diff --git a/examples/osd/arduino-relaybox/Makefile b/examples/osd/arduino-relaybox/Makefile new file mode 100644 index 000000000..5a017eac0 --- /dev/null +++ b/examples/osd/arduino-relaybox/Makefile @@ -0,0 +1,70 @@ +# Set this to the name of your sketch (without extension .pde) +SKETCH=sketch +EXE=arduino-example + +all: $(EXE) + +CONTIKI=../../.. + +# Contiki IPv6 configuration +CONTIKI_WITH_IPV6 = 1 + +CFLAGS += -DPROJECT_CONF_H=\"project-conf.h\" + +PROJECT_SOURCEFILES += ${SKETCH}.cpp + +# automatically build RESTful resources +REST_RESOURCES_DIR = ./resources +REST_RESOURCES_DIR_COMMON = ../resources-common +REST_RESOURCES_FILES= $(notdir \ + $(shell find $(REST_RESOURCES_DIR) -name '*.c') \ + $(shell find $(REST_RESOURCES_DIR_COMMON) -name '*.c') \ + ) + +PROJECTDIRS += $(REST_RESOURCES_DIR) $(REST_RESOURCES_DIR_COMMON) +PROJECT_SOURCEFILES += $(REST_RESOURCES_FILES) + +# variable for Makefile.include +ifneq ($(TARGET), minimal-net) +CFLAGS += -DUIP_CONF_IPV6_RPL=1 +else +# minimal-net does not support RPL under Linux and is mostly used to test CoAP only +${info INFO: compiling without RPL} +CFLAGS += -DUIP_CONF_IPV6_RPL=0 +CFLAGS += -DHARD_CODED_ADDRESS=\"fdfd::10\" +${info INFO: compiling with large buffers} +CFLAGS += -DUIP_CONF_BUFFER_SIZE=2048 +CFLAGS += -DREST_MAX_CHUNK_SIZE=1024 +CFLAGS += -DCOAP_MAX_HEADER_SIZE=640 +endif + +# linker optimizations +SMALL=1 + + +# REST Engine shall use Erbium CoAP implementation +APPS += er-coap +APPS += rest-engine +APPS += arduino + +include $(CONTIKI)/Makefile.include +include $(CONTIKI)/apps/arduino/Makefile.include + +$(CONTIKI)/tools/tunslip6: $(CONTIKI)/tools/tunslip6.c + (cd $(CONTIKI)/tools && $(MAKE) tunslip6) + +connect-router: $(CONTIKI)/tools/tunslip6 + sudo $(CONTIKI)/tools/tunslip6 aaaa::1/64 + +connect-router-cooja: $(CONTIKI)/tools/tunslip6 + sudo $(CONTIKI)/tools/tunslip6 -a 127.0.0.1 aaaa::1/64 + +connect-minimal: + sudo ip address add fdfd::1/64 dev tap0 + +avr-size: $(EXE).$(TARGET).sz + +flash: $(EXE).$(TARGET).u $(EXE).$(TARGET).eu + +.PHONY: flash avr-size +.PRECIOUS: $(EXE).$(TARGET).hex $(EXE).$(TARGET).eep diff --git a/examples/osd/arduino-relaybox/README.md b/examples/osd/arduino-relaybox/README.md new file mode 100644 index 000000000..e1490ed05 --- /dev/null +++ b/examples/osd/arduino-relaybox/README.md @@ -0,0 +1,11 @@ +Arduino compatibility example +============================= + +This example shows that it is now possible to re-use arduino sketches in +Contiki. This example documents the necessary magic. Arduino specifies +two routines, `setup` and `loop`. Before `setup` is called, the +framework initializes hardware. In original Arduino, all this is done in +a `main` function (in C). For contiki we define a process that does the +same. + +See the documentation file in apps/contiki-compat/README.md diff --git a/examples/osd/arduino-relaybox/arduino-example.c b/examples/osd/arduino-relaybox/arduino-example.c new file mode 100644 index 000000000..ea74dd8b8 --- /dev/null +++ b/examples/osd/arduino-relaybox/arduino-example.c @@ -0,0 +1,2 @@ +#include +AUTOSTART_PROCESSES(&arduino_sketch); diff --git a/examples/osd/arduino-relaybox/flash.sh b/examples/osd/arduino-relaybox/flash.sh new file mode 100755 index 000000000..e82962073 --- /dev/null +++ b/examples/osd/arduino-relaybox/flash.sh @@ -0,0 +1,2 @@ +#!/bin/bash +make TARGET=osd-merkur-128 flash diff --git a/examples/osd/arduino-relaybox/project-conf.h b/examples/osd/arduino-relaybox/project-conf.h new file mode 100644 index 000000000..3d06ae843 --- /dev/null +++ b/examples/osd/arduino-relaybox/project-conf.h @@ -0,0 +1,99 @@ +/* + * Copyright (c) 2010, Swedish Institute of Computer Science. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * + */ + +#ifndef PROJECT_RPL_WEB_CONF_H_ +#define PROJECT_RPL_WEB_CONF_H_ + +#define PLATFORM_HAS_LEDS 1 +//#define PLATFORM_HAS_BUTTON 1 +#define PLATFORM_HAS_BATTERY 1 + +/* For Debug: Dont allow MCU sleeping between channel checks */ +//#undef RDC_CONF_MCU_SLEEP +//#define RDC_CONF_MCU_SLEEP 0 + +/* Disabling RDC for demo purposes. Core updates often require more memory. */ +/* For projects, optimize memory and enable RDC again. */ +//#undef NETSTACK_CONF_RDC +//#define NETSTACK_CONF_RDC nullrdc_driver +//#undef NETSTACK_CONF_MAC +//#define NETSTACK_CONF_MAC nullmac_driver + +/* Increase rpl-border-router IP-buffer when using more than 64. */ +//#undef REST_MAX_CHUNK_SIZE +//#define REST_MAX_CHUNK_SIZE 64 + +/* Estimate your header size, especially when using Proxy-Uri. */ +/* +#undef COAP_MAX_HEADER_SIZE +#define COAP_MAX_HEADER_SIZE 70 +*/ + +/* The IP buffer size must fit all other hops, in particular the border router. */ + +#undef UIP_CONF_BUFFER_SIZE +#define UIP_CONF_BUFFER_SIZE 256 + + +/* Multiplies with chunk size, be aware of memory constraints. */ +#undef COAP_MAX_OPEN_TRANSACTIONS +#define COAP_MAX_OPEN_TRANSACTIONS 4 + +/* Must be <= open transaction number, default is COAP_MAX_OPEN_TRANSACTIONS-1. */ +/* +#undef COAP_MAX_OBSERVERS +#define COAP_MAX_OBSERVERS 2 +*/ + +/* Filtering .well-known/core per query can be disabled to save space. */ +/* +#undef COAP_LINK_FORMAT_FILTERING +#define COAP_LINK_FORMAT_FILTERING 0 +*/ + +/* +#undef LLSEC802154_CONF_ENABLED +#define LLSEC802154_CONF_ENABLED 1 +#undef NETSTACK_CONF_FRAMER +#define NETSTACK_CONF_FRAMER noncoresec_framer +#undef NETSTACK_CONF_LLSEC +#define NETSTACK_CONF_LLSEC noncoresec_driver +#undef NONCORESEC_CONF_SEC_LVL +#define NONCORESEC_CONF_SEC_LVL 1 + +#define NONCORESEC_CONF_KEY { 0x00 , 0x01 , 0x02 , 0x03 , \ + 0x04 , 0x05 , 0x06 , 0x07 , \ + 0x08 , 0x09 , 0x0A , 0x0B , \ + 0x0C , 0x0D , 0x0E , 0x0F } + +*/ + +#endif /* PROJECT_RPL_WEB_CONF_H_ */ diff --git a/examples/osd/arduino-relaybox/resources/res-led.c b/examples/osd/arduino-relaybox/resources/res-led.c new file mode 100644 index 000000000..fb0fa138f --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-led.c @@ -0,0 +1,104 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_led, + "title=\"LED: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +extern uint8_t led_pin; +extern uint8_t led_status; + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", led_status); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", led_status); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + digitalWrite(led_pin, LOW); + led_status=1; + } else if(strncmp(mode, "off", len) == 0) { + digitalWrite(led_pin, HIGH); + led_status=0; + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay1.c b/examples/osd/arduino-relaybox/resources/res-relay1.c new file mode 100644 index 000000000..b3dc25823 --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay1.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay1, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_1)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_1)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_1,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_1,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay2.c b/examples/osd/arduino-relaybox/resources/res-relay2.c new file mode 100644 index 000000000..a97d44c6c --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay2.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay2, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_2)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_2)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_2,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_2,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay3.c b/examples/osd/arduino-relaybox/resources/res-relay3.c new file mode 100644 index 000000000..cc7fe3f2d --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay3.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay3, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_3)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_3)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_3,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_3,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay4.c b/examples/osd/arduino-relaybox/resources/res-relay4.c new file mode 100644 index 000000000..1bab3e999 --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay4.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay4, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_4)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_4)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_4,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_4,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay5.c b/examples/osd/arduino-relaybox/resources/res-relay5.c new file mode 100644 index 000000000..27846df05 --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay5.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay5, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_5)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_5)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_5,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_5,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay6.c b/examples/osd/arduino-relaybox/resources/res-relay6.c new file mode 100644 index 000000000..fd28d90f1 --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay6.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay6, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_6)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_6)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_6,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_6,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay7.c b/examples/osd/arduino-relaybox/resources/res-relay7.c new file mode 100644 index 000000000..29de8a857 --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay7.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay7, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_7)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_7)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_7,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_7,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/resources/res-relay8.c b/examples/osd/arduino-relaybox/resources/res-relay8.c new file mode 100644 index 000000000..3f83675d6 --- /dev/null +++ b/examples/osd/arduino-relaybox/resources/res-relay8.c @@ -0,0 +1,100 @@ +/* + * Copyright (c) 2013, Institute for Pervasive Computing, ETH Zurich + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Institute nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * This file is part of the Contiki operating system. + */ + +/** + * \file + * Door resource + * \author + * Harald Pichler + */ + +#include "contiki.h" + +#include +#include "rest-engine.h" +#include "Arduino.h" +#include "dev/relay-sensor.h" + +static void res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); +static void res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset); + +/* A simple getter example. Returns the reading from the sensor with a simple etag */ +RESOURCE(res_relay8, + "title=\"Relay: , POST/PUT mode=on|off\";rt=\"Control\"", + res_get_handler, + res_post_put_handler, + res_post_put_handler, + NULL); + +static void +res_get_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + unsigned int accept = -1; + REST.get_header_accept(request, &accept); + + if(accept == -1 || accept == REST.type.TEXT_PLAIN) { + REST.set_header_content_type(response, REST.type.TEXT_PLAIN); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "%d", relay_sensor.value(RELAY_SENSOR_8)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else if(accept == REST.type.APPLICATION_JSON) { + REST.set_header_content_type(response, REST.type.APPLICATION_JSON); + snprintf((char *)buffer, REST_MAX_CHUNK_SIZE, "{'led':%d}", relay_sensor.value(RELAY_SENSOR_8)); + + REST.set_response_payload(response, buffer, strlen((char *)buffer)); + } else { + REST.set_response_status(response, REST.status.NOT_ACCEPTABLE); + const char *msg = "Supporting content-types text/plain and application/json"; + REST.set_response_payload(response, msg, strlen(msg)); + } +} + +static void +res_post_put_handler(void *request, void *response, uint8_t *buffer, uint16_t preferred_size, int32_t *offset) +{ + size_t len = 0; + const char *mode = NULL; + int success = 1; + + if(success && (len = REST.get_post_variable(request, "mode", &mode))) { + if(strncmp(mode, "on", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_8,1); + } else if(strncmp(mode, "off", len) == 0) { + relay_sensor.configure(RELAY_SENSOR_8,0); + } else { + success = 0; + } + } else { + success = 0; + } if(!success) { + REST.set_response_status(response, REST.status.BAD_REQUEST); + } +} diff --git a/examples/osd/arduino-relaybox/run.sh b/examples/osd/arduino-relaybox/run.sh new file mode 100755 index 000000000..5d5cbbbb4 --- /dev/null +++ b/examples/osd/arduino-relaybox/run.sh @@ -0,0 +1,5 @@ +#!/bin/bash +# For the ages-old bootloader (before 2014) you want to use +# BOOTLOADER_GET_MAC=0x0001f3a0 as parameter to make below. +make clean TARGET=osd-merkur-128 +make TARGET=osd-merkur-128 diff --git a/examples/osd/arduino-relaybox/sketch.pde b/examples/osd/arduino-relaybox/sketch.pde new file mode 100644 index 000000000..d90e0ac6a --- /dev/null +++ b/examples/osd/arduino-relaybox/sketch.pde @@ -0,0 +1,57 @@ +/* + * Sample arduino sketch using contiki features. + * We turn the LED off + * We allow read the moisture sensor + * Unfortunately sleeping for long times in loop() isn't currently + * possible, something turns off the CPU (including PWM outputs) if a + * Proto-Thread is taking too long. We need to find out how to sleep in + * a Contiki-compatible way. + * Note that for a normal arduino sketch you won't have to include any + * of the contiki-specific files here, the sketch should just work. + */ + +extern "C" { +#include "arduino-process.h" +#include "rest-engine.h" +#include "net/netstack.h" +#include "dev/relay-sensor.h" + +extern resource_t res_led, res_battery, res_cputemp, + res_relay1, res_relay2, res_relay3, res_relay4, + res_relay5, res_relay6, res_relay7, res_relay8; + +uint8_t led_pin=4; +uint8_t led_status; + +} + +void setup (void) +{ + // switch off the led + pinMode(led_pin, OUTPUT); + digitalWrite(led_pin, HIGH); + led_status=0; + // init relay + SENSORS_ACTIVATE(relay_sensor); + // init coap resourcen + rest_init_engine (); + #pragma GCC diagnostic ignored "-Wwrite-strings" + rest_activate_resource (&res_led, "s/led"); + rest_activate_resource (&res_battery, "s/battery"); + rest_activate_resource (&res_cputemp, "s/cputemp"); + rest_activate_resource (&res_relay1, "relay/1"); + rest_activate_resource (&res_relay2, "relay/2"); + rest_activate_resource (&res_relay3, "relay/3"); + rest_activate_resource (&res_relay4, "relay/4"); + rest_activate_resource (&res_relay5, "relay/5"); + rest_activate_resource (&res_relay6, "relay/6"); + rest_activate_resource (&res_relay7, "relay/7"); + rest_activate_resource (&res_relay8, "relay/8"); + #pragma GCC diagnostic pop + NETSTACK_MAC.off(1); +} + +void loop (void) +{ + +}