#define GPIO_FUNC_SEL0 0x80000018 /* GPIO 15 - 0; 2 bit blocks */ #define BASE_UART1 0x80005000 #define UART1_CON 0x80005000 #define UART1_STAT 0x80005004 #define UART1_DATA 0x80005008 #define UR1CON 0x8000500c #define UT1CON 0x80005010 #define UART1_CTS 0x80005014 #define UART1_BR 0x80005018 #include "maca.h" #include "embedded_types.h" #define reg(x) (*(volatile uint32_t *)(x)) #define DELAY 400000 #define DATA 0x00401000; #define NL "\033[K\r\n" void putc(uint8_t c); void puts(uint8_t *s); void put_hex(uint8_t x); void put_hex16(uint16_t x); void put_hex32(uint32_t x); const uint8_t hex[16]={'0','1','2','3','4','5','6','7', '8','9','a','b','c','d','e','f'}; void magic(void) { #define X 0x80009a000 #define Y 0x80009a008 #define VAL 0x0000f7df volatile uint32_t x,y; x = reg(X); /* get X */ x &= 0xfffeffff; /* clear bit 16 */ reg(X) = x; /* put it back */ y = reg(Y); /* get Y */ y |= VAL; /* or with the VAL */ x = reg(X); /* get X again */ x |= 16; /* or with 16 */ reg(X) = x; /* put X back */ reg(Y) = y; /* put Y back */ } uint32_t ackBox[10]; #define command_xcvr_rx() \ do { \ maca_txlen = (uint32_t)1<<16; \ maca_dmatx = (uint32_t)&ackBox; \ maca_dmarx = DATA; \ maca_tmren = (maca_cpl_clk | maca_soft_clk); \ maca_control = (control_prm | control_asap | control_seq_rx); \ }while(FALSE) void dump_regs(uint32_t base, uint32_t len) { volatile uint32_t i; puts("base +0 +4 +8 +c +10 +14 +18 +1c \n\r"); for (i = 0; i < len; i ++) { if ((i & 7) == 0) { put_hex16(4 * i); } puts(" "); put_hex32(reg(base+(4*i))); if ((i & 7) == 7) puts(NL); } puts(NL); } __attribute__ ((section ("startup"))) void main(void) { uint8_t c; volatile uint32_t i; uint32_t tmp; volatile uint32_t *data; uint16_t status; /* Restore UART regs. to default */ /* in case there is still bootloader state leftover */ reg(UART1_CON) = 0x0000c800; /* mask interrupts, 16 bit sample --- helps explain the baud rate */ /* INC = 767; MOD = 9999 works: 115200 @ 24 MHz 16 bit sample */ #define INC 767 #define MOD 9999 reg(UART1_BR) = INC<<16 | MOD; /* see Section 11.5.1.2 Alternate Modes */ /* you must enable the peripheral first BEFORE setting the function in GPIO_FUNC_SEL */ /* From the datasheet: "The peripheral function will control operation of the pad IF */ /* THE PERIPHERAL IS ENABLED. */ reg(UART1_CON) = 0x00000003; /* enable receive and transmit */ reg(GPIO_FUNC_SEL0) = ( (0x01 << (14*2)) | (0x01 << (15*2)) ); /* set GPIO15-14 to UART (UART1 TX and RX)*/ reset_maca(); radio_init(); flyback_init(); vreg_init(); init_phy(); /* some kind of sequence in init phy from MACPHY.a dissassmbly */ // magic(); reg(MACA_CONTROL) = SMAC_MACA_CNTL_INIT_STATE; for(i=0; i> 8) << 2; /* write "last warmdown data" to current TSM step to shutdown rx */ LastWarmdownData = (*((volatile uint32_t *)(0x80009300 + LastWarmdownStep))); puts("LastWarmdownData: "); put_hex32(LastWarmdownData); puts(NL); status = reg(MACA_STATUS) & 0x0000ffff; switch(status) { case(cc_aborted): { puts("aborted\n\r"); ResumeMACASync(); command_xcvr_rx(); break; } case(cc_not_completed): { puts("not completed\n\r"); ResumeMACASync(); break; } case(cc_success): { puts("success\n\r"); break; } default: { puts("status: "); put_hex16(status); ResumeMACASync(); command_xcvr_rx(); } } /* reg(MACA_CONTROL) = 0x00031a04; /\* receive *\/ */ /* while (((tmp = reg(MACA_STATUS)) & 15) == 14) */ /* puts("."); */ /* puts("complete status is "); put_hex32(tmp); puts(NL); */ /* puts("1 status is "); put_hex32(reg(MACA_STATUS)); puts(NL); */ /* puts("2 status is "); put_hex32(reg(MACA_STATUS)); puts(NL); */ /* puts("3 status is "); put_hex32(reg(MACA_STATUS)); puts(NL); */ /* puts(NL); */ /* for(i=0; i> 4]); putc(hex[x & 15]); } void put_hex16(uint16_t x) { put_hex((x >> 8) & 0xFF); put_hex((x) & 0xFF); } void put_hex32(uint32_t x) { put_hex((x >> 24) & 0xFF); put_hex((x >> 16) & 0xFF); put_hex((x >> 8) & 0xFF); put_hex((x) & 0xFF); }