initial upload

examples/osd/arduino-wateralert/Makefile

@@ -0,0 +1,102 @@
+# Set this to the name of your sketch (without extension .pde)
+SKETCH=sketch
+
+all: arduino-example \
+     arduino-example.osd-merkur.hex arduino-example.osd-merkur.eep
+
+# variable for this Makefile
+# configure CoAP implementation (3|7|12|13) (er-coap-07 also supports CoAP draft 08)
+WITH_COAP=13
+
+# for some platforms
+UIP_CONF_IPV6=1
+# IPv6 make config disappeared completely
+CFLAGS += -DUIP_CONF_IPV6=1
+
+CONTIKI=../../..
+CFLAGS += -DPROJECT_CONF_H=\"project-conf.h\"
+
+PROJECT_SOURCEFILES += resource_water.c ${SKETCH}.cpp
+
+# variable for Makefile.include
+ifneq ($(TARGET), minimal-net)
+CFLAGS += -DUIP_CONF_IPV6_RPL=1
+else
+# minimal-net does not support RPL under Linux and is mostly used to test CoAP only
+${info INFO: compiling without RPL}
+CFLAGS += -DUIP_CONF_IPV6_RPL=0
+CFLAGS += -DHARD_CODED_ADDRESS=\"fdfd::10\"
+${info INFO: compiling with large buffers}
+CFLAGS += -DUIP_CONF_BUFFER_SIZE=2048
+CFLAGS += -DREST_MAX_CHUNK_SIZE=1024
+CFLAGS += -DCOAP_MAX_HEADER_SIZE=640
+endif
+
+# linker optimizations
+SMALL=1
+
+# REST framework, requires WITH_COAP
+ifeq ($(WITH_COAP), 13)
+${info INFO: compiling with CoAP-13}
+CFLAGS += -DWITH_COAP=13
+CFLAGS += -DREST=coap_rest_implementation
+CFLAGS += -DUIP_CONF_TCP=0
+APPS += er-coap-13
+else ifeq ($(WITH_COAP), 12)
+${info INFO: compiling with CoAP-12}
+CFLAGS += -DWITH_COAP=12
+CFLAGS += -DREST=coap_rest_implementation
+CFLAGS += -DUIP_CONF_TCP=0
+APPS += er-coap-12
+else ifeq ($(WITH_COAP), 7)
+${info INFO: compiling with CoAP-08}
+CFLAGS += -DWITH_COAP=7
+CFLAGS += -DREST=coap_rest_implementation
+CFLAGS += -DUIP_CONF_TCP=0
+APPS += er-coap-07
+else ifeq ($(WITH_COAP), 3)
+${info INFO: compiling with CoAP-03}
+CFLAGS += -DWITH_COAP=3
+CFLAGS += -DREST=coap_rest_implementation
+CFLAGS += -DUIP_CONF_TCP=0
+APPS += er-coap-03
+else
+${info INFO: compiling with HTTP}
+CFLAGS += -DWITH_HTTP
+CFLAGS += -DREST=http_rest_implementation
+CFLAGS += -DUIP_CONF_TCP=1
+APPS += er-http-engine
+endif
+
+APPS += erbium time json arduino json-resource
+
+include $(CONTIKI)/Makefile.include
+include $(CONTIKI)/apps/arduino/Makefile.include
+
+arduino-example.osd-merkur.hex: arduino-example.osd-merkur
+	avr-objcopy -j .text -j .data -O ihex arduino-example.osd-merkur \
+	    arduino-example.osd-merkur.hex
+
+arduino-example.osd-merkur.eep: arduino-example.osd-merkur
+	avr-objcopy -j .eeprom --set-section-flags=.eeprom="alloc,load" \
+	    --change-section-lma .eeprom=0 -O ihex                      \
+	    arduino-example.osd-merkur arduino-example.osd-merkur.eep
+
+flash: arduino-example.osd-merkur.hex arduino-example.osd-merkur.eep
+	avrdude -pm128rfa1 -c arduino -P/dev/ttyUSB0 -b57600 -e -U \
+	    flash:w:arduino-example.osd-merkur.hex:a -U \
+	    eeprom:w:arduino-example.osd-merkur.eep:a
+
+.PHONY: flash
+
+$(CONTIKI)/tools/tunslip6:      $(CONTIKI)/tools/tunslip6.c
+	(cd $(CONTIKI)/tools && $(MAKE) tunslip6)
+
+connect-router: $(CONTIKI)/tools/tunslip6
+	sudo $(CONTIKI)/tools/tunslip6 aaaa::1/64
+
+connect-router-cooja:   $(CONTIKI)/tools/tunslip6
+	sudo $(CONTIKI)/tools/tunslip6 -a 127.0.0.1 aaaa::1/64
+
+connect-minimal:
+	sudo ip address add fdfd::1/64 dev tap0

examples/osd/arduino-wateralert/README.md

@@ -0,0 +1,11 @@
+Arduino compatibility example
+=============================
+
+This example shows that it is now possible to re-use arduino sketches in
+Contiki. This example documents the necessary magic. Arduino specifies
+two routines, `setup` and `loop`. Before `setup` is called, the
+framework initializes hardware. In original Arduino, all this is done in
+a `main` function (in C). For contiki we define a process that does the
+same.
+
+See the documentation file in apps/contiki-compat/README.md

examples/osd/arduino-wateralert/arduino-example.c

@@ -0,0 +1,2 @@
+#include <arduino-process.h>
+AUTOSTART_PROCESSES(&arduino_sketch);

examples/osd/arduino-wateralert/flash.sh

@@ -0,0 +1,2 @@
+#!/bin/bash
+make TARGET=osd-merkur flash

examples/osd/arduino-wateralert/project-conf.h

@@ -0,0 +1,101 @@
+/*
+ * Copyright (c) 2010, Swedish Institute of Computer Science.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in the
+ *    documentation and/or other materials provided with the distribution.
+ * 3. Neither the name of the Institute nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED.  IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ *
+ *
+ */
+
+#ifndef PROJECT_RPL_WEB_CONF_H_
+#define PROJECT_RPL_WEB_CONF_H_
+
+#define PLATFORM_HAS_LEDS    1
+//#define PLATFORM_HAS_BUTTON  1
+#define PLATFORM_HAS_BATTERY 1
+
+#define SICSLOWPAN_CONF_FRAG	1
+
+/* For Debug: Dont allow MCU sleeping between channel checks */
+//#undef RDC_CONF_MCU_SLEEP
+//#define RDC_CONF_MCU_SLEEP       0
+
+/* Disabling RDC for demo purposes. Core updates often require more memory. */
+/* For projects, optimize memory and enable RDC again. */
+// #undef NETSTACK_CONF_RDC
+//#define NETSTACK_CONF_RDC     nullrdc_driver
+
+/* Increase rpl-border-router IP-buffer when using more than 64. */
+#undef REST_MAX_CHUNK_SIZE
+#define REST_MAX_CHUNK_SIZE    64
+
+/* Estimate your header size, especially when using Proxy-Uri. */
+/*
+#undef COAP_MAX_HEADER_SIZE
+#define COAP_MAX_HEADER_SIZE    70
+*/
+
+/* The IP buffer size must fit all other hops, in particular the border router. */
+
+#undef UIP_CONF_BUFFER_SIZE
+#define UIP_CONF_BUFFER_SIZE    256
+
+
+/* Multiplies with chunk size, be aware of memory constraints. */
+#undef COAP_MAX_OPEN_TRANSACTIONS
+#define COAP_MAX_OPEN_TRANSACTIONS   4
+
+/* Must be <= open transaction number, default is COAP_MAX_OPEN_TRANSACTIONS-1. */
+/*
+#undef COAP_MAX_OBSERVERS
+#define COAP_MAX_OBSERVERS      2
+*/
+
+/* Filtering .well-known/core per query can be disabled to save space. */
+/*
+#undef COAP_LINK_FORMAT_FILTERING
+#define COAP_LINK_FORMAT_FILTERING      0
+*/
+
+/* Save some memory for the sky platform. */
+/*
+#undef NBR_TABLE_CONF_MAX_NEIGHBORS
+#define NBR_TABLE_CONF_MAX_NEIGHBORS     10
+#undef UIP_CONF_MAX_ROUTES
+#define UIP_CONF_MAX_ROUTES   10
+*/
+
+/* Reduce 802.15.4 frame queue to save RAM. */
+/*
+#undef QUEUEBUF_CONF_NUM
+#define QUEUEBUF_CONF_NUM       4
+*/
+
+/*
+#undef SICSLOWPAN_CONF_FRAG
+#define SICSLOWPAN_CONF_FRAG	1
+*/
+
+#endif /* PROJECT_RPL_WEB_CONF_H_ */

examples/osd/arduino-wateralert/resource_water.c

@@ -0,0 +1,42 @@
+/**
+ * \file
+ *      Resource for Arduino analog read
+ * \author
+ *      Harald Pichler <harald@the-develop.net>
+ *
+ * \brief get/put pwm and period for LED pin
+ *
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include "contiki.h"
+#include "jsonparse.h"
+/* Only coap 13 for now */
+#include "er-coap-13.h"
+#include "generic_resource.h"
+#include "resource_water.h"
+#include "Arduino.h"
+
+size_t
+water_v (const char *name, uint8_t is_json, char *buf, size_t bufsize)
+{
+  water_voltage = analogRead(water_pin);            
+  return snprintf
+    (buf, bufsize, "%d", water_voltage);
+}
+
+GENERIC_RESOURCE \
+    ( water, METHOD_GET
+    , "water/v"
+    , Moisture voltage
+    , V
+    , NULL
+    , water_v
+    );
+
+/*
+ * VI settings, see coding style
+ * ex:ts=8:et:sw=2
+ */

examples/osd/arduino-wateralert/resource_water.h

@@ -0,0 +1,30 @@
+/**
+ * \defgroup Arduino LED PWM example
+ *
+ * Resource definition for Arduino LED PWM module
+ *
+ * @{
+ */
+
+/**
+ * \file
+ *         Resource definitions for the Arduino LED PWM module
+ *      
+ * \author
+ *         Ralf Schlatterbeck <rsc@tux.runtux.com>
+ */
+
+#ifndef water_h
+#define water_h
+#include "contiki.h"
+#include "contiki-net.h"
+#include "erbium.h"
+#include "er-coap-13.h"
+
+extern uint8_t water_pin;
+extern uint16_t water_voltage;
+
+extern resource_t resource_water;
+
+#endif // water_h
+/** @} */

examples/osd/arduino-wateralert/run.sh

@@ -0,0 +1,5 @@
+#!/bin/bash
+# For the new bootloader (using a jump-table) you want to use
+# BOOTLOADER_GET_MAC=0x0001ff80 (which is the current default)
+make clean TARGET=osd-merkur
+make TARGET=osd-merkur BOOTLOADER_GET_MAC=0x0001f3a0

examples/osd/arduino-wateralert/sketch.pde

@@ -0,0 +1,34 @@
+/*
+ * Sample arduino sketch using contiki features.
+ * We turn the LED off 
+ * We allow read the water sensor
+ * Unfortunately sleeping for long times in loop() isn't currently
+ * possible, something turns off the CPU (including PWM outputs) if a
+ * Proto-Thread is taking too long. We need to find out how to sleep in
+ * a Contiki-compatible way.
+ * Note that for a normal arduino sketch you won't have to include any
+ * of the contiki-specific files here, the sketch should just work.
+ */
+
+extern "C" {
+#include <stdio.h>
+#include "resource_water.h"
+
+#define LED_PIN 4
+
+uint8_t water_pin = A5;
+uint16_t water_voltage = 0;
+}
+
+void setup (void)
+{
+    pinMode(LED_PIN, OUTPUT);
+    digitalWrite(LED_PIN, HIGH);
+    rest_init_engine ();
+    rest_activate_resource (&resource_water);
+}
+
+void loop (void)
+{
+
+}