blink blue but with the timer.

This commit is contained in:
Mariano Alvira 2009-04-20 14:15:24 -04:00
parent b508d138a8
commit d25385d2aa
2 changed files with 93 additions and 1 deletions

View file

@ -74,7 +74,7 @@ tests/rftest-tx.obj: src/maca.o src/nvm.o
$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
%.dis: %.obj
$(OBJDUMP) -D $< > $@
$(OBJDUMP) -SD $< > $@
%.obj: $(LDSCRIPT) %.o
$(LD) $(LDFLAGS) $(AOBJS) \

92
tests/tmr.c Normal file
View file

@ -0,0 +1,92 @@
/* Timer registers are all 16-bit wide with 16-bit access only */
#define TMR_OFFSET (0x20)
#define TMR_BASE (0x80007000)
#define TMR0_BASE (TMR_BASE)
#define TMR1_BASE (TMR_BASE + TMR_OFFSET*1)
#define TMR2_BASE (TMR_BASE + TMR_OFFSET*2)
#define TMR3_BASE (TMR_BASE + TMR_OFFSET*3)
#define TMR_REGOFF_COMP1 (0x0)
#define TMR_REGOFF_COMP2 (0x2)
#define TMR_REGOFF_CAPT (0x4)
#define TMR_REGOFF_LOAD (0x6)
#define TMR_REGOFF_HOLD (0x8)
#define TMR_REGOFF_CNTR (0xa)
#define TMR_REGOFF_CTRL (0xc)
#define TMR_REGOFF_SCTRL (0xe)
#define TMR_REGOFF_CMPLD1 (0x10)
#define TMR_REGOFF_CMPLD2 (0x12)
#define TMR_REGOFF_CSCTRL (0x14)
#define TMR_REGOFF_ENBL (0x1e)
/* Timer 0 registers */
#define TMR0_COMP1 (TMR0_BASE + TMR_REGOFF_COMP1)
#define TMR0_COMP_UP TMR0_COMP1
#define TMR0_COMP2 (TMR0_BASE + TMR_REGOFF_COMP2)
#define TMR0_COMP_DOWN TMR0_COMP2
#define TMR0_CAPT (TMR0_BASE + TMR_REGOFF_CAPT)
#define TMR0_LOAD (TMR0_BASE + TMR_REGOFF_LOAD)
#define TMR0_HOLD (TMR0_BASE + TMR_REGOFF_HOLD)
#define TMR0_CNTR (TMR0_BASE + TMR_REGOFF_CTRL)
#define TMR0_CTRL (TMR0_BASE + TMR_REGOFF_CTRL)
#define TMR0_SCTRL (TMR0_BASE + TMR_REGOFF_SCTRL)
#define TMR0_CMPLD1 (TMR0_BASE + TMR_REGOFF_CMPLD1)
#define TMR0_CMPLD2 (TMR0_BASE + TMR_REGOFF_CMPLD2)
#define TMR0_CSCTRL (TMR0_BASE + TMR_REGOFF_CSCTRL)
/* one enable register to rule them all */
#define TMR_ENBL TMR0_BASE + TMR_REGOFF_ENBL
#define MBAR_GPIO 0x80000000
#define GPIO_PAD_DIR0 0x80000000
#define GPIO_DATA0 0x80000008
#define UART1_DATA 0x80005008
#define DELAY 400000
#define reg32(x) (*(volatile uint32_t *)(x))
#define reg16(x) (*(volatile uint16_t *)(x))
#include "embedded_types.h"
__attribute__ ((section ("startup")))
void main(void) {
/* pin direction */
reg32(GPIO_PAD_DIR0) = 0x00000400;
/* timer setup */
/* CTRL */
#define COUNT_MODE 1 /* use rising edge of primary source */
#define PRIME_SRC 0xf /* Perip. clock with 128 prescale (for 24Mhz = 187500Hz)*/
#define SEC_SRC 0 /* don't need this */
#define ONCE 0 /* keep counting */
#define LEN 1 /* count until compare then reload with value in LOAD */
#define DIR 0 /* count up */
#define CO_INIT 0 /* other counters cannot force a re-initialization of this counter */
#define OUT_MODE 0 /* OFLAG is asserted while counter is active */
reg16(TMR_ENBL) = 0; /* tmrs reset to enabled */
reg16(TMR0_SCTRL) = 0;
reg16(TMR0_LOAD) = 0; /* reload to zero */
reg16(TMR0_COMP_UP) = 18750; /* trigger a reload at the end */
reg16(TMR0_CMPLD1) = 18750; /* compare 1 triggered reload level, 10HZ maybe? */
reg16(TMR0_CNTR) = 0; /* reset count register */
reg16(TMR0_CTRL) = (COUNT_MODE<<13) | (PRIME_SRC<<9) | (SEC_SRC<<7) | (ONCE<<6) | (LEN<<5) | (DIR<<4) | (CO_INIT<<3) | (OUT_MODE);
reg16(TMR_ENBL) = 0xf; /* enable all the timers --- why not? */
while(1) {
/* blink on */
reg32(GPIO_DATA0) = 0x00000400;
while((reg16(TMR0_SCTRL)>>15) == 0) { continue; }
reg16(TMR0_SCTRL) = 0; /*clear bit 15, and all the others --- should be ok, but clearly not "the right thing to do" */
/* blink off */
reg32(GPIO_DATA0) = 0x00000000;
while((reg16(TMR0_SCTRL)>>15) == 0) { continue; }
reg16(TMR0_SCTRL) = 0; /*clear bit 15, and all the others --- should be ok, but clearly not "the right thing to do" */
};
}