CONTIKI_TARGET_DIRS = .


ifeq ($(USE_SENSOR_BOARD),1)
 COMPILE_SENSORS=TRUE
 CFLAGS += -DCOMPILE_SENSORS
 ${info Compiling with Sensor Files}
else
 COMPILE_SENSORS=FALSE
 ${info NOT compiling Sensor Files}
endif


ifeq ($(USE_SUBGHZ_BOARD),IDS01A4)
  CFLAGS += -DX_NUCLEO_IDS01A4
  ${info Using 868 MHz SPIRIT1 Board}
else ifeq  ($(USE_SUBGHZ_BOARD),IDS01A5)
  CFLAGS += -DX_NUCLEO_IDS01A5
  ${info Using 915 MHz SPIRIT1 Board}
else
  ${info You must specify which SPIRIT1 board you use:}
  ${info make USE_SUBGHZ_BOARD=IDS01A4 for 868 MHz}
  ${info make USE_SUBGHZ_BOARD=IDS01A5 for 915 MHz}
  ${error }
endif


#Currently we support only GCC
GCC=1

CONTIKI_TARGET_DIRS += stm32cube-hal/Src
CONTIKI_TARGET_DIRS += dev
CONTIKI_TARGET_DIRS += drivers/stm32l1xx_nucleo
CONTIKI_TARGET_DIRS += drivers/x_nucleo_ids01ax
CONTIKI_TARGET_DIRS += drivers/Common
CONTIKI_TARGET_DIRS += drivers/spirit1/src drivers/spirit1/inc

ifeq ($(COMPILE_SENSORS),TRUE)
CONTIKI_TARGET_DIRS += drivers/x_nucleo_iks01a1
CONTIKI_TARGET_DIRS += drivers/sensors/hts221 drivers/sensors/lps25h drivers/sensors/lps25hb\
                       drivers/sensors/lsm6ds0 drivers/sensors/lsm6ds3 drivers/sensors/lis3mdl
endif


ARCH_DEV = button-sensor.c leds-arch.c

ARCH_DEV_SENSORS = temperature-sensor.c humidity-sensor.c pressure-sensor.c magneto-sensor.c acceleration-sensor.c gyroscope-sensor.c

ARCH_NUCLEOSPIRIT1 = contiki-spirit1-main.c  uart-msg.c  spirit1-arch.c  spirit1.c node-id.c

ARCH_NUCLEOSPIRIT1_STM32CUBEHAL = spirit1_appli.c  stm32l1xx_hal_msp.c  stm32l1xx_it.c stm32cube_hal_init.c

ARCH_DRIVERS_STM32L1xx = stm32l1xx_nucleo.c

ARCH_DRIVERS_IDS01AX = radio_gpio.c  radio_shield_config.c  radio_spi.c

ARCH_DRIVERS_SPIRIT1 = \
				SPIRIT1_Util.c \
				SPIRIT_Aes.c \
				SPIRIT_Calibration.c \
				SPIRIT_Commands.c \
				SPIRIT_Csma.c \
				SPIRIT_DirectRF.c \
				SPIRIT_General.c \
				SPIRIT_Gpio.c \
				SPIRIT_Irq.c \
				SPIRIT_LinearFifo.c \
				SPIRIT_Management.c \
				SPIRIT_PktBasic.c \
				SPIRIT_PktCommon.c \
				SPIRIT_PktMbus.c \
				SPIRIT_PktStack.c \
				SPIRIT_Qi.c \
				SPIRIT_Radio.c \
				SPIRIT_Timer.c \
				SPIRIT_Types.c

ARCH_DRIVERS_IKS01A1 =  x_nucleo_iks01a1.c  x_nucleo_iks01a1_hum_temp.c  x_nucleo_iks01a1_imu_6axes.c \
		x_nucleo_iks01a1_magneto.c  x_nucleo_iks01a1_pressure.c 

ARCH_DRIVERS_SENSORS =	hts221.c  \
			lis3mdl.c \
			lps25h.c  \
			lps25hb.c \
			lsm6ds0.c \
			lsm6ds3.c

ARCH+=$(ARCH_DEV)
ARCH+=$(ARCH_NUCLEOSPIRIT1)
ARCH+=$(ARCH_NUCLEOSPIRIT1_STM32CUBEHAL)
ARCH+=$(ARCH_DRIVERS_STM32L1xx)
ARCH+=$(ARCH_DRIVERS_IDS01AX)
ARCH+=$(ARCH_DRIVERS_SPIRIT1)

ifeq ($(COMPILE_SENSORS),TRUE)
  ARCH+=$(ARCH_DEV_SENSORS)
  ARCH+=$(ARCH_DRIVERS_IKS01A1)
  ARCH+=$(ARCH_DRIVERS_SENSORS)
endif

CFLAGS += -DUSE_STM32L152_EVAL \
		-DSTM32L152xE \
		-DUSE_STM32L1XX_NUCLEO \
		-DUSE_HAL_DRIVER \
		-DUSE_STDPERIPH_DRIVER \
		-DNO_EEPROM \
		-DSPIRIT1_ST_SHIELD \
		-DSPIRIT_MODULE \
		-DUSE_SPIRIT1_DEFAULT

CFLAGS += -I. \
	  -I$(CONTIKI)/platform/$(TARGET)/ \
	  -I$(CONTIKI)/platform/$(TARGET)/stm32cube-hal/Inc \
	  -I$(CONTIKI)/platform/$(TARGET)/drivers/Common \
	  -I$(CONTIKI)/platform/$(TARGET)/divers/x_nucleo_ids01ax\
	  -I$(CONTIKI)/platform/$(TARGET)/drivers/spirit1/inc \
	  -I$(CONTIKI)/cpu/arm/stm32l152/CMSIS \
	  -I$(CONTIKI)/platform/$(TARGET)/drvers/stm32l1xx_nucleo \
	  -I$(CONTIKI)/cpu/arm/stm32l152/STM32L1xx_HAL_Driver/Inc \
	  -I$(CONTIKI)/cpu/arm/stm32l152 \
	  -I$(CONTIKI)/core                   \
	  -I$(CONTIKI)/platform/$(TARGET)/dev


ifdef UIP_CONF_IPV6
CFLAGS += -DWITH_UIP6=1
endif


ifndef CONTIKI_TARGET_MAIN
CONTIKI_TARGET_MAIN = contiki-spirit1-main.c
endif

CONTIKI_TARGET_SOURCEFILES += $(ARCH) $(CONTIKI_TARGET_MAIN)

MCU=stm32l152
CONTIKI_CPU=$(CONTIKI)/cpu/arm/stm32l152
include $(CONTIKI)/cpu/arm/stm32l152/Makefile.stm32l152


MODULES+=core/net \
         core/net/mac core/net/mac/contikimac \
         core/net/llsec


# build rules ------------------------------------

CLEAN += *.stm32nucleo-spirit1 symbols.c symbols.h contiki-stm32nucleo-spirit1.log 

contiki-$(TARGET).a: ${addprefix $(OBJECTDIR)/,symbols.o}

help:
	@echo A few useful make commands:
	@echo make help - shows this help
	@echo make TARGET=stm32nucleo-spirit1 savetarget - stores selection of target to avoid using TARGET= on every make invokation
	@echo make program.upload - compiles and uploads program to connected board
	@echo make program.upload IAR=1 - uses the IAR compiler instead of gcc (not implemented yet)
	@echo make program.upload NODEID=x - uploads with node_id set to x

# Serialdump rules
ifeq ($(HOST_OS),Windows)
  SERIALDUMP = serialdump-windows
  # this ID is a string with which the node identifies itself as, and is used to
  # find the proper /dev/comX-port in Cygwin to connect to.
  CYGWIN_DEV_ID="stm32nucleo-spirit1 Spirit1 Platform"
# include $(CONTIKI)/tools/cygwin/Makefile.cygwin
endif
ifeq ($(HOST_OS),Darwin)
  SERIALDUMP = serialdump-macos
endif
ifndef SERIALDUMP
  # Assume Linux
  SERIALDUMP = serialdump-linux
endif

# IAR/windows/cygwin only for now; after GCC port, see if stm32flash works with Linux
STLINKCLI=ST-LINK_CLI.exe
%.upload: %.hex
	#Note: this command only uploads to a single connected device
	#$(STLINKCLI) -ME || $(STLINKCLI) -ME || $(STLINKCLI) -ME || $(STLINKCLI) -ME
	$(STLINKCLI) -Q -P $*.hex -V -Run


# devcon requires WinDriverKit, downloadable from microsoft.com
DEVCON=devcon.exe
DEVCON_ALLDEVS=$(shell $(DEVCON) find =USB | grep "STMicroelectronics STLink dongle" | cut -d " " -f 1)
devcon_enableonly:
	devcon disable =USB @"USB\VID_0483&PID_3748\*"
	devcon enable =USB @"$(ID)"

%.uploadall: %.hex
	$(foreach D,$(DEVCON_ALLDEVS), echo D IS "$(D)" && make devcon_enableonly ID="$(D)" && make $*.upload && ) echo "Done"
	devcon enable =USB @"USB\VID_0483&PID_3748\*"

login:
	@echo "Connecting to $(COMPORT)"
	$(CONTIKI)/tools/sky/$(SERIALDUMP) -b115200 $(COMPORT)

%.ramusage: %.$(TARGET)
	$(NM) -S $< --size-sort --line-numbers | grep -v " T " | grep -v " t "
%.romusage: %.$(TARGET)
	$(NM) -S $< --size-sort --line-numbers | grep -v " b " | grep -v " B " | grep -v " d " | grep -v " D "