This patch fixes UART system call authorization initialization (when
protection domain support is enabled) to only initialize the system call
entrypoint and authorization data structures once, prior to per-port
setup. Previously, if two UARTs were configured, the setup procedure for
the second UART would erase the system call authorization for the
first (console) UART, resulting in a crash upon the next attempt to
perform console output.
This patch adds a Dockerfile for building a container configured as a
build environment for Intel Galileo boards. This patch also provides
documentation for using the containerized build environment. Finally, it
streamlines the instructions for booting Contiki on Galileo and includes
other documentation refinements.
#1684 slightly varied RF startup time and, as a result, threw ContikiMAC timing configuration off. This manifests itself with very poor CC13xx PROP mode radio performance, as documented in #1747.
This pull fixes this bug by slightly increasing ContikiMAC's inter-packet interval. This gives the receiver a little more time to respond with an ACK to unicast frames.
Fixes#1747
`CC2650_FAST_RADIO_STARTUP` is required for TSCH, but it currently breaks ContikiMAC. We set the default value to the one that will work with the default choice of RDC.
Fixes#1744
This adds support for flashing to multiple devices, by implementing the
$MOTES option used by the Z1.
This replaces the $PORT interface, as it only allowed flashing to one
device at a time, and the $MOTES interface was still used for other
tasks (such as getting a list of connected devices).
A foreach loop is used to dynamically create an upload rule per device
that needs to be flashed.
The "main" upload rule depends on the device specific ones.
This allows for parallel flashing.
The PORT variable can still be sued for backwards compatibility.
Changed the MOTES variable that makes a $(shell) call to not be
recursively expanded.
- platform/atarixl/Makefile.atarixl: put two more objects into high memory
- platform/atarixl/contiki-conf.h: define WWW_CONF_WGET_EXEC
- tools/6502/Makefile: add 'clean' target; remove unused CONTIKI define
Change certain CPP conditionals into C conditionals, which should be possible for the compiler to optimize at runtime. This makes the source code easier to read.
According to the CC1310LP design files, the flash on it is the same as the flash on the CC2650 LP (MX25R8035F 8Mbit). However, the flash on some CC1310 LPs reportedly identifies itself as the 16Mbit one (MX25R1635F). Instruction sets are identical, we simply need to tell the driver to recognise this part's Device ID.
The block that controls the `.upload` target is unnecessarily replicated in multiple sub-board Makefiles. This was originally done because the SmartRF and the Launchpad can be programmed with the c2538-bsl script, whereas the sensortag cannot.
This commit moves the `cc2538-bsl` / `.upload` target logic to the top level cpu Makefile (`cpu/cc26xx-cc13xx/Makefile.cc26xx-cc13xx`). Board makefiles simply set the make variable `BOARD_SUPPORTS_BSL` to 1 to signal that they can be programmed by the BSL script. If `BOARD_SUPPORTS_BSL` is not equal to 1, trying to use the `.upload` target will return an error message.
For example:
```
$ make BOARD=sensortag/cc2650 cc26xx-demo.upload
using saved target 'srf06-cc26xx'
This board cannot be programmed with the ROM bootloader and therefore does not support the .upload target.
```
Two errors have been spotted, when IPv6 is enabled in the ravenusb
Project-Makefile:
#CONTIKI_NO_NET=1
CONTIKI_WITH_IPV6=1
The compile error results from a variable name mismatch in cdc_task.c
The variable 'r' is undeclared and should be renamed to 'route'
The linker also fails with 'undefined references'
This has been mediated by adding 'core/net' to Modules in the
Project-Makefile.
Rename guhRF platform to osd-merkur-256, previous osd-merkur platform is
now osd-merkur-128. Also check that everything is consistent.
Add both platforms to the regression tests.
Move redundant files in platform dev directory of both platforms to
cpu/avr/dev. Note that this probably needs some rework. Already
discovered some inconsistency in io definitions of both devices in the
avr/io.h includes. Added a workaround in the obvious cases.
The platform makefiles now set correct parameters for bootloader and for
reading mac-address from flash memory.
Factor the flash programming into cpu/avr and platform/osd-merkur* and
rework *all* osd example makefiles to use the new settings. Also update
all the flash.sh and run.sh to use the new settings.
The suli ledstrip modules (and osd example) have also been removed.
