Minor fixes

examples/zolertia/zoul/test-pm10-sensor.c

@@ -64,13 +64,11 @@ static struct etimer et;
 PROCESS_THREAD(test_pm10_sensor_process, ev, data)
 {
   PROCESS_BEGIN();
-  SENSORS_ACTIVATE(pm10);
 
   static uint16_t pm10_value;
 
-  /* Configure the ADC ports */
   /* Use pin number not mask, for example if using the PA5 pin then use 2 */
-  printf("return configure, %d \n", pm10.configure(SENSORS_ACTIVE, ADC_PIN));
+  pm10.configure(SENSORS_ACTIVE, ADC_PIN);
 
   /* And periodically poll the sensor */
 
@@ -79,8 +77,8 @@ PROCESS_THREAD(test_pm10_sensor_process, ev, data)
     PROCESS_WAIT_EVENT_UNTIL(etimer_expired(&et));
 
     leds_toggle(LEDS_GREEN);
-    printf("PM10 value\n");
     pm10_value = pm10.value(1);
+
     if(pm10_value != ADC_WRAPPER_ERROR) {
       printf("PM10 value = %u ppm\n", pm10_value);
     } else {

platform/zoul/dev/pm10-sensor.c

@@ -49,52 +49,54 @@
 #include "dev/gpio.h"
 #include "dev/ioc.h"
 /*---------------------------------------------------------------------------*/
+#define PM10_SENSOR_PORT_BASE   GPIO_PORT_TO_BASE(PM10_SENSOR_CTRL_PORT)
+#define PM10_SENSOR_PIN_MASK    GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN)
+/*---------------------------------------------------------------------------*/
 static uint8_t enabled;
 /*---------------------------------------------------------------------------*/
-#ifdef PM10_SENSOR_CONF_CTRL_PIN
-#define PM10_SENSOR_CTRL_PIN PM10_SENSOR_CONF_CTRL_PIN
-#else
-#define PM10_SENSOR_CTRL_PIN 0x07
-#endif
-
-#define PM10_SENSOR_PORT GPIO_A_BASE
-
 static int
 configure(int type, int value)
 {
-  int error;
   if(type != SENSORS_ACTIVE) {
     return PM10_ERROR;
   }
 
-  /*Set PA7 as output, used as pulse-driven wave*/
+  if(value) {
-  ioc_set_over(PM10_SENSOR_PORT, PM10_SENSOR_CTRL_PIN, IOC_OVERRIDE_DIS); 
+    /* Set as output, used as pulse-driven wave */
-  GPIO_SOFTWARE_CONTROL(PM10_SENSOR_PORT, GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN));
+    GPIO_SOFTWARE_CONTROL(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
-  GPIO_SET_OUTPUT(PM10_SENSOR_PORT, GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN));
+    ioc_set_over(PM10_SENSOR_CTRL_PORT, PM10_SENSOR_CTRL_PIN, IOC_OVERRIDE_DIS); 
+    GPIO_SET_OUTPUT(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
+    GPIO_CLR_PIN(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
 
-  GPIO_CLR_PIN(PM10_SENSOR_PORT, GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN));
+    enabled = 1;
+    return adc_sensors.configure(ANALOG_PM10_SENSOR, value);
+  }
 
-  /* Use pin number not mask, for example if using the PA5 pin then use 5 */
+  enabled = 0;
-  error = adc_sensors.configure(ANALOG_PM10_SENSOR, value);
+  return PM10_SUCCESS;
-
-  return error;
 }
 /*---------------------------------------------------------------------------*/
 static int
 value(int type)
 {
   uint16_t val;
-  /*Set Pulse Wave pin before measure*/
-  GPIO_SET_PIN(PM10_SENSOR_PORT, GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN));
-  /*Pulse wave delay*/
-  clock_delay_usec(280);
-  /*Data acquisition*/  
-  val = adc_sensors.value(ANALOG_PM10_SENSOR); 
-  /*Clear pulse wave pin*/
-  GPIO_CLR_PIN(PM10_SENSOR_PORT, GPIO_PIN_MASK(PM10_SENSOR_CTRL_PIN));
 
-  /*Applied constant conversion from UAir project*/
+  if(!enabled) {
-  /*to obtain value in ppm (value in mV * 0.28)*/
+    return PM10_ERROR;
+  }
+
+  /* Set Pulse Wave pin before measure */
+  GPIO_SET_PIN(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
+  /* Pulse wave delay */
+  clock_delay_usec(PM10_SENSOR_PULSE_DELAY);
+  /* Data acquisition */  
+  val = adc_sensors.value(ANALOG_PM10_SENSOR); 
+  /* Clear pulse wave pin */
+  GPIO_CLR_PIN(PM10_SENSOR_PORT_BASE, PM10_SENSOR_PIN_MASK);
+  
+  /* Applied constant conversion from UAir project
+   * to obtain value in ppm (value in mV * 0.28)
+   */
   val *= 28;
   val /= 1000;
 

platform/zoul/dev/pm10-sensor.h

@@ -43,17 +43,29 @@
  */
 /*---------------------------------------------------------------------------*/
 #include "lib/sensors.h"
-
+/*---------------------------------------------------------------------------*/
 #ifndef PM10_SENSOR_H_
 #define PM10_SENSOR_H_
-
 /* -------------------------------------------------------------------------- */
-#define PM10_ERROR	-1
+#define PM10_ERROR 	                 (-1)
-#define PM10_SENSOR "PM10 Sensor"
+#define PM10_SUCCESS                 0
+#define PM10_SENSOR                  "PM10 Sensor"
+#define PM10_SENSOR_PULSE_DELAY      280
+/* -------------------------------------------------------------------------- */
+#ifdef PM10_SENSOR_CONF_CTRL_PIN
+#define PM10_SENSOR_CTRL_PIN         PM10_SENSOR_CONF_CTRL_PIN
+#else
+#define PM10_SENSOR_CTRL_PIN         7
+#endif
+#ifdef PM10_SENSOR_CONF_CTRL_PORT
+#define PM10_SENSOR_CTRL_PORT        PM10_SENSOR_CONF_CTRL_PORT
+#else
+#define PM10_SENSOR_CTRL_PORT        GPIO_A_NUM
+#endif
 /* -------------------------------------------------------------------------- */
 extern const struct sensors_sensor pm10;
 /* -------------------------------------------------------------------------- */
-#endif /* ifndef VAC_SENSOR_H_ */
+#endif /* ifndef PM10_SENSOR_H_ */
 /**
  * @}
  * @}