/* * Copyright (c) 2014, Texas Instruments Incorporated - http://www.ti.com/ * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. Neither the name of the copyright holder nor the names of its * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED * OF THE POSSIBILITY OF SUCH DAMAGE. */ /*---------------------------------------------------------------------------*/ /** * \addtogroup cc26xx-rf * @{ * * \file * Implementation of the CC26xx RF driver */ /*---------------------------------------------------------------------------*/ #include "contiki.h" #include "dev/radio.h" #include "dev/cc26xx-rf.h" #include "dev/oscillators.h" #include "net/packetbuf.h" #include "net/rime/rimestats.h" #include "net/linkaddr.h" #include "net/netstack.h" #include "sys/energest.h" #include "sys/clock.h" #include "sys/rtimer.h" #include "lpm.h" #include "ti-lib.h" /*---------------------------------------------------------------------------*/ /* RF core and RF HAL API */ #include "hw_rfc_dbell.h" #include "hw_rfc_pwr.h" /*---------------------------------------------------------------------------*/ /* RF Core Mailbox API */ #include "mailbox.h" #include "common_cmd.h" #include "common_cmd_field.h" #include "ble_cmd.h" #include "ble_cmd_field.h" #include "ieee_cmd.h" #include "ieee_cmd_field.h" #include "data_entry.h" #include "ble_mailbox.h" #include "ieee_mailbox.h" /*---------------------------------------------------------------------------*/ #include #include #include /*---------------------------------------------------------------------------*/ #define BUSYWAIT_UNTIL(cond, max_time) \ do { \ rtimer_clock_t t0; \ t0 = RTIMER_NOW(); \ while(!(cond) && RTIMER_CLOCK_LT(RTIMER_NOW(), t0 + (max_time))); \ } while(0) /*---------------------------------------------------------------------------*/ #ifndef MIN #define MIN(n, m) (((n) < (m)) ? (n) : (m)) #endif /*---------------------------------------------------------------------------*/ #ifdef __GNUC__ #define CC_ALIGN_ATTR(n) __attribute__ ((aligned(n))) #else #define CC_ALIGN_ATTR(n) #endif /*---------------------------------------------------------------------------*/ #define DEBUG 0 #if DEBUG #define PRINTF(...) printf(__VA_ARGS__) #else #define PRINTF(...) #endif /*---------------------------------------------------------------------------*/ /* Data entry status field constants */ #define DATA_ENTRY_STATUS_PENDING 0x00 /* Not in use by the Radio CPU */ #define DATA_ENTRY_STATUS_ACTIVE 0x01 /* Open for r/w by the radio CPU */ #define DATA_ENTRY_STATUS_BUSY 0x02 /* Ongoing r/w */ #define DATA_ENTRY_STATUS_FINISHED 0x03 /* Free to use and to free */ #define DATA_ENTRY_STATUS_UNFINISHED 0x04 /* Partial RX entry */ /*---------------------------------------------------------------------------*/ /* RF stats data structure */ static uint8_t rf_stats[16] = { 0 }; /*---------------------------------------------------------------------------*/ /* RF Command status constants - Correspond to values in the CMDSTA register */ #define RF_CMD_STATUS_PENDING 0x00 #define RF_CMD_STATUS_DONE 0x01 #define RF_CMD_STATUS_ILLEGAL_PTR 0x81 #define RF_CMD_STATUS_UNKNOWN_CMD 0x82 #define RF_CMD_STATUS_UNKNOWN_DIR_CMD 0x83 #define RF_CMD_STATUS_CONTEXT_ERR 0x85 #define RF_CMD_STATUS_SCHEDULING_ERR 0x86 #define RF_CMD_STATUS_PAR_ERR 0x87 #define RF_CMD_STATUS_QUEUE_ERR 0x88 #define RF_CMD_STATUS_QUEUE_BUSY 0x89 /* Status values starting with 0x8 correspond to errors */ #define RF_CMD_STATUS_ERR_MASK 0x80 /* Return values for rf_send_cmd_ok */ #define RF_CMD_ERROR 0 #define RF_CMD_OK 1 /* The size of the RF commands buffer */ #define RF_CMD_BUFFER_SIZE 128 /*---------------------------------------------------------------------------*/ /* RF Radio Op status constants. Field 'status' in Radio Op command struct */ #define RF_RADIO_OP_STATUS_IDLE 0x0000 #define RF_RADIO_OP_STATUS_PENDING 0x0001 #define RF_RADIO_OP_STATUS_ACTIVE 0x0002 #define RF_RADIO_OP_STATUS_SKIPPED 0x0003 #define RF_RADIO_OP_STATUS_DONE_OK 0x0400 #define RF_RADIO_OP_STATUS_DONE_COUNTDOWN 0x0401 #define RF_RADIO_OP_STATUS_DONE_RXERR 0x0402 #define RF_RADIO_OP_STATUS_DONE_TIMEOUT 0x0403 #define RF_RADIO_OP_STATUS_DONE_STOPPED 0x0404 #define RF_RADIO_OP_STATUS_DONE_ABORT 0x0405 #define RF_RADIO_OP_STATUS_ERROR_PAST_START 0x0800 #define RF_RADIO_OP_STATUS_ERROR_START_TRIG 0x0801 #define RF_RADIO_OP_STATUS_ERROR_CONDITION 0x0802 #define RF_RADIO_OP_STATUS_ERROR_PAR 0x0803 #define RF_RADIO_OP_STATUS_ERROR_POINTER 0x0804 #define RF_RADIO_OP_STATUS_ERROR_CMDID 0x0805 #define RF_RADIO_OP_STATUS_ERROR_NO_SETUP 0x0807 #define RF_RADIO_OP_STATUS_ERROR_NO_FS 0x0808 #define RF_RADIO_OP_STATUS_ERROR_SYNTH_PROG 0x0809 /* Additional Op status values for IEEE mode */ #define RF_RADIO_OP_STATUS_IEEE_SUSPENDED 0x2001 #define RF_RADIO_OP_STATUS_IEEE_DONE_OK 0x2400 #define RF_RADIO_OP_STATUS_IEEE_DONE_BUSY 0x2401 #define RF_RADIO_OP_STATUS_IEEE_DONE_STOPPED 0x2402 #define RF_RADIO_OP_STATUS_IEEE_DONE_ACK 0x2403 #define RF_RADIO_OP_STATUS_IEEE_DONE_ACKPEND 0x2404 #define RF_RADIO_OP_STATUS_IEEE_DONE_TIMEOUT 0x2405 #define RF_RADIO_OP_STATUS_IEEE_DONE_BGEND 0x2406 #define RF_RADIO_OP_STATUS_IEEE_DONE_ABORT 0x2407 #define RF_RADIO_OP_STATUS_ERROR_WRONG_BG 0x0806 #define RF_RADIO_OP_STATUS_IEEE_ERROR_PAR 0x2800 #define RF_RADIO_OP_STATUS_IEEE_ERROR_NO_SETUP 0x2801 #define RF_RADIO_OP_STATUS_IEEE_ERROR_NO_FS 0x2802 #define RF_RADIO_OP_STATUS_IEEE_ERROR_SYNTH_PROG 0x2803 #define RF_RADIO_OP_STATUS_IEEE_ERROR_RXOVF 0x2804 #define RF_RADIO_OP_STATUS_IEEE_ERROR_TXUNF 0x2805 /* Op status values for BLE mode */ #define RF_RADIO_OP_STATUS_BLE_DONE_OK 0x1400 #define RF_RADIO_OP_STATUS_BLE_DONE_RXTIMEOUT 0x1401 #define RF_RADIO_OP_STATUS_BLE_DONE_NOSYNC 0x1402 #define RF_RADIO_OP_STATUS_BLE_DONE_RXERR 0x1403 #define RF_RADIO_OP_STATUS_BLE_DONE_CONNECT 0x1404 #define RF_RADIO_OP_STATUS_BLE_DONE_MAXNACK 0x1405 #define RF_RADIO_OP_STATUS_BLE_DONE_ENDED 0x1406 #define RF_RADIO_OP_STATUS_BLE_DONE_ABORT 0x1407 #define RF_RADIO_OP_STATUS_BLE_DONE_STOPPED 0x1408 #define RF_RADIO_OP_STATUS_BLE_ERROR_PAR 0x1800 #define RF_RADIO_OP_STATUS_BLE_ERROR_RXBUF 0x1801 #define RF_RADIO_OP_STATUS_BLE_ERROR_NO_SETUP 0x1802 #define RF_RADIO_OP_STATUS_BLE_ERROR_NO_FS 0x1803 #define RF_RADIO_OP_STATUS_BLE_ERROR_SYNTH_PROG 0x1804 #define RF_RADIO_OP_STATUS_BLE_ERROR_RXOVF 0x1805 #define RF_RADIO_OP_STATUS_BLE_ERROR_TXUNF 0x1806 /* Bits 15:12 signify the protocol */ #define RF_RADIO_OP_STATUS_PROTO_MASK 0xF000 #define RF_RADIO_OP_STATUS_PROTO_GENERIC 0x0000 #define RF_RADIO_OP_STATUS_PROTO_BLE 0x1000 #define RF_RADIO_OP_STATUS_PROTO_IEEE 0x2000 #define RF_RADIO_OP_STATUS_PROTO_PROP 0x3000 /* Bits 11:10 signify Running / Done OK / Done with error */ #define RF_RADIO_OP_MASKED_STATUS 0x0C00 #define RF_RADIO_OP_MASKED_STATUS_RUNNING 0x0000 #define RF_RADIO_OP_MASKED_STATUS_DONE 0x0400 #define RF_RADIO_OP_MASKED_STATUS_ERROR 0x0800 /*---------------------------------------------------------------------------*/ /** * \brief Returns the current status of a running Radio Op command * \param a A pointer with the buffer used to initiate the command * \return The value of the Radio Op buffer's status field * * This macro can be used to e.g. return the status of a previously * initiated background operation, or of an immediate command */ #define RF_RADIO_OP_GET_STATUS(a) GET_FIELD_V(a, radioOp, status) /*---------------------------------------------------------------------------*/ /* Special value returned by CMD_IEEE_CCA_REQ when an RSSI is not available */ #define RF_CMD_CCA_REQ_RSSI_UNKNOWN -128 /* Used for the return value of channel_clear */ #define RF_CCA_CLEAR 1 #define RF_CCA_BUSY 0 /* Used as an error return value for get_cca_info */ #define RF_GET_CCA_INFO_ERROR 0xFF /* * Values of the individual bits of the ccaInfo field in CMD_IEEE_CCA_REQ's * status struct */ #define RF_CMD_CCA_REQ_CCA_STATE_IDLE 0 /* 00 */ #define RF_CMD_CCA_REQ_CCA_STATE_BUSY 1 /* 01 */ #define RF_CMD_CCA_REQ_CCA_STATE_INVALID 2 /* 10 */ /*---------------------------------------------------------------------------*/ #define RF_MODE_BLE 0 #define RF_MODE_IEEE 1 /*---------------------------------------------------------------------------*/ /* How long to wait for an ongoing ACK TX to finish before starting frame TX */ #define TX_WAIT_TIMEOUT (RTIMER_SECOND >> 11) /* How long to wait for the RF to enter RX in rf_cmd_ieee_rx */ #define ENTER_RX_WAIT_TIMEOUT (RTIMER_SECOND >> 10) /*---------------------------------------------------------------------------*/ /* TX Power dBm lookup table - values from SmartRF Studio */ typedef struct output_config { radio_value_t dbm; uint8_t register_ib; uint8_t register_gc; } output_config_t; static const output_config_t output_power[] = { { 5, 0x29, 0x00 }, { 4, 0x20, 0x00 }, { 3, 0x19, 0x00 }, { 2, 0x25, 0x01 }, { 1, 0x21, 0x01 }, { 0, 0x1D, 0x01 }, { -3, 0x19, 0x03 }, { -6, 0x13, 0x03 }, { -9, 0x0F, 0x03 }, }; #define OUTPUT_CONFIG_COUNT (sizeof(output_power) / sizeof(output_config_t)) /* Max and Min Output Power in dBm */ #define OUTPUT_POWER_MIN (output_power[OUTPUT_CONFIG_COUNT - 1].dbm) #define OUTPUT_POWER_MAX (output_power[0].dbm) #define OUTPUT_POWER_UNKNOWN 0xFFFF /* Default TX Power - position in output_power[] */ #define CC26XX_RF_TX_POWER 0 const output_config_t *tx_power_current = &output_power[0]; /*---------------------------------------------------------------------------*/ #define RF_CORE_CLOCKS_MASK (RFC_PWR_PWMCLKEN_RFC_M | RFC_PWR_PWMCLKEN_CPE_M \ | RFC_PWR_PWMCLKEN_CPERAM_M) /*---------------------------------------------------------------------------*/ /* RF interrupts */ #define RX_IRQ IRQ_IEEE_RX_ENTRY_DONE #define TX_ACK_IRQ IRQ_IEEE_TX_ACK #define ERROR_IRQ IRQ_INTERNAL_ERROR /* Those IRQs are enabled all the time */ #define ENABLED_IRQS (RX_IRQ + ERROR_IRQ) /* * We only enable this right before starting frame TX, so we can sleep while * the TX is ongoing */ #define LAST_FG_CMD_DONE IRQ_LAST_FG_COMMAND_DONE #define cc26xx_rf_cpe0_isr RFCCPE0IntHandler #define cc26xx_rf_cpe1_isr RFCCPE1IntHandler /*---------------------------------------------------------------------------*/ /* * Buffers used to send commands to the RF core (generic and IEEE commands). * Some of those buffers are re-usable, some are not. * * If you are uncertain, declare a new buffer. */ /* * A buffer to send a CMD_IEEE_RX and to subsequently monitor its status * Do not use this buffer for any commands other than CMD_IEEE_RX */ static uint8_t cmd_ieee_rx_buf[RF_CMD_BUFFER_SIZE] CC_ALIGN_ATTR(4); /* * A buffer used to send immediate and foreground Radio Op (e.g. CMD_IEEE_TX) * commands. * * Do not re-use this buffer to send a command before the previous command * has been completed. * * Do not intermingle preparation of this buffer to send a command with calls * that might lead to a different command, since the latter will overwrite what * you have written in preparation for the former. */ static uint8_t cmd_immediate_buf[RF_CMD_BUFFER_SIZE] CC_ALIGN_ATTR(4); /*---------------------------------------------------------------------------*/ /* BLE macros, variables and buffers */ /* BLE Intervals: Send a burst of advertisements every BLE_ADV_INTERVAL secs */ #define BLE_ADV_INTERVAL (CLOCK_SECOND * 5) #define BLE_ADV_DUTY_CYCLE (CLOCK_SECOND / 10) #define BLE_ADV_MESSAGES 10 /* BLE Advertisement-related macros */ #define BLE_ADV_TYPE_DEVINFO 0x01 #define BLE_ADV_TYPE_NAME 0x09 #define BLE_ADV_TYPE_MANUFACTURER 0xFF #define BLE_ADV_NAME_BUF_LEN 32 #define BLE_ADV_PAYLOAD_BUF_LEN 64 #define BLE_UUID_SIZE 16 #if CC26XX_RF_BLE_SUPPORT /* BLE buffers / variables */ static unsigned char ble_cmd_buf[32] CC_ALIGN_ATTR(4) = { 0 }; static unsigned char ble_tx_rx_buf[128] CC_ALIGN_ATTR(4); static uint8_t ble_mode_on; /* BLE beacond config */ static struct ble_beacond_config { clock_time_t interval; char adv_name[BLE_ADV_NAME_BUF_LEN]; } beacond_config; /* BLE overrides */ static uint32_t ble_overrides[] = { 0x00364038, /* Synth: Set RTRIM (POTAILRESTRIM) to 6 */ 0x000784A3, /* Synth: Set FREF = 3.43 MHz (24 MHz / 7) */ 0xA47E0583, /* Synth: Set loop bandwidth after lock to 80 kHz (K2) */ 0xEAE00603, /* Synth: Set loop bandwidth after lock to 80 kHz (K3, LSB) */ 0x00010623, /* Synth: Set loop bandwidth after lock to 80 kHz (K3, MSB) */ 0x00456088, /* Adjust AGC reference level */ 0xFFFFFFFF, /* End of override list */ }; PROCESS(cc26xx_rf_ble_beacon_process, "CC26xx RF BLE Beacon Process"); static void init_ble(void); #else #define init_ble(...) #endif /* CC26XX_RF_BLE_SUPPORT */ /*---------------------------------------------------------------------------*/ #define RX_BUF_SIZE 140 /* Four receive buffers entries with room for 1 IEEE802.15.4 frame in each */ static uint8_t rx_buf_0[RX_BUF_SIZE] CC_ALIGN_ATTR(4); static uint8_t rx_buf_1[RX_BUF_SIZE] CC_ALIGN_ATTR(4); static uint8_t rx_buf_2[RX_BUF_SIZE] CC_ALIGN_ATTR(4); static uint8_t rx_buf_3[RX_BUF_SIZE] CC_ALIGN_ATTR(4); /* The RX Data Queue */ static dataQueue_t rx_data_queue = { 0 }; /* Receive entry pointer to keep track of read items */ volatile static uint8_t *rx_read_entry; /*---------------------------------------------------------------------------*/ /* The outgoing frame buffer */ #define TX_BUF_SIZE 180 static uint8_t tx_buf[TX_BUF_SIZE]; /*---------------------------------------------------------------------------*/ /* Overrides for IEEE 802.15.4, differential mode */ static uint32_t ieee_overrides[] = { 0x00354038, /* Synth: Set RTRIM (POTAILRESTRIM) to 5 */ 0x4001402D, /* Synth: Correct CKVD latency setting (address) */ 0x00608402, /* Synth: Correct CKVD latency setting (value) */ 0x4001405D, /* Synth: Set ANADIV DIV_BIAS_MODE to PG1 (address) */ 0x1801F800, /* Synth: Set ANADIV DIV_BIAS_MODE to PG1 (value) */ 0x000784A3, /* Synth: Set FREF = 3.43 MHz (24 MHz / 7) */ 0xA47E0583, /* Synth: Set loop bandwidth after lock to 80 kHz (K2) */ 0xEAE00603, /* Synth: Set loop bandwidth after lock to 80 kHz (K3, LSB) */ 0x00010623, /* Synth: Set loop bandwidth after lock to 80 kHz (K3, MSB) */ 0x002B50DC, /* Adjust AGC DC filter */ 0x05000243, /* Increase synth programming timeout */ 0x002082C3, /* Increase synth programming timeout */ 0xFFFFFFFF, /* End of override list */ }; /*---------------------------------------------------------------------------*/ PROCESS(cc26xx_rf_process, "CC26xx RF driver"); /*---------------------------------------------------------------------------*/ static int on(void); static int off(void); static void setup_interrupts(void); /*---------------------------------------------------------------------------*/ static uint8_t rf_is_accessible(void) { if(ti_lib_prcm_rf_ready() && ti_lib_prcm_power_domain_status(PRCM_DOMAIN_RFCORE) == PRCM_DOMAIN_POWER_ON) { return 1; } return 0; } /*---------------------------------------------------------------------------*/ /** * \brief Sends a command to the RF core. * * \param cmd The command value or a pointer to a command buffer * \param status A pointer to a variable which will hold the status * \return RF_CMD_OK or RF_CMD_ERROR * * This function supports all three types of command (Radio OP, immediate and * direct) * * For immediate and Radio OPs, cmd is a pointer to the data structure * containing the command and its parameters. This data structure must be * 4-byte aligned. * * For direct commands, cmd contains the value of the command alongside its * parameters * * The caller is responsible of allocating and populating cmd for Radio OP and * immediate commands * * The caller is responsible for allocating status */ static uint_fast8_t rf_send_cmd(uint32_t cmd, uint32_t *status) { uint32_t timeout_count = 0; /* * Make sure ContikiMAC doesn't turn us off from within an interrupt while * we are accessing RF Core registers */ ti_lib_int_master_disable(); if(!rf_is_accessible()) { PRINTF("rf_send_cmd: RF was off\n"); ti_lib_int_master_enable(); return RF_CMD_ERROR; } HWREG(RFC_DBELL_BASE + RFC_DBELL_O_CMDR) = cmd; do { *status = HWREG(RFC_DBELL_BASE + RFC_DBELL_O_CMDSTA); if(++timeout_count > 50000) { PRINTF("rf_send_cmd: Timeout\n"); ti_lib_int_master_enable(); return RF_CMD_ERROR; } } while(*status == RF_CMD_STATUS_PENDING); ti_lib_int_master_enable(); /* * If we reach here the command is no longer pending. It is either completed * successfully or with error */ return *status == RF_CMD_STATUS_DONE; } /*---------------------------------------------------------------------------*/ /** * \brief Checks whether the RFC domain is accessible and the RFC is in IEEE RX * \return 1: RFC in RX mode (and therefore accessible too). 0 otherwise */ static uint8_t rf_is_on(void) { if(!rf_is_accessible()) { return 0; } return RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf) == RF_RADIO_OP_STATUS_ACTIVE; } /*---------------------------------------------------------------------------*/ /** * \brief Check the RF's TX status * \return 1 RF is transmitting * \return 0 RF is not transmitting * * TX mode may be triggered either by a CMD_IEEE_TX or by the automatic * transmission of an ACK frame. */ static uint8_t transmitting(void) { uint32_t cmd_status; /* If we are off, we are not in TX */ if(!rf_is_accessible()) { return 0; } memset(cmd_immediate_buf, 0x00, SIZEOF_STRUCT(CMD_IEEE_CCA_REQ)); GET_FIELD(cmd_immediate_buf, command, commandNo) = CMD_IEEE_CCA_REQ; if(rf_send_cmd((uint32_t)cmd_immediate_buf, &cmd_status) == RF_CMD_ERROR) { PRINTF("transmitting: CMDSTA=0x%08lx, status=0x%04x\n", cmd_status, RF_RADIO_OP_GET_STATUS(cmd_immediate_buf)); return 0; } if((GET_FIELD(cmd_immediate_buf, CMD_IEEE_CCA_REQ, currentRssi) == RF_CMD_CCA_REQ_RSSI_UNKNOWN) && (GET_BITFIELD(cmd_immediate_buf, CMD_IEEE_CCA_REQ, ccaInfo, ccaEnergy) == RF_CMD_CCA_REQ_CCA_STATE_BUSY)) { return 1; } return 0; } /*---------------------------------------------------------------------------*/ /** * \brief Returns CCA information * \return RF_GET_CCA_INFO_ERROR if the RF was not on * \return On success, the return value is formatted as per the ccaInfo field * of CMD_IEEE_CCA_REQ * * It is the caller's responsibility to make sure the RF is on. This function * will return RF_GET_CCA_INFO_ERROR if the RF is off * * This function will in fact wait for a valid RSSI signal */ static uint8_t get_cca_info(void) { uint32_t cmd_status; int8_t rssi; if(!rf_is_on()) { PRINTF("get_cca_info: Not on\n"); return RF_GET_CCA_INFO_ERROR; } rssi = RF_CMD_CCA_REQ_RSSI_UNKNOWN; while(rssi == RF_CMD_CCA_REQ_RSSI_UNKNOWN || rssi == 0) { memset(cmd_immediate_buf, 0x00, SIZEOF_STRUCT(CMD_IEEE_CCA_REQ)); GET_FIELD(cmd_immediate_buf, command, commandNo) = CMD_IEEE_CCA_REQ; if(rf_send_cmd((uint32_t)cmd_immediate_buf, &cmd_status) == RF_CMD_ERROR) { PRINTF("get_cca_info: CMDSTA=0x%08lx, status=0x%04x\n", cmd_status, RF_RADIO_OP_GET_STATUS(cmd_immediate_buf)); return RF_GET_CCA_INFO_ERROR; } rssi = GET_FIELD(cmd_immediate_buf, CMD_IEEE_CCA_REQ, currentRssi); } /* We have a valid RSSI signal. Return the CCA Info */ return GET_FIELD(cmd_immediate_buf, CMD_IEEE_CCA_REQ, ccaInfo); } /*---------------------------------------------------------------------------*/ /** * \brief Reads the current signal strength (RSSI) * \return The current RSSI in dBm or CMD_GET_RSSI_UNKNOWN * * This function reads the current RSSI on the currently configured * channel. */ static radio_value_t get_rssi(void) { uint32_t cmd_status; int8_t rssi; uint8_t was_off = 0; /* If we are off, turn on first */ if(!rf_is_on()) { was_off = 1; if(on() != RF_CMD_OK) { PRINTF("get_rssi: on() failed\n"); return RF_CMD_CCA_REQ_RSSI_UNKNOWN; } } memset(cmd_immediate_buf, 0x00, SIZEOF_STRUCT(CMD_GET_RSSI)); GET_FIELD(cmd_immediate_buf, command, commandNo) = CMD_GET_RSSI; if(rf_send_cmd((uint32_t)cmd_immediate_buf, &cmd_status) == RF_CMD_ERROR) { rssi = RF_CMD_CCA_REQ_RSSI_UNKNOWN; } /* Current RSSI in bits 23:16 of cmd_status */ rssi = (cmd_status >> 16) & 0xFF; /* If we were off, turn back off */ if(was_off) { off(); } return rssi; } /*---------------------------------------------------------------------------*/ /* Returns the current TX power in dBm */ static radio_value_t get_tx_power(void) { return tx_power_current->dbm; } /*---------------------------------------------------------------------------*/ /* * Set TX power to 'at least' power dBm * This works with a lookup table. If the value of 'power' does not exist in * the lookup table, TXPOWER will be set to the immediately higher available * value */ static void set_tx_power(radio_value_t power) { uint32_t cmd_status; int i; /* Send a CMD_SET_TX_POWER command to the RF */ memset(cmd_immediate_buf, 0x00, SIZEOF_STRUCT(CMD_SET_TX_POWER)); GET_FIELD(cmd_immediate_buf, command, commandNo) = CMD_SET_TX_POWER; for(i = OUTPUT_CONFIG_COUNT - 1; i >= 0; --i) { if(power <= output_power[i].dbm) { GET_FIELD(cmd_immediate_buf, CMD_SET_TX_POWER, txPower) = BITVALUE(CMD_SET_TX_POWER, txPower, IB, output_power[i].register_ib) | BITVALUE(CMD_SET_TX_POWER, txPower, GC, output_power[i].register_gc) | BITVALUE(CMD_SET_TX_POWER, txPower, tempCoeff, 0); if(rf_send_cmd((uint32_t)cmd_immediate_buf, &cmd_status) == RF_CMD_OK) { /* Success: Remember the new setting */ tx_power_current = &output_power[i]; } else { PRINTF("set_tx_power: CMDSTA=0x%08lx\n", cmd_status); } return; } } } /*---------------------------------------------------------------------------*/ /** * \brief Wait till running radio Op command completes * * \return RF_CMD_ERROR or RF_CMD_OK * * RF_CMD_OK will be returned if the Radio Op returned with * RF_RADIO_OP_STATUS_DONE_OK * * RF_CMD_ERROR will be returned in the radio op returned with any other * RF_RADIO_OP_STATUS_DONE_xyz */ static uint_fast8_t rf_wait_cmd_completed_ok(uint8_t *cmd) { _TYPE_radioOp_status tmp_status; uint32_t timeoutCount = 0; /* * 0x04XX=DONE, 0x0400=DONE_OK while all other "DONE" values means done * but with some kind of error (ref. "Common radio operation status codes") */ do { tmp_status = GET_FIELD_V(cmd, radioOp, status); if(++timeoutCount > 500000) { return RF_CMD_ERROR; } } while((tmp_status & RF_RADIO_OP_MASKED_STATUS) != RF_RADIO_OP_MASKED_STATUS_DONE); return tmp_status == RF_RADIO_OP_STATUS_DONE_OK; } /*---------------------------------------------------------------------------*/ /** * \brief Builds common radio parameters for radio operations * * \param *cmd Pointer to buffer to add parameters to * \param command Radio command number (e.g. COMMAND_RADIO_SETUP) * * \note The buffer must be emptied with memset() before calling this function * * \return None */ static void rf_build_radio_op_cmd(uint8_t *cmd, uint16_t command) { GET_FIELD(cmd, radioOp, commandNo) = command; GET_FIELD(cmd, radioOp, status) = IDLE; GET_FIELD(cmd, radioOp, pNextOp) = NULL; GET_FIELD(cmd, radioOp, startTime) = 0; GET_FIELD(cmd, radioOp, startTrigger) = TRIG_NOW; GET_FIELD(cmd, radioOp, condition) = COND_NEVER; } /*---------------------------------------------------------------------------*/ /** * \brief Sends a CMD_RADIO_SETUP for the selected mode (IEEE or BLE) * \param mode RF_MODE_BLE or RF_MODE_IEEE * \return RF_CMD_OK or RF_CMD_ERROR * * ToDo: Likely to need one more argument to set bNoAdi on first startup * vs when coming back from sleep */ static uint8_t rf_radio_setup(uint8_t mode) { uint32_t cmd_status; /* Create radio setup command */ memset(cmd_immediate_buf, 0x00, SIZEOF_RADIO_OP(CMD_RADIO_SETUP)); rf_build_radio_op_cmd(cmd_immediate_buf, CMD_RADIO_SETUP); /* Set output power to the current (or default) value */ GET_FIELD(cmd_immediate_buf, CMD_RADIO_SETUP, txPower) = BITVALUE(CMD_RADIO_SETUP, txPower, IB, tx_power_current->register_ib) | BITVALUE(CMD_RADIO_SETUP, txPower, GC, tx_power_current->register_gc) | BITVALUE(CMD_RADIO_SETUP, txPower, tempCoeff, 0); /* Do mode-dependent things (e.g. apply overrides) */ if(mode == RF_MODE_IEEE) { /* Add override control pointer */ GET_FIELD(cmd_immediate_buf, CMD_RADIO_SETUP, pRegOverride) = ieee_overrides; #if CC26XX_RF_BLE_SUPPORT } else if(mode == RF_MODE_BLE) { /* Add override control pointer */ GET_FIELD(cmd_immediate_buf, CMD_RADIO_SETUP, pRegOverride) = ble_overrides; #endif } else { PRINTF("rf_radio_setup: Unknown mode %u\n", mode); return RF_CMD_ERROR; } /* Lastly, set the mode */ GET_FIELD(cmd_immediate_buf, CMD_RADIO_SETUP, mode) = mode; /* Send Radio setup to RF Core */ if(rf_send_cmd((uint32_t)cmd_immediate_buf, &cmd_status) != RF_CMD_OK) { PRINTF("rf_radio_setup: CMD_RADIO_SETUP, CMDSTA=0x%08lx, status=0x%04x\n", cmd_status, RF_RADIO_OP_GET_STATUS(cmd_immediate_buf)); return RF_CMD_ERROR; } /* Wait until radio setup is done */ if(rf_wait_cmd_completed_ok(cmd_immediate_buf) != RF_CMD_OK) { PRINTF("rf_radio_setup: CMD_RADIO_SETUP wait, CMDSTA=0x%08lx, status=0x%04x\n", cmd_status, RF_RADIO_OP_GET_STATUS(cmd_immediate_buf)); return RF_CMD_ERROR; } return RF_CMD_OK; } /*---------------------------------------------------------------------------*/ /** * \brief Applies patches (if any) * \return RF_CMD_OK or RF_CMD_ERROR * * Currently patches are not required. */ static uint8_t apply_patches() { uint32_t cmd_status; /* Patch of uninitialized pointer */ *((uint32_t *)0x21000028) = 0x00000000; /* Start radio timer (RAT) */ if(rf_send_cmd(CMDR_DIR_CMD(CMD_START_RAT), &cmd_status) != RF_CMD_OK) { PRINTF("apply_patches: START_RAT fail, CMDSTA=0x%08lx\n", cmd_status); return RF_CMD_ERROR; } return RF_CMD_OK; } /*---------------------------------------------------------------------------*/ /** * \brief Set up radio in IEEE802.15.4 RX mode * * \return RF_CMD_OK Succeeded * \return RF_CMD_ERROR Failed * * This function assumes that cmd_ieee_rx_buf has been previously populated * with correct values. This can be done through init_rf_params (sets defaults) * or through Contiki's extended RF API (set_value, set_object) */ static uint8_t rf_cmd_ieee_rx() { uint32_t cmd_status; rtimer_clock_t t0; int ret; ret = rf_send_cmd((uint32_t)cmd_ieee_rx_buf, &cmd_status); if(ret != RF_CMD_OK) { PRINTF("rf_cmd_ieee_rx: ret=%d, CMDSTA=0x%08lx, status=0x%04x\n", ret, cmd_status, RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf)); } t0 = RTIMER_NOW(); while(RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf) != RF_RADIO_OP_STATUS_ACTIVE && (RTIMER_CLOCK_LT(RTIMER_NOW(), t0 + ENTER_RX_WAIT_TIMEOUT))); /* Wait to enter RX */ if(RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf) != RF_RADIO_OP_STATUS_ACTIVE) { PRINTF("rf_cmd_ieee_rx: CMDSTA=0x%08lx, status=0x%04x\n", cmd_status, RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf)); return RF_CMD_ERROR; } return ret; } /*---------------------------------------------------------------------------*/ static void init_rx_buffers(void) { /* Two-element circular buffer, hardcoded for now.. */ GET_FIELD(rx_buf_0, dataEntry, pNextEntry) = rx_buf_1; GET_FIELD(rx_buf_0, dataEntry, config) = 0x04; GET_FIELD(rx_buf_0, dataEntry, length) = sizeof(rx_buf_0) - 8; GET_FIELD(rx_buf_1, dataEntry, pNextEntry) = rx_buf_2; GET_FIELD(rx_buf_1, dataEntry, config) = 0x04; GET_FIELD(rx_buf_1, dataEntry, length) = sizeof(rx_buf_1) - 8; GET_FIELD(rx_buf_2, dataEntry, pNextEntry) = rx_buf_3; GET_FIELD(rx_buf_2, dataEntry, config) = 0x04; GET_FIELD(rx_buf_2, dataEntry, length) = sizeof(rx_buf_2) - 8; /* Point to first element again */ GET_FIELD(rx_buf_3, dataEntry, pNextEntry) = rx_buf_0; GET_FIELD(rx_buf_3, dataEntry, config) = 0x04; GET_FIELD(rx_buf_3, dataEntry, length) = sizeof(rx_buf_3) - 8; } /*---------------------------------------------------------------------------*/ static void init_rf_params(void) { memset(cmd_ieee_rx_buf, 0x00, SIZEOF_RADIO_OP(CMD_IEEE_RX)); GET_FIELD(cmd_ieee_rx_buf, radioOp, commandNo) = CMD_IEEE_RX; GET_FIELD(cmd_ieee_rx_buf, radioOp, status) = IDLE; GET_FIELD(cmd_ieee_rx_buf, radioOp, pNextOp) = NULL; GET_FIELD(cmd_ieee_rx_buf, radioOp, startTime) = 0x00000000; GET_FIELD(cmd_ieee_rx_buf, radioOp, startTrigger) = TRIG_NOW; GET_FIELD(cmd_ieee_rx_buf, radioOp, condition) = COND_NEVER; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, channel) = CC26XX_RF_CHANNEL; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, rxConfig) = BITVALUE(CMD_IEEE_RX, rxConfig, bAutoFlushCrc, 0) | BITVALUE(CMD_IEEE_RX, rxConfig, bAutoFlushIgn, 0) | BITVALUE(CMD_IEEE_RX, rxConfig, bIncludePhyHdr, 0) | BITVALUE(CMD_IEEE_RX, rxConfig, bIncludeCrc, 1) | BITVALUE(CMD_IEEE_RX, rxConfig, bAppendRssi, 1) | BITVALUE(CMD_IEEE_RX, rxConfig, bAppendCorrCrc, 1) | BITVALUE(CMD_IEEE_RX, rxConfig, bAppendSrcInd, 0) | BITVALUE(CMD_IEEE_RX, rxConfig, bAppendTimestamp, 0); GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, pRxQ) = &rx_data_queue; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, pOutput) = rf_stats; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, frameFiltOpt) = #if CC26XX_RF_CONF_PROMISCOUS BITVALUE(CMD_IEEE_RX, frameFiltOpt, frameFiltEn, 0) | #else BITVALUE(CMD_IEEE_RX, frameFiltOpt, frameFiltEn, 1) | #endif BITVALUE(CMD_IEEE_RX, frameFiltOpt, frameFiltStop, 1) | #if CC26XX_RF_CONF_AUTOACK BITVALUE(CMD_IEEE_RX, frameFiltOpt, autoAckEn, 1) | #else BITVALUE(CMD_IEEE_RX, frameFiltOpt, autoAckEn, 0) | #endif BITVALUE(CMD_IEEE_RX, frameFiltOpt, slottedAckEn, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, autoPendEn, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, defaultPend, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, bPendDataReqOnly, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, bPanCoord, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, maxFrameVersion, 1) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, bStrictLenFilter, 0); /* Receive all frame types */ GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, frameTypes) = BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt0Beacon, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt1Data, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt2Ack, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt3MacCmd, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt4Reserved, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt5Reserved, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt6Reserved, 1) | BITVALUE(CMD_IEEE_RX, frameTypes, bAcceptFt7Reserved, 1); /* Configure CCA settings */ GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, ccaOpt) = BITVALUE(CMD_IEEE_RX, ccaOpt, ccaEnEnergy, 1) | BITVALUE(CMD_IEEE_RX, ccaOpt, ccaEnCorr, 0) | BITVALUE(CMD_IEEE_RX, ccaOpt, ccaEnSync, 0) | BITVALUE(CMD_IEEE_RX, ccaOpt, ccaCorrOp, 0) | BITVALUE(CMD_IEEE_RX, ccaOpt, ccaSyncOp, 0); /* Set CCA RSSI Threshold, 0xA6 corresponds to -90dBm (two's comp.)*/ GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, ccaRssiThr) = 0xA6; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, numExtEntries) = 0x00; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, numShortEntries) = 0x00; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, pExtEntryList) = 0; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, pShortEntryList) = 0; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, endTrigger) = TRIG_NEVER; GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, endTime) = 0x00000000; } /*---------------------------------------------------------------------------*/ /** * \brief Turn on power to the RFC and boot it. * * \return RF_CMD_OK or RF_CMD_ERROR */ static int power_up(void) { uint32_t cmd_status; ti_lib_int_master_disable(); ti_lib_int_pend_clear(INT_RF_CPE0); ti_lib_int_pend_clear(INT_RF_CPE1); ti_lib_int_disable(INT_RF_CPE0); ti_lib_int_disable(INT_RF_CPE1); /* Enable RF Core power domain */ ti_lib_prcm_power_domain_on(PRCM_DOMAIN_RFCORE); while(ti_lib_prcm_power_domain_status(PRCM_DOMAIN_RFCORE) != PRCM_DOMAIN_POWER_ON); ti_lib_prcm_domain_enable(PRCM_DOMAIN_RFCORE); ti_lib_prcm_load_set(); while(!ti_lib_prcm_load_get()); while(!rf_is_accessible()) { PRINTF("power_up: Not ready\n"); } HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIFG) = 0x0; HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIEN) = 0x0; ti_lib_int_enable(INT_RF_CPE0); ti_lib_int_enable(INT_RF_CPE1); ti_lib_int_master_enable(); /* Let CPE boot */ HWREG(RFC_PWR_NONBUF_BASE + RFC_PWR_O_PWMCLKEN) = RF_CORE_CLOCKS_MASK; /* Send ping (to verify RFCore is ready and alive) */ if(rf_send_cmd(CMDR_DIR_CMD(CMD_PING), &cmd_status) != RF_CMD_OK) { PRINTF("power_up: CMD_PING fail, CMDSTA=0x%08lx\n", cmd_status); return RF_CMD_ERROR; } return RF_CMD_OK; } /*---------------------------------------------------------------------------*/ /** * \brief Disable RFCORE clock domain in the MCU VD and turn off the RFCORE PD */ static void power_down(void) { ti_lib_int_master_disable(); ti_lib_int_disable(INT_RF_CPE0); ti_lib_int_disable(INT_RF_CPE1); if(rf_is_accessible()) { HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIFG) = 0x0; HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIEN) = 0x0; } /* Shut down the RFCORE clock domain in the MCU VD */ ti_lib_prcm_domain_disable(PRCM_DOMAIN_RFCORE); ti_lib_prcm_load_set(); while(!ti_lib_prcm_load_get()); /* Turn off RFCORE PD */ ti_lib_prcm_power_domain_off(PRCM_DOMAIN_RFCORE); while(ti_lib_prcm_power_domain_status(PRCM_DOMAIN_RFCORE) != PRCM_DOMAIN_POWER_OFF); ti_lib_int_pend_clear(INT_RF_CPE0); ti_lib_int_pend_clear(INT_RF_CPE1); ti_lib_int_enable(INT_RF_CPE0); ti_lib_int_enable(INT_RF_CPE1); ti_lib_int_master_enable(); } /*---------------------------------------------------------------------------*/ static int rx_on(void) { int ret; /* Get status of running IEEE_RX (if any) */ if(rf_is_on()) { PRINTF("rx_on: We were on. PD=%u, RX=0x%04x \n", rf_is_accessible(), RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf)); return RF_CMD_OK; } /* Put CPE in RX using the currently configured parameters */ ret = rf_cmd_ieee_rx(); if(ret) { ENERGEST_ON(ENERGEST_TYPE_LISTEN); } return ret; } /*---------------------------------------------------------------------------*/ static int rx_off(void) { uint32_t cmd_status; int ret; /* If we are off, do nothing */ if(!rf_is_on()) { return RF_CMD_OK; } /* Wait for ongoing ACK TX to finish */ while(transmitting()); /* Send a CMD_STOP command to RF Core */ if(rf_send_cmd(CMDR_DIR_CMD(CMD_ABORT), &cmd_status) != RF_CMD_OK) { PRINTF("RX off: CMD_ABORT status=0x%08lx\n", cmd_status); /* Continue nonetheless */ } while(rf_is_on()); if(RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf) == IEEE_DONE_STOPPED || RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf) == IEEE_DONE_ABORT) { /* Stopped gracefully */ ENERGEST_OFF(ENERGEST_TYPE_LISTEN); ret = RF_CMD_OK; } else { PRINTF("RX off: BG status=0x%04x\n", RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf)); ret = RF_CMD_ERROR; } return ret; } /*---------------------------------------------------------------------------*/ static void rx_isr(void) { process_poll(&cc26xx_rf_process); } /*---------------------------------------------------------------------------*/ void cc26xx_rf_cpe1_isr(void) { ENERGEST_ON(ENERGEST_TYPE_IRQ); ti_lib_int_master_disable(); PRINTF("RF Error\n"); if(!rf_is_accessible()) { if(power_up() != RF_CMD_OK) { return; } } /* Clear interrupt flags */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIFG) = 0x0; ti_lib_int_master_enable(); ENERGEST_OFF(ENERGEST_TYPE_IRQ); } /*---------------------------------------------------------------------------*/ void cc26xx_rf_cpe0_isr(void) { ENERGEST_ON(ENERGEST_TYPE_IRQ); if(!rf_is_accessible()) { printf("RF ISR called but RF not ready... PANIC!!\n"); if(power_up() != RF_CMD_OK) { PRINTF("power_up() failed\n"); return; } } ti_lib_int_master_disable(); if(HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIFG) & RX_IRQ) { rx_isr(); } /* Clear interrupt flags */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIFG) = 0x0; ti_lib_int_master_enable(); ENERGEST_OFF(ENERGEST_TYPE_IRQ); } /*---------------------------------------------------------------------------*/ static void setup_interrupts(void) { /* We are already turned on by the caller, so this should not happen */ if(!rf_is_accessible()) { PRINTF("setup_interrupts: No access\n"); return; } /* Disable interrupts */ ti_lib_int_master_disable(); /* Set all interrupt channels to CPE0 channel, error to CPE1 */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEISL) = ERROR_IRQ; /* Acknowledge TX_Frame, Rx_Entry_Done and ERROR */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIEN) = ENABLED_IRQS; /* Clear interrupt flags, active low clear(?) */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIFG) = 0x0; ti_lib_int_pend_clear(INT_RF_CPE0); ti_lib_int_pend_clear(INT_RF_CPE1); ti_lib_int_enable(INT_RF_CPE0); ti_lib_int_enable(INT_RF_CPE1); ti_lib_int_master_enable(); } /*---------------------------------------------------------------------------*/ static uint8_t request(void) { /* * We rely on the RDC layer to turn us on and off. Thus, if we are on we * will only allow sleep, standby otherwise */ if(rf_is_on()) { return LPM_MODE_SLEEP; } return LPM_MODE_MAX_SUPPORTED; } /*---------------------------------------------------------------------------*/ LPM_MODULE(cc26xx_rf_lpm_module, request, NULL, NULL); /*---------------------------------------------------------------------------*/ static int init(void) { lpm_register_module(&cc26xx_rf_lpm_module); /* Enable IEEE, BLE and Common-CMD APIs */ HWREG(PRCM_BASE + PRCM_O_RFCMODESEL) = PRCM_RFCMODESEL_CURR_MODE5; /* Wipe out the BLE adv buffer */ init_ble(); /* Initialise RX buffers */ memset(rx_buf_0, 0, RX_BUF_SIZE); memset(rx_buf_1, 0, RX_BUF_SIZE); memset(rx_buf_2, 0, RX_BUF_SIZE); memset(rx_buf_3, 0, RX_BUF_SIZE); /* Set of RF Core data queue. Circular buffer, no last entry */ rx_data_queue.pCurrEntry = rx_buf_0; rx_data_queue.pLastEntry = NULL; /* Initialize current read pointer to first element (used in ISR) */ rx_read_entry = rx_buf_0; /* Populate the RF parameters data structure with default values */ init_rf_params(); if(on() != RF_CMD_OK) { PRINTF("init: on() failed\n"); return RF_CMD_ERROR; } ENERGEST_ON(ENERGEST_TYPE_LISTEN); process_start(&cc26xx_rf_process, NULL); return 1; } /*---------------------------------------------------------------------------*/ static int prepare(const void *payload, unsigned short payload_len) { int len = MIN(payload_len, sizeof(tx_buf)); memcpy(tx_buf, payload, len); return RF_CMD_OK; } /*---------------------------------------------------------------------------*/ static int transmit(unsigned short transmit_len) { int ret; uint8_t was_off = 0; uint32_t cmd_status; uint16_t stat; uint8_t tx_active = 0; rtimer_clock_t t0; if(!rf_is_on()) { was_off = 1; if(on() != RF_CMD_OK) { PRINTF("transmit: on() failed\n"); return RF_CMD_ERROR; } } /* * We are certainly not TXing a frame as a result of CMD_IEEE_TX, but we may * be in the process of TXing an ACK. In that case, wait for the TX to finish * or return after approx TX_WAIT_TIMEOUT */ t0 = RTIMER_NOW(); do { tx_active = transmitting(); } while(tx_active == 1 && (RTIMER_CLOCK_LT(RTIMER_NOW(), t0 + TX_WAIT_TIMEOUT))); if(tx_active) { PRINTF("transmit: Already TXing and wait timed out\n"); if(was_off) { off(); } return RADIO_TX_COLLISION; } /* Send the CMD_IEEE_TX command */ memset(cmd_immediate_buf, 0, SIZEOF_RADIO_OP(CMD_IEEE_TX)); rf_build_radio_op_cmd(cmd_immediate_buf, CMD_IEEE_TX); GET_FIELD(cmd_immediate_buf, CMD_IEEE_TX, payloadLen) = transmit_len; GET_FIELD(cmd_immediate_buf, CMD_IEEE_TX, pPayload) = tx_buf; /* Enable the LAST_FG_COMMAND_DONE interrupt, which will wake us up */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIEN) = ENABLED_IRQS + LAST_FG_CMD_DONE; ret = rf_send_cmd((uint32_t)cmd_immediate_buf, &cmd_status); if(ret) { /* If we enter here, TX actually started */ ENERGEST_OFF(ENERGEST_TYPE_LISTEN); ENERGEST_ON(ENERGEST_TYPE_TRANSMIT); /* Idle away while the command is running */ while((RF_RADIO_OP_GET_STATUS(cmd_immediate_buf) & RF_RADIO_OP_MASKED_STATUS) == RF_RADIO_OP_MASKED_STATUS_RUNNING) { lpm_sleep(); } stat = RF_RADIO_OP_GET_STATUS(cmd_immediate_buf); if(stat == RF_RADIO_OP_STATUS_IEEE_DONE_OK) { /* Sent OK */ RIMESTATS_ADD(lltx); ret = RADIO_TX_OK; } else { /* Operation completed, but frame was not sent */ PRINTF("transmit: ret=%d, CMDSTA=0x%08lx, status=0x%04x\n", ret, cmd_status, stat); ret = RADIO_TX_ERR; } } else { /* Failure sending the CMD_IEEE_TX command */ PRINTF("transmit: ret=%d, CMDSTA=0x%08lx, status=0x%04x\n", ret, cmd_status, RF_RADIO_OP_GET_STATUS(cmd_immediate_buf)); ret = RADIO_TX_ERR; } /* * Update ENERGEST state here, before a potential call to off(), which * will correctly update it if required. */ ENERGEST_OFF(ENERGEST_TYPE_TRANSMIT); ENERGEST_ON(ENERGEST_TYPE_LISTEN); /* * Disable LAST_FG_COMMAND_DONE interrupt. We don't really care about it * except when we are transmitting */ HWREG(RFC_DBELL_NONBUF_BASE + RFC_DBELL_O_RFCPEIEN) = ENABLED_IRQS; return ret; } /*---------------------------------------------------------------------------*/ static int send(const void *payload, unsigned short payload_len) { prepare(payload, payload_len); return transmit(payload_len); } /*---------------------------------------------------------------------------*/ static int read_frame(void *buf, unsigned short buf_len) { int len = 0; if(GET_FIELD_V(rx_read_entry, dataEntry, status) == DATA_ENTRY_STATUS_FINISHED) { /* Set status to 0 "Pending" in element */ GET_FIELD_V(rx_read_entry, dataEntry, status) = DATA_ENTRY_STATUS_PENDING; if(rx_read_entry[8] > 0) { memcpy(buf, (char *)&rx_read_entry[9], buf_len); /* Remove the footer */ len = MIN(buf_len, rx_read_entry[8] - 4); int rssi = (int8_t)rx_read_entry[9 + len + 2]; packetbuf_set_attr(PACKETBUF_ATTR_RSSI, rssi); RIMESTATS_ADD(llrx); /* Clear the length byte */ rx_read_entry[8] = 0; } /* Move read entry pointer to next entry */ rx_read_entry = GET_FIELD_V(rx_read_entry, dataEntry, pNextEntry); } return len; } /*---------------------------------------------------------------------------*/ static int channel_clear(void) { uint8_t was_off = 0; uint8_t cca_info; int ret = RF_CCA_CLEAR; /* * If we are in the middle of a BLE operation, we got called by ContikiMAC * from within an interrupt context. Indicate a clear channel */ #if CC26XX_RF_BLE_SUPPORT if(ble_mode_on) { PRINTF("channel_clear: Interrupt context but BLE in progress\n"); return RF_CCA_CLEAR; } #endif if(rf_is_on()) { /* * Wait for potential leftover ACK still being sent. * Strictly speaking, if we are TXing an ACK then the channel is not clear. * However, channel_clear is only ever called to determine whether there is * someone else's packet in the air, not ours. * * We could probably even simply return that the channel is clear */ while(transmitting()); } else { was_off = 1; if(on() != RF_CMD_OK) { PRINTF("channel_clear: on() failed\n"); if(was_off) { off(); } return RF_CCA_CLEAR; } } cca_info = get_cca_info(); if(cca_info == RF_GET_CCA_INFO_ERROR) { PRINTF("channel_clear: CCA error\n"); ret = RF_CCA_CLEAR; } else { /* * cca_info bits 1:0 - ccaStatus * Return 1 (clear) if idle or invalid. */ ret = (cca_info & 0x03) != RF_CMD_CCA_REQ_CCA_STATE_BUSY; } if(was_off) { off(); } return ret; } /*---------------------------------------------------------------------------*/ static int receiving_packet(void) { int ret = 0; uint8_t cca_info; uint8_t was_off = 0; if(!rf_is_on()) { was_off = 1; if(on() != RF_CMD_OK) { PRINTF("receiving_packet: on() failed\n"); return RF_CMD_ERROR; } } /* * If we are in the middle of a BLE operation, we got called by ContikiMAC * from within an interrupt context. We are not receiving */ #if CC26XX_RF_BLE_SUPPORT if(ble_mode_on) { PRINTF("receiving_packet: Interrupt context but BLE in progress\n"); return 0; } #endif /* If we are off, we are not receiving */ if(!rf_is_on()) { PRINTF("receiving_packet: We were off\n"); return 0; } /* If we are transmitting (can only be an ACK here), we are not receiving */ if(transmitting()) { PRINTF("receiving_packet: We were TXing\n"); return 0; } cca_info = get_cca_info(); if(cca_info == RF_GET_CCA_INFO_ERROR) { /* If we can't read CCA info, return "not receiving" */ ret = 0; } else { /* Return 1 (receiving) if ccaState is busy */ ret = (cca_info & 0x03) == RF_CMD_CCA_REQ_CCA_STATE_BUSY; } if(was_off) { off(); } return ret; } /*---------------------------------------------------------------------------*/ static int pending_packet(void) { volatile uint8_t *current = rx_data_queue.pCurrEntry; int rv = 0; /* Go through all RX buffers and check their status */ do { if(GET_FIELD_V(current, dataEntry, status) == DATA_ENTRY_STATUS_FINISHED) { rv = 1; process_poll(&cc26xx_rf_process); } current = GET_FIELD_V(current, dataEntry, pNextEntry); } while(current != rx_data_queue.pCurrEntry); /* If we didn't find an entry at status finished, no frames are pending */ return rv; } /*---------------------------------------------------------------------------*/ static int on(void) { /* * Request the HF XOSC as the source for the HF clock. Needed before we can * use the FS. This will only request, it will _not_ perform the switch. */ oscillators_request_hf_xosc(); /* * If we are in the middle of a BLE operation, we got called by ContikiMAC * from within an interrupt context. Abort, but pretend everything is OK. */ #if CC26XX_RF_BLE_SUPPORT if(ble_mode_on) { PRINTF("on: Interrupt context but BLE in progress\n"); return RF_CMD_OK; } #endif if(rf_is_on()) { PRINTF("on: We were on. PD=%u, RX=0x%04x \n", rf_is_accessible(), RF_RADIO_OP_GET_STATUS(cmd_ieee_rx_buf)); return RF_CMD_OK; } if(power_up() != RF_CMD_OK) { PRINTF("on: power_up() failed\n"); return RF_CMD_ERROR; } if(apply_patches() != RF_CMD_OK) { PRINTF("on: apply_patches() failed\n"); return RF_CMD_ERROR; } init_rx_buffers(); setup_interrupts(); /* * Trigger a switch to the XOSC, so that we can subsequently use the RF FS * This will block until the XOSC is actually ready, but give how we * requested it early on, this won't be too long a wait/ */ oscillators_switch_to_hf_xosc(); if(rf_radio_setup(RF_MODE_IEEE) != RF_CMD_OK) { PRINTF("on: radio_setup() failed\n"); return RF_CMD_ERROR; } return rx_on(); } /*---------------------------------------------------------------------------*/ static int off(void) { /* * If we are in the middle of a BLE operation, we got called by ContikiMAC * from within an interrupt context. Abort, but pretend everything is OK. */ #if CC26XX_RF_BLE_SUPPORT if(ble_mode_on) { PRINTF("off: Interrupt context but BLE in progress\n"); return RF_CMD_OK; } #endif while(transmitting()); power_down(); /* Switch HF clock source to the RCOSC to preserve power */ oscillators_switch_to_hf_rc(); /* We pulled the plug, so we need to restore the status manually */ GET_FIELD(cmd_ieee_rx_buf, radioOp, status) = IDLE; /* * Just in case there was an ongoing RX (which started after we begun the * shutdown sequence), we don't want to leave the buffer in state == ongoing */ GET_FIELD_V(rx_buf_0, dataEntry, status) = DATA_ENTRY_STATUS_PENDING; GET_FIELD_V(rx_buf_1, dataEntry, status) = DATA_ENTRY_STATUS_PENDING; GET_FIELD_V(rx_buf_2, dataEntry, status) = DATA_ENTRY_STATUS_PENDING; GET_FIELD_V(rx_buf_3, dataEntry, status) = DATA_ENTRY_STATUS_PENDING; return RF_CMD_OK; } /*---------------------------------------------------------------------------*/ static radio_result_t get_value(radio_param_t param, radio_value_t *value) { if(!value) { return RADIO_RESULT_INVALID_VALUE; } switch(param) { case RADIO_PARAM_POWER_MODE: /* On / off */ *value = rf_is_on() ? RADIO_POWER_MODE_ON : RADIO_POWER_MODE_OFF; return RADIO_RESULT_OK; case RADIO_PARAM_CHANNEL: *value = (radio_value_t)GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, channel); return RADIO_RESULT_OK; case RADIO_PARAM_PAN_ID: *value = (radio_value_t)GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, localPanID); return RADIO_RESULT_OK; case RADIO_PARAM_16BIT_ADDR: *value = (radio_value_t)GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, localShortAddr); return RADIO_RESULT_OK; case RADIO_PARAM_RX_MODE: *value = 0; if(GET_BITFIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, frameFiltOpt, frameFiltEn)) { *value |= RADIO_RX_MODE_ADDRESS_FILTER; } if(GET_BITFIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, frameFiltOpt, autoAckEn)) { *value |= RADIO_RX_MODE_AUTOACK; } return RADIO_RESULT_OK; case RADIO_PARAM_TXPOWER: *value = get_tx_power(); return RADIO_RESULT_OK; case RADIO_PARAM_CCA_THRESHOLD: *value = GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, ccaRssiThr); return RADIO_RESULT_OK; case RADIO_PARAM_RSSI: *value = get_rssi(); if(*value == RF_CMD_CCA_REQ_RSSI_UNKNOWN) { return RADIO_RESULT_ERROR; } else { return RADIO_RESULT_OK; } case RADIO_CONST_CHANNEL_MIN: *value = CC26XX_RF_CHANNEL_MIN; return RADIO_RESULT_OK; case RADIO_CONST_CHANNEL_MAX: *value = CC26XX_RF_CHANNEL_MAX; return RADIO_RESULT_OK; case RADIO_CONST_TXPOWER_MIN: *value = OUTPUT_POWER_MIN; return RADIO_RESULT_OK; case RADIO_CONST_TXPOWER_MAX: *value = OUTPUT_POWER_MAX; return RADIO_RESULT_OK; default: return RADIO_RESULT_NOT_SUPPORTED; } } /*---------------------------------------------------------------------------*/ static radio_result_t set_value(radio_param_t param, radio_value_t value) { uint8_t was_off = 0; radio_result_t rv; switch(param) { case RADIO_PARAM_POWER_MODE: if(value == RADIO_POWER_MODE_ON) { if(on() != RF_CMD_OK) { PRINTF("set_value: on() failed (1)\n"); return RADIO_RESULT_ERROR; } return RADIO_RESULT_OK; } if(value == RADIO_POWER_MODE_OFF) { off(); return RADIO_RESULT_OK; } return RADIO_RESULT_INVALID_VALUE; case RADIO_PARAM_CHANNEL: if(value < CC26XX_RF_CHANNEL_MIN || value > CC26XX_RF_CHANNEL_MAX) { return RADIO_RESULT_INVALID_VALUE; } GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, channel) = (uint8_t)value; break; case RADIO_PARAM_PAN_ID: GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, localPanID) = (uint16_t)value; break; case RADIO_PARAM_16BIT_ADDR: GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, localShortAddr) = (uint16_t)value; break; case RADIO_PARAM_RX_MODE: { if(value & ~(RADIO_RX_MODE_ADDRESS_FILTER | RADIO_RX_MODE_AUTOACK)) { return RADIO_RESULT_INVALID_VALUE; } GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, frameFiltOpt) = BITVALUE(CMD_IEEE_RX, frameFiltOpt, frameFiltEn, (value & RADIO_RX_MODE_ADDRESS_FILTER) != 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, frameFiltStop, 1) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, autoAckEn, (value & RADIO_RX_MODE_AUTOACK) != 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, slottedAckEn, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, autoPendEn, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, defaultPend, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, bPendDataReqOnly, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, bPanCoord, 0) | BITVALUE(CMD_IEEE_RX, frameFiltOpt, bStrictLenFilter, 0); break; } case RADIO_PARAM_TXPOWER: if(value < OUTPUT_POWER_MIN || value > OUTPUT_POWER_MAX) { return RADIO_RESULT_INVALID_VALUE; } set_tx_power(value); return RADIO_RESULT_OK; case RADIO_PARAM_CCA_THRESHOLD: GET_FIELD(cmd_ieee_rx_buf, CMD_IEEE_RX, ccaRssiThr) = (int8_t)value; break; default: return RADIO_RESULT_NOT_SUPPORTED; } /* If we reach here we had no errors. Apply new settings */ if(!rf_is_on()) { was_off = 1; if(on() != RF_CMD_OK) { PRINTF("set_value: on() failed (2)\n"); return RADIO_RESULT_ERROR; } } if(rx_off() != RF_CMD_OK) { PRINTF("set_value: rx_off() failed\n"); rv = RADIO_RESULT_ERROR; } if(rx_on() != RF_CMD_OK) { PRINTF("set_value: rx_on() failed\n"); rv = RADIO_RESULT_ERROR; } /* If we were off, turn back off */ if(was_off) { off(); } return rv; } /*---------------------------------------------------------------------------*/ static radio_result_t get_object(radio_param_t param, void *dest, size_t size) { uint8_t *target; uint8_t *src; int i; if(param == RADIO_PARAM_64BIT_ADDR) { if(size != 8 || !dest) { return RADIO_RESULT_INVALID_VALUE; } target = dest; src = (uint8_t *)(GET_FIELD_PTR(cmd_ieee_rx_buf, CMD_IEEE_RX, localExtAddr)); for(i = 0; i < 8; i++) { target[i] = src[7 - i]; } return RADIO_RESULT_OK; } return RADIO_RESULT_NOT_SUPPORTED; } /*---------------------------------------------------------------------------*/ static radio_result_t set_object(radio_param_t param, const void *src, size_t size) { uint8_t was_off = 0; radio_result_t rv; int i; uint8_t *dst; if(param == RADIO_PARAM_64BIT_ADDR) { if(size != 8 || !src) { return RADIO_RESULT_INVALID_VALUE; } dst = (uint8_t *)(GET_FIELD_PTR(cmd_ieee_rx_buf, CMD_IEEE_RX, localExtAddr)); for(i = 0; i < 8; i++) { dst[i] = ((uint8_t *)src)[7 - i]; } if(!rf_is_on()) { was_off = 1; if(on() != RF_CMD_OK) { PRINTF("set_object: on() failed\n"); return RADIO_RESULT_ERROR; } } if(rx_off() != RF_CMD_OK) { PRINTF("set_object: rx_off() failed\n"); rv = RADIO_RESULT_ERROR; } if(rx_on() != RF_CMD_OK) { PRINTF("set_object: rx_on() failed\n"); rv = RADIO_RESULT_ERROR; } /* If we were off, turn back off */ if(was_off) { off(); } return rv; } return RADIO_RESULT_NOT_SUPPORTED; } /*---------------------------------------------------------------------------*/ const struct radio_driver cc26xx_rf_driver = { init, prepare, transmit, send, read_frame, channel_clear, receiving_packet, pending_packet, on, off, get_value, set_value, get_object, set_object, }; /*---------------------------------------------------------------------------*/ PROCESS_THREAD(cc26xx_rf_process, ev, data) { int len; PROCESS_BEGIN(); while(1) { PROCESS_WAIT_EVENT(); do { packetbuf_clear(); len = read_frame(packetbuf_dataptr(), PACKETBUF_SIZE); if(len > 0) { packetbuf_set_datalen(len); NETSTACK_RDC.input(); } } while(len > 0); } PROCESS_END(); } /*---------------------------------------------------------------------------*/ #if CC26XX_RF_BLE_SUPPORT /*---------------------------------------------------------------------------*/ /** * \brief Builds common radio parameters for radio operations * * \param *cmd Pointer to buffer to add parameters to * \param command Radio command number (e.g. COMMAND_RADIO_SETUP) * * \note The buffer must be emptied with memset() before calling this function * * \return None */ static void rf_build_ble_radio_op_cmd(uint8_t *cmd, uint16_t command) { GET_FIELD(cmd, radioOp, commandNo) = command; GET_FIELD(cmd, radioOp, status) = IDLE; GET_FIELD(cmd, radioOp, pNextOp) = NULL; GET_FIELD(cmd, radioOp, startTime) = 0; GET_FIELD(cmd, radioOp, startTrigger) = TRIG_NOW; GET_FIELD(cmd, radioOp, condition) = COND_NEVER; } /*---------------------------------------------------------------------------*/ static void init_ble() { ble_mode_on = 0; memset(beacond_config.adv_name, 0, BLE_ADV_NAME_BUF_LEN); beacond_config.interval = BLE_ADV_INTERVAL; } /*---------------------------------------------------------------------------*/ static int send_ble_adv_nc(int channel, uint8_t *output, uint8_t *adv_payload, int adv_payload_len, uint16_t *dev_address) { uint32_t cmd_status; int ret; /* Erase ble_tx_rx_buf array */ memset(ble_tx_rx_buf, 0x00, SIZEOF_RADIO_OP(CMD_BLE_ADV_NC)); rf_build_ble_radio_op_cmd(ble_tx_rx_buf, CMD_BLE_ADV_NC); GET_FIELD(ble_tx_rx_buf, bleRadioOp, channel) = channel; GET_FIELD(ble_tx_rx_buf, bleRadioOp, whitening) = 0; memset(ble_cmd_buf, 0x00, SIZEOF_STRUCT(bleAdvPar)); GET_FIELD(ble_tx_rx_buf, bleRadioOp, pParams) = (uint8_t *)ble_cmd_buf; GET_FIELD(ble_tx_rx_buf, bleRadioOp, pOutput) = output; /* Set up BLE Advertisement parameters */ GET_FIELD(ble_cmd_buf, bleAdvPar, pRxQ) = NULL; GET_FIELD(ble_cmd_buf, bleAdvPar, rxConfig) = 0; GET_FIELD(ble_cmd_buf, bleAdvPar, advConfig) = 0; GET_FIELD(ble_cmd_buf, bleAdvPar, advLen) = adv_payload_len; GET_FIELD(ble_cmd_buf, bleAdvPar, scanRspLen) = 0; GET_FIELD(ble_cmd_buf, bleAdvPar, pAdvData) = adv_payload; GET_FIELD(ble_cmd_buf, bleAdvPar, pScanRspData) = NULL; GET_FIELD(ble_cmd_buf, bleAdvPar, pDeviceAddress) = dev_address; GET_FIELD(ble_cmd_buf, bleAdvPar, pWhiteList) = NULL; GET_FIELD(ble_cmd_buf, bleAdvPar, endTrigger) = TRIG_NEVER; GET_FIELD(ble_cmd_buf, bleAdvPar, endTime) = TRIG_NEVER; if(rf_send_cmd((uint32_t)ble_tx_rx_buf, &cmd_status) == RF_CMD_ERROR) { PRINTF("send_ble_adv_nc: Chan=%d CMDSTA=0x%08lx, status=0x%04x\n", channel, cmd_status, RF_RADIO_OP_GET_STATUS(ble_tx_rx_buf)); return RF_CMD_ERROR; } /* Wait for the ADV_NC to go out */ while((RF_RADIO_OP_GET_STATUS(ble_tx_rx_buf) & RF_RADIO_OP_MASKED_STATUS) == RF_RADIO_OP_MASKED_STATUS_RUNNING); if(RF_RADIO_OP_GET_STATUS(ble_tx_rx_buf) == RF_RADIO_OP_STATUS_BLE_DONE_OK) { /* Sent OK */ ret = RF_CMD_OK; } else { /* Radio Op completed, but ADV NC was not sent */ PRINTF("send_ble_adv_nc: Chan=%d CMDSTA=0x%08lx, status=0x%04x\n", channel, cmd_status, RF_RADIO_OP_GET_STATUS(ble_tx_rx_buf)); ret = RF_CMD_ERROR; } return ret; } /*---------------------------------------------------------------------------*/ static int send_ble_adv(int channel, uint8_t *adv_payload, int adv_payload_len) { if(send_ble_adv_nc(channel, rf_stats, adv_payload, adv_payload_len, (uint16_t *)&linkaddr_node_addr.u8[2]) != RF_CMD_OK) { PRINTF("send_ble_adv: Channel=%d, Error advertising\n", channel); /* Break the loop, but don't return just yet */ return RF_CMD_ERROR; } return RF_CMD_OK; } /*---------------------------------------------------------------------------*/ PROCESS_THREAD(cc26xx_rf_ble_beacon_process, ev, data) { static struct etimer ble_adv_et; static uint8_t payload[BLE_ADV_PAYLOAD_BUF_LEN]; static int p = 0; static int i; uint8_t was_on; int j; uint32_t cmd_status; PROCESS_BEGIN(); while(1) { etimer_set(&ble_adv_et, beacond_config.interval); PROCESS_WAIT_EVENT(); if(ev == PROCESS_EVENT_EXIT) { PROCESS_EXIT(); } /* Set the adv payload each pass: The device name may have changed */ p = 0; /* device info */ payload[p++] = 0x02; /* 2 bytes */ payload[p++] = BLE_ADV_TYPE_DEVINFO; payload[p++] = 0x1a; /* LE general discoverable + BR/EDR */ payload[p++] = 1 + strlen(beacond_config.adv_name); payload[p++] = BLE_ADV_TYPE_NAME; memcpy(&payload[p], beacond_config.adv_name, strlen(beacond_config.adv_name)); p += strlen(beacond_config.adv_name); for(i = 0; i < BLE_ADV_MESSAGES; i++) { /* * Under ContikiMAC, some IEEE-related operations will be called from an * interrupt context. We need those to see that we are in BLE mode. */ ti_lib_int_master_disable(); ble_mode_on = 1; ti_lib_int_master_enable(); /* * Send BLE_ADV_MESSAGES beacon bursts. Each burst on all three * channels, with a BLE_ADV_DUTY_CYCLE interval between bursts * * First, determine our state: * * If we are running NullRDC, we are likely in IEEE RX mode. We need to * abort the IEEE BG Op before entering BLE mode. * If we are ContikiMAC, we are likely off, in which case we need to * boot the CPE before entering BLE mode */ was_on = rf_is_accessible(); if(was_on) { /* * We were on: If we are in the process of receiving an IEEE frame, * abort the BLE beacon burst. Otherwise, terminate the IEEE BG Op * so we can switch to BLE mode */ if(receiving_packet()) { PRINTF("cc26xx_rf_ble_beacon_process: We were receiving\n"); /* Abort this pass */ break; } if(rx_off() != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: rx_off() failed\n"); /* Abort this pass */ break; } } else { /* Request the HF XOSC to source the HF clock. */ oscillators_request_hf_xosc(); /* We were off: Boot the CPE */ if(power_up() != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: power_up() failed\n"); /* Abort this pass */ break; } if(apply_patches() != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: apply_patches() failed\n"); /* Abort this pass */ break; } /* Trigger a switch to the XOSC, so that we can use the FS */ oscillators_switch_to_hf_xosc(); } /* Enter BLE mode */ if(rf_radio_setup(RF_MODE_BLE) != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: Error entering BLE mode\n"); /* Continue so we can at least try to restore our previous state */ } else { /* Send advertising packets on all 3 advertising channels */ for(j = 37; j <= 39; j++) { if(send_ble_adv(j, payload, p) != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: Channel=%d," "Error advertising\n", j); /* Break the loop, but don't return just yet */ break; } } } /* Send a CMD_STOP command to RF Core */ if(rf_send_cmd(CMDR_DIR_CMD(CMD_STOP), &cmd_status) != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: status=0x%08lx\n", cmd_status); /* Continue... */ } if(was_on) { /* We were on, go back to IEEE mode */ if(rf_radio_setup(RF_MODE_IEEE) != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: radio_setup() failed\n"); } /* Enter IEEE RX mode */ if(rx_on() != RF_CMD_OK) { PRINTF("cc26xx_rf_ble_beacon_process: rx_on() failed\n"); } } else { power_down(); /* Switch HF clock source to the RCOSC to preserve power */ oscillators_switch_to_hf_rc(); } etimer_set(&ble_adv_et, BLE_ADV_DUTY_CYCLE); ti_lib_int_master_disable(); ble_mode_on = 0; ti_lib_int_master_enable(); /* Wait unless this is the last burst */ if(i < BLE_ADV_MESSAGES - 1) { PROCESS_WAIT_EVENT(); } } ti_lib_int_master_disable(); ble_mode_on = 0; ti_lib_int_master_enable(); } PROCESS_END(); } /*---------------------------------------------------------------------------*/ #endif /* CC26XX_RF_BLE_SUPPORT */ /*---------------------------------------------------------------------------*/ void cc26xx_rf_ble_beacond_config(clock_time_t interval, const char *name) { #if CC26XX_RF_BLE_SUPPORT if(name != NULL) { memset(beacond_config.adv_name, 0, BLE_ADV_NAME_BUF_LEN); if(strlen(name) == 0 || strlen(name) >= BLE_ADV_NAME_BUF_LEN) { return; } memcpy(beacond_config.adv_name, name, strlen(name)); } if(interval != 0) { beacond_config.interval = interval; } #endif } /*---------------------------------------------------------------------------*/ uint8_t cc26xx_rf_ble_beacond_start() { #if CC26XX_RF_BLE_SUPPORT if(beacond_config.adv_name[0] == 0) { return RF_CMD_ERROR; } process_start(&cc26xx_rf_ble_beacon_process, NULL); return RF_CMD_OK; #else return RF_CMD_ERROR; #endif } /*---------------------------------------------------------------------------*/ void cc26xx_rf_ble_beacond_stop() { #if CC26XX_RF_BLE_SUPPORT process_exit(&cc26xx_rf_ble_beacon_process); #endif } /*---------------------------------------------------------------------------*/ /** @} */