adamdunkels
efeb9944fa
Increase the required non-activity periods before turning off the radio; remove the strict phase requirement (which messes up things with low-power streaming)
2010-03-17 16:35:52 +00:00
adamdunkels
9be1a65211
Don't set the RELIABLE flag on incoming packets with the ack requested flag set, since it is set on most packets even if they aren't reliable
2010-03-16 18:11:58 +00:00
adamdunkels
b1feac5a00
Bugfixes in low-power streaming mode, and re-added support for announcements. These now use the low-power streaming mode so that active listening for announcments have a radio duty cycle of 16% rather than 100%
2010-03-16 18:11:13 +00:00
adamdunkels
7bab9316da
Two major changes:
...
* Low-power streaming. Experimental support for a low-power mode which
allows rapid exchange of packets with a 16% duty cycle. Does not
seem to function correctly yet though.
* Phase locking. When the phase of a neighbor has been detected, the
sender assumes that the neighbor will keeps it phase and does not
send more strobes than necessary to hit the receiver's channel
check - even if the receiver does not acknowledge the reception of
the strobes when it should have been awake. Instead, the sender
stops strobing and tries again at a later time.
2010-03-14 22:59:23 +00:00
oliverschmidt
def540e6c0
Avoid newlines in macro expansions as cc65 doesn't support them between the macro name and the open parenthesis of the arguments.
...
There were btw other even longer lines with expansions of the same macro already present.
2010-03-14 12:13:54 +00:00
nifi
2cf0fb9cce
Changed to use short address mode with short rime addresses
2010-03-12 14:49:21 +00:00
adamdunkels
4b60301727
Don't set the ack flag for broadcast packets
2010-03-09 20:40:11 +00:00
adamdunkels
17f6b3a324
Simplified the structure of the code
2010-03-09 20:38:55 +00:00
adamdunkels
d0e6436a20
Don't call up the netstack if the transmission was deferred
2010-03-09 20:37:02 +00:00
adamdunkels
edda6dd86c
Minor bugfix: don't subtract collisions and deferrals from the number of transmissions
2010-03-09 13:23:58 +00:00
adamdunkels
2c3d3e3d73
Bugfix: handle deferred transmissions correctly (don't count them)
2010-03-09 13:20:08 +00:00
adamdunkels
79722b4247
Rework of the timing conditions of ContikiMAC: the old timing did not work well on real hardware, the new one seems to work better
2010-03-09 13:19:05 +00:00
nvt-se
96eb20d235
forward arguments even if REXMIT is not set
2010-03-04 14:17:43 +00:00
nifi
5e43a6998b
Replaced old framer (framer_get/framer_set) with new NETSTACK style configuration. Added nullrdc-framer that is a nullrdc with framer support.
2010-03-01 13:30:21 +00:00
nifi
0c084b8c68
added random init of sequence number
2010-03-01 13:17:01 +00:00
adamdunkels
410d860a93
Improved handling of neighbor phase estimation: instead of busy-waiting while waiting for neighbor's phase, the new code schedules a timer just before neighbor wakes up
2010-02-28 20:19:47 +00:00
adamdunkels
e6fceb7200
Added MAC-layer return value to indicate that a packet transmission was deferred
2010-02-28 20:18:30 +00:00
adamdunkels
e06acc4525
Prod the watchdog if waiting for along time
2010-02-28 14:15:16 +00:00
adamdunkels
74da90a06b
Don't count collisions as transmissions
2010-02-28 10:07:17 +00:00
adamdunkels
b6b4941871
Made the number of MAC-layer retransmissions configurable on a per-packet basis, via a packet attribute
2010-02-28 08:35:16 +00:00
adamdunkels
ed88f487c8
Improved detection of link-layer ACKs; increased the time ContikiMAC waits when it has detected a link-layer ACK; increased the number of silence periods required to detect a CCA false positive
2010-02-28 08:33:21 +00:00
nifi
b50d47fb80
added missing function in sicslowmac_driver
2010-02-23 22:45:11 +00:00
nifi
1cfcc8a73a
Removed the combined name of CSMA and NETSTACK_RDC. The name of NETSTACK_RDC can be accessed separately if needed.
2010-02-23 20:42:45 +00:00
nifi
c20047f657
Changed the network stack to use different structures for the different layers (network_driver, mac_driver, rdc_driver, radio_driver). This helps to avoid incorrect configuration.
2010-02-23 20:09:11 +00:00
adamdunkels
bb62749de7
Made debug printfs optional
2010-02-23 18:49:58 +00:00
adamdunkels
0ab2ba433f
Bugfix: the wrong callback pointer was passed to higher layers.
2010-02-23 18:49:45 +00:00
adamdunkels
ed52586e18
Rework of parts of the ContikiMAC code based on input from experimental results. When channel check is triggered because of a false positive, the new version checks the radio several times to make sure that there really is an incoming packet. Otherwise, the radio is switched off. Cleaned up and removed old unused code. Added a few temporary debugging mechanisms and functions.
2010-02-23 18:49:05 +00:00
adamdunkels
0b2b7bcdba
Removed inadvertedly left-over include file
2010-02-18 23:52:34 +00:00
adamdunkels
e34eb54960
A work-in-progress rework of the Contiki MAC and radio layers. The
...
main ideas are:
* Separates the Contiki low-layer network stack into four layers:
network (e.g. sicslowpan / rime), Medium Access Control MAC
(e.g. CSMA), Radio Duty Cycling RDC (e.g. ContikiMAC, X-MAC), and
radio (e.g. cc2420).
* Introduces a new way to configure the network stack. Four #defines
that specify what mechanism/protocol/driver to use at the four
layers: NETSTACK_CONF_NETWORK, NETSTACK_CONF_MAC, NETSTACK_CONF_RDC,
NETSTACK_CONF_RADIO.
* Adds a callback mechanism to inform the MAC and network layers about
the fate of a transmitted packet: if the packet was not possible to
transmit, the cause of the failure is reported, and if the packets
was successfully transmitted, the number of tries before it was
finally transmitted is reported.
* NULL-protocols at both the MAC and RDC layers: nullmac and nullrdc,
which can be used when MAC and RDC functionality is not needed.
* Extends the radio API with three new functions that enable more
efficient radio duty cycling protocols: channel check, pending
packet, and receiving packet.
* New initialization mechanism, which takes advantage of the NETSTACK
#defines.
2010-02-18 21:48:39 +00:00
adamdunkels
f8c804e28b
ntikiMAC: a new radio duty cycling mechanism that uses a combination
...
of link-layer and MAC-layer mechanisms to achieve a very low power
consumption: during idle listening the radio is switched off between
99.2% and 99.6% of the time. One unicast transmission typically adds
between 0.07% and 1.2% additional radio time, depending on packet
size.
ContikiMAC uses the standard IEEE 802.15.4 message format and adds no
additional headers.
ContikiMAC is simple: it uses periodic two-shot channel sampling
during idle listening to keep the radio on-time down. Transmissions
are done with repeated transmissions until a link-layer ACK is
received.
2010-02-18 21:26:15 +00:00
adamdunkels
f5c48751b5
Reworked 802.15.4 header creation and parsing so that it works regardless of the size of the rimeaddr_t typedef
2010-02-18 21:00:28 +00:00
adamdunkels
2fbf21b2b3
Refactored the phase optimization functionality into a separate module
2010-02-18 20:58:59 +00:00
adamdunkels
75e1c0c8c7
Include contiki-conf.h to let the MAC channel check rate be configurable
2010-02-03 16:45:12 +00:00
adamdunkels
06d17c7e1c
Remove unused rtimer code
2010-02-03 16:44:43 +00:00
adamdunkels
e419eb3cc5
Retransmit packet if it didn't receive a MAC layer ack
2010-02-03 01:17:54 +00:00
adamdunkels
d68af249ec
Added a MAC layer return value that informs the caller that a packet did not receive a MAC layer acknowledgement
2010-02-03 01:17:32 +00:00
adamdunkels
181213124b
Added a configuration option for setting the MAC channel check rate (which must be a power of two). The configuration is independent of the MAC protocol.
2010-02-02 23:28:58 +00:00
adamdunkels
fcf60e9260
Removed the csma_init declaration in the mac_driver struct since it isn't needed and it breaks sdcc
2010-02-02 20:45:58 +00:00
adamdunkels
cc2be0f111
Remove compiler warnings
2010-02-02 16:33:07 +00:00
adamdunkels
1a13d25d33
Revised version of the X-MAC implementation that uses a ctimer instead
...
of an rtimer for the periodic radio duty cycling. The benefit of this
implementation is that it leaves an rtimer free for user tasks. The
drawback is a slightly higher idle power consumption. This new version
is based on the current rtimer-based X-MAC.
2010-01-31 18:44:23 +00:00
adamdunkels
e4168db633
Bugfix: deallocate queuebuf only if there was no collision
2010-01-31 13:55:36 +00:00
adamdunkels
2ae7ed827c
Increase the default X-MAC channel check rate to 4 Hz instead of 2 Hz
2010-01-28 13:40:47 +00:00
adamdunkels
8430dab039
Typecast to fix nightly build problem
2010-01-27 07:36:31 +00:00
adamdunkels
4f3e8d565c
Added a simple CSMA (Carrier Sense Multiple Access) mechanism that
...
works on top of an underlying duty cycling mechanism. The CSMA layer
retransmits packets that could not be sent because of a collision was
detected.
2010-01-25 11:46:44 +00:00
adamdunkels
7ad93e5d18
Added a field to the struct mac interface:
...
channel_check_interval(). This function returns the interval by which
the duty cycling mechanism checks the radio channel for activity. It
is used by higher layer mechanisms to determine suitable timeouts for
retransmissions.
2010-01-25 11:43:32 +00:00
adamdunkels
743e93e650
Do not remove encounters - there is no need to, as they are only an optimization
2010-01-14 20:14:03 +00:00
adamdunkels
2f105e933a
Variable xmac_is_on was used both in interrupt and non-interrupt contexts and needs to be volatile
2009-12-06 23:29:38 +00:00
adamdunkels
53457eb1f0
Fixed compilation warning
2009-12-06 17:10:54 +00:00
adamdunkels
8bcc838d8a
Bugfix: don't set the 'we are sending' flag until we are actually sending
2009-12-06 17:05:45 +00:00
adamdunkels
6897270289
Bugfix to the Contiki LPP encounter timing code: encounters are now
...
properly timed.
2009-12-06 13:18:32 +00:00
adamdunkels
822149f943
Significant improvements to the Contiki X-MAC:
...
* the code is simplified, particularly the duty cycling logic
* old unused code has been removed
* Contiki X-MAC now listens before sending a strobe to avoid MAC-level
collisions
* broadcasts are sent directly, without strobes, reducing the power
consumption of receivers
* turn off radio for 1 ms between sending a strobe and expecting the
strobe ack
2009-12-06 13:16:59 +00:00
adamdunkels
cef2e65c9b
Added an error type for signalling a MAC-layer collision
2009-12-05 21:49:51 +00:00
adamdunkels
4a1a823a49
Code style fix
2009-12-05 13:29:41 +00:00
fros4943
a1b4597b95
fixed announcement compilation error
2009-11-27 14:27:50 +00:00
adamdunkels
aeefa75304
Fixed alignment problems in announcement packet creation
2009-11-27 12:49:27 +00:00
fros4943
0034fd7bca
generic return values for sent packet
2009-11-13 10:09:02 +00:00
fros4943
26bb5ecd21
added radio and MAC generic return values to allow applications finding out whether the packet was transmitted
2009-11-13 08:59:22 +00:00
adamdunkels
70fc23ac7e
Enable stream mode by default, remove LED debug mode
2009-11-04 16:02:45 +00:00
adamdunkels
5aab2eb77d
A simple addition with significant performance implications:
...
sicslowpan tags TCP packets with the PACKETBUF_ATTR_PACKET_TYPE_STREAM
flag, which makes the underlying power-saving MAC layer keep the radio
on for some time after transmitting the packet. This allows reply
packets to be processed directly, significantly increasing TCP latency
and throughput.
2009-11-02 11:58:56 +00:00
nifi
223fa1c8e5
added missing include
2009-10-20 07:42:03 +00:00
adamdunkels
7cdfbca973
Alignment problems with announcements fixed
2009-10-19 21:27:02 +00:00
adamdunkels
9ec57d61ad
Added MAC layer framing support to X-MAC so that packets now are standard 802.15.4 frames
2009-10-19 20:53:56 +00:00
adamdunkels
4de1816e36
Added a new module called "framer" that creates MAC level frames to
...
the packetbuf from packet attributes. Two framer modules are included,
one that creates 802.15.4 frame headers, and one that creates a
minimal "nullmac"-style header that only contains the link-local
addresses.
2009-10-19 18:30:03 +00:00
nifi
ae226c5917
* Set sender and receiver packet attributes on incoming packets
...
* Added link layer destination check
2009-10-19 11:25:54 +00:00
adamdunkels
10c873018d
Ensure that DEFAULT_PERIOD is != 0, to avoid a modulo with 0
2009-10-19 06:39:29 +00:00
adamdunkels
9d26bd663e
A new optimization to X-MAC: senders now keep track of when neighbors
...
last were known to be awake. When sending a packet, a sender does not
start to send strobes until the neighbor is expected to be awake. This
reduces power consumption for senders and decreases the contention in
the network as there are less packets in the air. Additionally, the
ACK optimization was improved so that data/ack exchanges now are
more efficient.
2009-10-18 13:19:25 +00:00
nifi
0ad51b8dcc
Moved the link layer destination check to sicslowmac
2009-09-18 16:37:17 +00:00
adamdunkels
2181e90f69
Added the possibility to switch lpp off. Fixed sdcc compiler issue
2009-09-09 21:09:23 +00:00
adamdunkels
1cafbc6002
sdcc compiler issue fix: compound assignments are not supported, so we use memcpy() instead
2009-09-09 21:08:46 +00:00
nvt-se
4d21a3e203
Don't assume that radio->send turns on the radio automatically.
2009-09-04 10:59:30 +00:00
adamdunkels
522f991f14
Set sender and receiver packet attributes on incoming packets: patch by Gidon Ernst
2009-08-20 18:59:17 +00:00
nifi
912aba7280
added init function in MAC driver for easier configuration
2009-06-22 11:14:11 +00:00
nifi
f39d2bd4c6
Fixed link panid for broadcasts to be standard compliant. Ignore packets addressed to other non-broadcast panids.
2009-05-26 12:08:29 +00:00
adamdunkels
fe5a1f1068
Added an optimization option that avoids multiple simultaneous broadcasts from neighbors: when a broadcast is to be sent, a sender does not send until it knows that no other nodes are broadcasting.
2009-05-10 21:09:05 +00:00
adamdunkels
0adceb63b4
Code cleanup; made encounter optimization explicit; added optimization for adaptive off-time, but it currently seems to work bad with broadcasts
2009-05-06 15:06:38 +00:00
adamdunkels
9fff85757d
Code cleanup; made strobe transmission time longer again (seems to work better in cooja?)
2009-05-06 15:05:28 +00:00
adamdunkels
cc44e89415
Reduced default strobe time, which seems to work well. Avoid running the interrupt if the power-save feature is turned off (fixes problems with serial data reception on a gateway mote)
2009-04-29 11:42:13 +00:00
adamdunkels
81ef83b856
Added option to wait randomly before sending a packet. A few code cleanups. Avoid switching radio off when sending a packet with end-to-end acks, because an ACK may arrive shortly after the transmission.
2009-04-28 14:00:53 +00:00
nifi
84b38de494
removed bitfields for compatibility with cc65
2009-04-09 21:54:09 +00:00
nvt-se
03cd533712
made LISTEN_TIME and OFF_TIME configurable.
2009-04-07 11:29:08 +00:00
adamdunkels
5e456aea7d
Added optimization for sending ACKs immediately. Turned optimizations on. Increased listening time to 1/64 s again due to problems with broadcasts with the 1/128 s setting
2009-04-06 22:50:35 +00:00
nifi
9f2ff48fda
added 802.15.4 frame packeter
2009-04-06 13:19:03 +00:00
adamdunkels
ed1e945e66
Added guard code so that OFF_TIME is never zero
2009-04-03 20:08:05 +00:00
adamdunkels
8dbd2b2337
Significant power consumption optimization: LPP now keeps track of encounters with neighbors and uses this information to keep the radio switched off longer.
2009-04-03 19:59:22 +00:00
adamdunkels
1d86b01bfb
Made optimizations explicit (and configurable). Added missing initialization of dutycycle protothread. Reduced default listen time and off time.
2009-04-03 11:45:06 +00:00
adamdunkels
04101aae36
Fixed alignment problem on the MSP430, where the LPP header may be misaligned
2009-03-31 17:39:54 +00:00
nvt-se
e2cc8b2a3e
send all queued packet once we have the chance.
2009-03-31 14:44:13 +00:00
nvt-se
1d47e2a8da
send immediate probes only if the packet is directed to us.
...
sleep for OFF_TIME if the queue is empty.
restrict double packet lifetime timeouts to unicast packets.
stop ctimer in remove_queued_packet in case the function is not called
via the ctimer callback. it could overwrite a valid packet otherwise.
2009-03-31 14:11:25 +00:00
nvt-se
dd082f7fcf
improvements to lpp based on code from Adam and discussions with Thiemo.
...
* queue multiple packets
* send a strobe back immediately after receiving a data packet
* double the packet lifetime to allow for a missed probe
2009-03-31 12:47:00 +00:00
nvt-se
d8caaca289
listen time and off time parameters configurable from outside because cc1020 needs longer listen time.
2009-03-26 12:50:57 +00:00
adamdunkels
ec1677ca6c
Added a function (quick hack) that sets the radio transmission power of outgoing announcement packets in xmac
2009-03-23 21:06:26 +00:00
adamdunkels
1cbc0f4ea9
Send announcement packets only if there are any announcements to send
2009-03-23 21:00:25 +00:00
adamdunkels
65eb5fd4e8
Renamed the rimebuf module to packetbuf to signal that the module is used outside of a pure Rime context (e.g., the sicslowpan code uses it).
2009-03-12 21:58:20 +00:00
adamdunkels
dc7491f810
Bugfix and optimization: X-MAC did not properly switch the radio off after sending a packet, resulting in increased power consumption. For packets that require an ACK, we can let the radio be on in anticipation of the ACK (controlled with an WITH_ACK_OPTIMIZATION option)
2009-03-05 19:37:52 +00:00
adamdunkels
d813d343c5
Cleaned up old left-over code
2009-03-01 20:38:57 +00:00
adamdunkels
7010eb84b8
Added support for communication power accounting. Energy is attributed to idle listening when the radio is switched off. Enegrgy is attributed to an incoming packet when it is received. Energy is attributed to an outgoing packet when it is transmitted.
2009-03-01 20:37:16 +00:00
adamdunkels
e6907a1d8b
Include random.h
2009-02-20 21:22:39 +00:00
adamdunkels
aaa8c9d2c9
Construct the X-MAC header on the stack instead of directly in the packet header, because the packet header may be misaligned. A bit of cleanup in the code too.
2009-02-15 22:05:06 +00:00
adamdunkels
e4b1ff461e
Added MAC-layer announcement beacons to X-MAC. Configuratble through XMAC_CONF_ANNOUNCEMENTS
2009-02-14 20:35:03 +00:00
adamdunkels
585620c102
Reverted the recent change from random_rand() to rand(). It turned out that
...
since libc rand() returns a signed int, there were frequently problems with
timer values wrapping. By reverting to random_rand(), we can provide a
random generator that returns an unsigned and the timer problems are solved.
2009-02-11 11:08:53 +00:00
