame(false);
    } /* end for(). */
} /* end main(). */

/** \} */