Commit graph

12 commits

Author SHA1 Message Date
Michael LeMay 58a00b7c23 x86, galileo: Add driver for Isolated Memory Regions (IMRs)
The Intel Quark X1000 SoC includes support for Isolated Memory Regions
(IMRs), which are specified using range registers and associated
control registers that are accessible via the message bus.  This patch
adds a driver for accessing those registers.
2016-03-17 08:35:49 -07:00
Michael LeMay 25c07613c2 x86: Add driver for message bus
The Intel Quark X1000 SoC includes a message bus that is accessible
via PCI configuration registers.  It communicates to various SoC
components such as the Isolated Memory Region (IMR) registers and the
Remote Management Unit.  This patch adds a driver for accessing the
message bus.
2016-03-17 08:35:48 -07:00
Michael LeMay 58874ea25d x86, galileo: Refactor I2C and GPIO initialization
This patch revises the I2C and GPIO initialization code to always be
run during platform boot rather than within each process that requires
it.

This patch also revises the gpio-output example to use a pin that is
set as an output by the default pinmux configuration.  Previously, it
used a pin that was set as an output by the pinmux configuration that
is in effect when the OS does not change the pinmux configuration.
2016-02-16 21:19:44 -08:00
Michael LeMay c815fa4511 x86: Use shared ISR for I2C and GPIO
This patch permits interrupts to be generated by both the I2C and GPIO
controllers for simultaneously-executing applications. The controllers
share a single interrupt pin, INTC. Prior to this patch,
quarkX1000_gpio_init() routed INTA to PIRQC and IRQ 10 (due to an
incorrect assumption that INTA is connected to the GPIO controller),
and quarkX1000_i2c_init() routed INTC to PIRQC and IRQ 9. The I2C
controller initialization is a prerequisite for GPIO initialization,
so the final configuration was that INTA and INTC were both routed to
PIRQC and IRQ 10. Thus, only the GPIO ISR was being invoked, even if
the I2C controller was actually responsible for the interrupt.

This patch refactors the I2C and GPIO ISR setup and handler code so
that the shared portions are combined in
cpu/x86/drivers/legacy_pc/shared-isr.[ch].  The I2C and GPIO drivers
communicate their interrupt information to the shared component by
placing structures in a specific section of the binary.
2016-02-16 21:19:44 -08:00
Michael LeMay e297177a69 x86: Streamline MMIO accesses in GPIO and I2C drivers
This patch refactors the MMIO routines in the GPIO and I2C drivers to
eliminate the base_addr parameter that specifies the MMIO base
address.  Instead, just the MMIO routines themselves retrieve the base
address from the driver structure.
2015-12-21 08:06:14 -02:00
Michael LeMay abeed93da5 x86: Add driver for Intel Quark X1000 built-in Ethernet
This patch adds a simple, space-efficient driver for the Ethernet
interface built into the Intel Quark X1000.  It only allocates a
single packet descriptor for each of the transmit and receive
directions, computes checksums on the CPU, and enables
store-and-forward mode for both transmit and receive directions.
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga 4726bc3313 x86: Add Intel Quark X1000 GPIO Controller (non-legacy) interrupt support
Since Galileo pinmux is available, this patch adds interrupt support
for GPIO Controller (non-legacy).
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga 495dcd659a x86: Add PCAL9535A support
This patch adds gpio-pcal9535a.c and gpio-pcal9535a.h files,
which support access to I2C-based PCAL9535A GPIO controller
configuration register through a function interface.

The PCAL9535A is a low-voltage 16-bit GPIO expander with interrupt
and reset for I2C-bus/SMBus applications. It contains the PCA9535
register set of four pairs of 8-bit Configuration, Input, Output,
and Polarity Inversion registers, and additionally, the PCAL9535A has
Agile I/O, which are additional features specifically designed to
enhance the I/O. More about PCAL9535A can be found in its datasheet[1].

This driver is needed in order to configure Galileo pinmux.

[1] - http://www.nxp.com/documents/data_sheet/PCAL9535A.pdf
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga a27af5b395 x86: Add Intel Quark X1000 I2C support
This patch adds the i2c.c, i2c.h and i2c-registers.h files,
which support access to I2C controller configuration register
through a function interface.
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga 2d552285cd x86: Add Intel Quark X1000 GPIO Controller (non-legacy) support
This patch adds the gpio.c and gpio.h files, which support
access to GPIO Controller (non-legacy) configuration register
through a function interface.

It doesn't add interrupt support due to pinmux reasons. On
Galileo Gen 2 we need to configure a pin as input/interrupt
using pinmux and this can only be achieved through I2C. There's
one pin exported by default as GPIO output and we used this one
to test this driver.

In the future, we plan to add an I2C driver and a pinmux configuration
driver in order to solve this kind of problems.
2015-12-21 08:06:14 -02:00
Ricardo de Almeida Gonzaga 60f6edef80 x86: Add support for PCI BAR1
This patch adds support for PCI BAR1 and also changes
the pci_init(), instead of having one function for each `bar`
we now set the `bar` to pci_config_addr_t parameter before calling
the pci_init() function..
2015-12-21 08:06:14 -02:00
Michael LeMay 15f947fe40 x86: Add Intel Quark X1000 UART support.
This patch adds a driver that wraps the generic 16X50 UART driver with
specific support for the two Intel Quark X1000 built-in UARTs.
2015-12-21 08:06:14 -02:00