Commit graph

7 commits

Author SHA1 Message Date
Brad Campbell af27d2d252 [CC2538-SPI] Implement SPI_FLUSH, spi mode, !CS
Because the CC2538 has a multi-byte SPI RX FIFO, flushing the buffer
requires more than just a single read. This adds a loop that empties the
entire RX buffer on a FLUSH().

Different SPI chips needs different SPI settings. This commit adds a
function that allows chip drivers to configure the SPI peripheral before
using it.

The frame pin the driver was using as a chip select does not work as
most devices expect it to. It toggles after every byte, and most chips
interpret that as end of message. To make drivers more reliable, each
chip driver should setup a GPIO and assert it as needed.
2014-04-15 14:07:10 -04:00
Benoît Thébaudeau dbba311270 cc2538: Add adc driver and example
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-12-06 22:07:45 +01:00
Benoît Thébaudeau d2f3795a30 cc2538: Clean up port and pin definitions
Homogenize port and pin definitions naming:
 - PERIPHERAL_FUNCTION_PORT for the port ID,
 - PERIPHERAL_FUNCTION_PIN for the pin ID,
 - PERIPHERAL_FUNCTION_PORT_BASE for the port base,
 - PERIPHERAL_FUNCTION_PIN_MASK for the pin mask.

Define only PERIPHERAL_FUNCTION_PORT and PERIPHERAL_FUNCTION_PIN in board.h, and
deduce PERIPHERAL_FUNCTION_PORT_BASE and PERIPHERAL_FUNCTION_PIN_MASK in the
driver from the former definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-25 15:00:41 +01:00
Benoît Thébaudeau 680050861c cc2538: gpio: Use accessor macros
Use the GPIO accessor macros instead of copying raw register access code all
over the place. This is cleaner and less error prone.

This fixes the setting of the USB pull-up resistor that worked only by chance on
the CC2538DK because it is controlled by the pin 0 of the used GPIO port.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-11-15 19:57:44 +01:00
Brad Campbell e2af903d05 Added SPI driver for CC2538
This uses the core/dev/spi.h header and implements the spi_init()
function and the various macros for SPI operation. ssi.h contains all of
the register locations and information.

This implementation is not very versatile, mostly because I don't how to
make it flexible in the contiki system. It supports pin muxing for the
four spi pins, but other than that picks sensible defaults.

The SPI macros (like SPI_READ()) are defined in
cpu/cc2538/spi-arch.h. In order to use the SPI driver, add the following
includes to your project:

    #include "spi-arch.h
    #include "dev/spi.h"
2013-09-27 17:46:15 -04:00
George Oikonomou 6c6013b898 Make the CC2538 UART driver more configurable
* We can now very easily switch between UART0 and UART1 through a define
* We can also configure the UART RX and TX port/pin through defines
2013-08-09 12:20:25 +01:00
George Oikonomou 40f49948e6 New Platform: TI CC2538 Development Kit
This commit adds cpu, platform and example files,
providing support for running Contiki on TI's cc2538 DK
2013-04-06 21:07:31 +01:00