Update to markdown

- Spellchecking
- Update plain text to github markdown

tools/stm32w/stm32w_flasher/README

@@ -1,26 +0,0 @@
-STM32W Flasher 2.0.0b2 for Linux
-
-A programmer for development boards based on STM32W108 microcontroller.
-It works with the following boards (with FT232R or STM32F103 as USB-serial converter):
-MB850, MB851, MB950, MB951, MB954
-
-
-- Installation
-
-	Installation is not required.
-	Hal package has to be present in your system.
-
-
-- Usage
-
-	Run the program with -h option for usage info.
-
-
-- Notes
-
-	This program may require root privileges when programming boards with
-	FT232R chip.
-	In Ubuntu, if you want to flash using Make, type 'sudo -s' before that.
-	 
-	This version of STM32W Flasher does not support jlink yet.
-

tools/stm32w/stm32w_flasher/README.markdown

@@ -0,0 +1,26 @@
+STM32W Flasher 2.0.0b2 for Linux
+================================
+
+A programmer for development boards based on STM32W108 microcontroller.
+It works with the following boards (with FT232R or STM32F103 as USB-serial converter):
+MB850, MB851, MB950, MB951, MB954
+
+Installation
+------------
+
+Installation is not required.
+Hal package has to be present in your system.
+
+
+Usage
+-----
+
+Run the program with -h option for usage info.
+
+
+Notes
+-----
+
+- This program may require root privileges when programming boards with FT232R chip.
+- In Ubuntu, if you want to flash using Make, type 'sudo -s' before that.
+- This version of STM32W Flasher does not support jlink yet.

tools/stm32w/uip6_bridge/README

@@ -1,27 +0,0 @@
-See siscslow_ethernet.c for information about translation between
-802.15.4 and 802.3 addresses.
-Devices must have a proper EUI-64 address for this bridge to work.
-If the EUI-64 address of the devices cannot be changed and they are
-incompatible with the translation mechanism, you have to change the
-translation rules (they are defined in mac_createSicslowpanLongAddr()
-and mac_createEthernetAddr()).
-
-Usage example:
-
-run tapslip6 (source file are located in tools folder).
-
-./tapslip6 -p 2001:db8:bbbb:abce::/64
-
-where 2001:db8:bbbb:abce:: is the network address and 64 is the the
-prefix length. The remaining 64 bits will be derived from the EUI-64 (two
-middle bytes will be removed).
-
-You can also simply create an edge router in one of the network nodes:
-you have to enable routing and set the appropriate forwarding rules, as 
-shown in contiki-init-net.c. Then you have to add the corresponding
-rule on your machine, for example:
-route -A inet6 add 2001:db8:bbbb:abcd::/64 gw 2001:db8:bbbb:abce:
-	280:e102::8a.
-	
-where 2001:db8:bbbb:abce:280:e102::6c is the address of the edge
-node and 2001:db8:bbbb:abcd::/64 is the lowpan address.

tools/stm32w/uip6_bridge/README.markdown

@@ -0,0 +1,26 @@
+See siscslow_ethernet.c for information about translation between 802.15.4 and
+802.3 addresses.  Devices must have a proper EUI-64 address for this bridge to
+work.  If the EUI-64 address of the devices cannot be changed and they are
+incompatible with the translation mechanism, you have to change the translation
+rules (they are defined in mac_createSicslowpanLongAddr() and
+mac_createEthernetAddr()).
+
+Usage example:
+
+    run tapslip6 (source file are located in tools folder).
+
+    ./tapslip6 -p 2001:db8:bbbb:abce::/64
+
+where 2001:db8:bbbb:abce:: is the network address and 64 is the the prefix
+length. The remaining 64 bits will be derived from the EUI-64 (two middle bytes
+will be removed).
+
+You can also simply create an edge router in one of the network nodes: you have
+to enable routing and set the appropriate forwarding rules, as shown in
+contiki-init-net.c. Then you have to add the corresponding rule on your
+machine, for example:
+
+    route -A inet6 add 2001:db8:bbbb:abcd::/64 gw 2001:db8:bbbb:abce:280:e102::8a.
+
+where 2001:db8:bbbb:abce:280:e102::6c is the address of the edge node and
+2001:db8:bbbb:abcd::/64 is the lowpan address.

tools/stm32w/wpcapslip6/README.markdown

@@ -0,0 +1,22 @@
+wpcapslip6
+==========
+
+This software needs a working network adapter. You can install a Microsoft
+Loopback adapter.  (remeber to reboot after the installation procedure).
+
+In order to install this kind of device in Windows 7, use devcon utility (you
+can download it from Microsoft website).
+
+    devcon.exe install %windir%\inf\netloop.inf *msloop
+
+This utility can be used in conjunction with the uip6-bridge or the
+rpl-border-router (the latter on Windows Vista and later only).
+
+An example of usage with the RPL border router:
+
+    wpcapslip6 -s COMXX -b aaaa:: -a aaaa:1::1/128 02-00-00-00-00-01
+
+where 02-00-00-00-00-01 is the MAC address of the local network adapter.
+
+-a aaaa:1::1/128 can be omitted if an IP address is already set to the network
+adapter.

tools/stm32w/wpcapslip6/README.txt

@@ -1,19 +0,0 @@
-This software needs a working network adapter. You can install a Microsoft Loopback adapter.
-(remeber to reboot after the installation procedure).
-
-In order to install this kind of device in Windows 7, use
-devcon utility (you can download it from Microsoft website).
-
-> devcon.exe install %windir%\inf\netloop.inf *msloop
-
-
-This utility can be used in conjunction with the uip6-bridge or the rpl-border-router
-(the latter on Windows Vista and later only).
-
-
-An example of usage with the RPL border router:
-wpcapslip6 -s COMXX -b aaaa:: -a aaaa:1::1/128 02-00-00-00-00-01
-
-where 02-00-00-00-00-01 is the MAC address of the local network adapter.
--a aaaa:1::1/128 can be omitted if an IP address is already set
-to the network adapter.