CONTIKI_TARGET_DIRS = . dev apps net loader dev/arduino CONTIKI_CORE=contiki-main CONTIKI_TARGET_MAIN = ${CONTIKI_CORE}.o CONTIKI_TARGET_SOURCEFILES += contiki-main.c params.c node-id.c #Needed for slip CONTIKI_TARGET_SOURCEFILES += led.c sensors.c slip_uart0.c slip.c leds-arch.c CONTIKI_TARGET_SOURCEFILES += temperature-sensor.c adc.c #Needed for Button CONTIKI_TARGET_SOURCEFILES += button-sensor.c # i2c Master #CONTIKI_TARGET_SOURCEFILES += i2c.c #Needed for DHT11 humidity sensor CONTIKI_TARGET_SOURCEFILES += dht11.c #Needed for DS18S20 temperature sensor CONTIKI_TARGET_SOURCEFILES += ds1820.c #Needed for Battery test CONTIKI_TARGET_SOURCEFILES += battery-sensor.c batmon.c #Needed for PIR CONTIKI_TARGET_SOURCEFILES += pir-sensor.c #Needed for OPTRIAC CONTIKI_TARGET_SOURCEFILES += optriac-sensor.c #Needed for SERVO CONTIKI_TARGET_SOURCEFILES += servo.c servo-sensor.c #Needed for Timer4 Servo #CONTIKI_TARGET_SOURCEFILES += t4-servo.c t4-servo-sensor.c #Needed for Relay 1 to 4 CONTIKI_TARGET_SOURCEFILES += relay.c relay-sensor.c # Arduino CONTIKI_TARGET_SOURCEFILES += wiring_digital.c CONTIKI_TARGET_SOURCEFILES += new.cpp twi.c Wire.cpp WMath.cpp CONTIKI_TARGET_SOURCEFILES += Print.cpp Stream.cpp WString.cpp # guh Source Files # Smart Grid Ready Interface CONTIKI_TARGET_SOURCEFILES += sg-ready.c CONTIKIAVR=$(CONTIKI)/cpu/avr CONTIKIBOARD=. BOOTLOADER_START = 0x1F000 CONTIKI_PLAT_DEFS = -DF_CPU=16000000UL -DAUTO_CRC_PADDING=2 -DPLAT_TIMER=5 MCU=atmega128rfa1 #AVRDUDE_PROGRAMMER=jtag2 AVRDUDE_PROGRAMMER=arduino # For usb devices, you may either use PORT=usb, or (e.g. if you have # more than one programmer connected) you can use the following trick to # find out the serial number: # # The example is for an JTAGICE mkII used to program an ATmega128: # avrdude -v -P usb:xxxx -c jtag2 -p atmega128 # AVRDUDE_PORT=usb:00B000000D79 # For serial devices with bootloader we also use the AVRDUDE_PORT setting: AVRDUDE_PORT=/dev/ttyUSB0 # Only needed for serial devices, use empty setting for other # programmers AVRDUDE_BAUD_OPTION=-b 57600 # Additional avrdude options # First some flash options: # Verify off is -V # Erase is -e # No-Erase (needed by some stk500 variants) is -D AVRDUDE_FLASH_OPTIONS=-e AVRDUDE_OPTIONS=$(AVRDUDE_BAUD_OPTION) $(AVRDUDE_FLASH_OPTIONS) AVRDUDE_MCU=m128rfa1 #debug # CFLAGS += -save-temps # Bootloader bonsai # LDFLAGS += -save-temps # For the old bonsai bootloader compiled with squeeze gcc-avr we # directly used the address of the bootloader: #BOOTLOADER_GET_MAC=0x0001f3a0 # For newer bonsai we have a jump table at the end of the bootloader # section: BOOTLOADER_GET_MAC=0x0001ff80 LDFLAGS += -Wl,--defsym,bootloader_get_mac=$(BOOTLOADER_GET_MAC) include $(CONTIKIAVR)/Makefile.avr include $(CONTIKIAVR)/radio/Makefile.radio MODULES += core/net/mac core/net core/net/mac/sicslowmac \ core/net/mac/contikimac core/net/llsec \ # core/net/ipv6 core/net/ipv4 core/net/ip \ # core/net/rime \ # core/net/rpl \