The pending GPIO power-up interrupts have to be cleared in the ISRs in order not
to re-trigger the interrupts and the wake-up events.
The power-up interrupts of all pins are cleared for each port in the
corresponding port ISR. This is done after calling the registered callbacks so
that the callbacks can know which pin woke up the SoC. This is done after
clearing the regular interrupt in order to avoid getting a new wake-up interrupt
without the regular interrupt in the case of a new wake-up edge occurring
between the two clears.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The GPIO power-up interrupts have to be configured and enabled in order to be
able to wake-up the SoC from PM1+ upon a signal edge occurring on a GPIO input
pin.
This set of macros allows to:
- configure the signal edge triggering a power-up interrupt,
- enable and disable a power-up interrupt,
- clear a power-up interrupt flag.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
If PM2 is enabled with LPM_CONF_MAX_PM, but not active, the non-retention area
of the SRAM can be useful to place temporary data that does not fit in the
low-leakage SRAM, typically after having called lpm_set_max_pm(LPM_PM1). Hence,
give access to this non-retention area thanks to .nrdata* sections.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The data sheet recommends that the USB pull-up resistor be driven by a GPIO so
that it can be controlled by software, but this is not mandatory. Hence, leave
the choice so that CC253-based boards not using this option can build and work
fine.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Homogenize port and pin definitions naming:
- PERIPHERAL_FUNCTION_PORT for the port ID,
- PERIPHERAL_FUNCTION_PIN for the pin ID,
- PERIPHERAL_FUNCTION_PORT_BASE for the port base,
- PERIPHERAL_FUNCTION_PIN_MASK for the pin mask.
Define only PERIPHERAL_FUNCTION_PORT and PERIPHERAL_FUNCTION_PIN in board.h, and
deduce PERIPHERAL_FUNCTION_PORT_BASE and PERIPHERAL_FUNCTION_PIN_MASK in the
driver from the former definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Use the GPIO accessor macros instead of copying raw register access code all
over the place. This is cleaner and less error prone.
This fixes the setting of the USB pull-up resistor that worked only by chance on
the CC2538DK because it is controlled by the pin 0 of the used GPIO port.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Introduce new useful GPIO macros to:
- read the levels of some port pins,
- write the levels of some port pins (pass bit-field value to be set),
- clear the interrupt flags for some port pins.
These macros are cleaner and less error prone than raw register access code
copied all over the place.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The parameters in the GPIO macros were used without being parenthesized. This
could generate wrong values for register assignments in the case of expressions
passed as arguments to these macros.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
lpm_enter() must not enter PM1+ if the UART TX FIFO is not empty. Otherwise, the
UART clock gets disabled, and its TX is broken.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Some peripherals have their clocks automatically gated in PM1+ modes, so they
cannot operate. This new mechanism gives peripherals a way to prohibit PM1+
modes so that they can properly complete their current operations before
entering PM1+.
This mechanism is implemented with peripheral functions registered to the LPM
module. These functions return whether the associated peripheral permits or not
PM1+ modes. They are called by the LPM module each time PM1+ might be possible.
If any of the peripherals wants to block PM1+, then the system is only dropped
to PM0.
Partly from: George Oikonomou
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
spi-arch.h configures dev/spi.h, so it must be #included first. Luckily, this
mistake did not have any consequence here, but fix it in order to avoid possible
future issues.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
If the SSI has never been used and spi_init() is called, then the SSI receive
FIFO is empty and remains so, so calling SPI_WAITFOREORx() at the end of
spi_init() waits endlessly for SSI_SR.RNE to be set. Hence, this call must be
removed in order to avoid a deadlock.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
ELF files generated by GCC make SmartRF Flash Programmer 2 crash (only the TI
format is supported by this tool for ELFs), and binary files are not very
appropriate because they are gapless, so generate Intel HEX files since these
are very well supported by most programming tools while still flexible.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This uses the core/dev/spi.h header and implements the spi_init()
function and the various macros for SPI operation. ssi.h contains all of
the register locations and information.
This implementation is not very versatile, mostly because I don't how to
make it flexible in the contiki system. It supports pin muxing for the
four spi pins, but other than that picks sensible defaults.
The SPI macros (like SPI_READ()) are defined in
cpu/cc2538/spi-arch.h. In order to use the SPI driver, add the following
includes to your project:
#include "spi-arch.h
#include "dev/spi.h"
Historically $(OBJECTDIR) was created when Makefile.include is read. A
consequence is that combining "clean" with "all" (or any other build
target) results in an error because the clean removes the object
directory that is required to exist when building dependencies.
Creating $(OBJECTDIR) on-demand ensures it is present when needed.
Removed creation of $(OBJECTDIR) on initial read, and added an order-only
dependency forcing its creation all Makefile* rules where the target is
explicitly or implicitly in $(OBJECTDIR).
- For the CC2538, simplify handling of USB_CDC_ACM_LINE_STATE
events. Ignore the Carrier Control (RTS) bit when receiving
a SET_CONTROL_LINE _STATE request, we are a full duplex device.
- Improve behaviour of the CC2531 USB stick when there is no
process on the host to read IN data. Basically, we adopt the
CC2538 approach and we only send data when a DTE is present
