deac/osd-contiki
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity

bugfix use bmp280 and not bme280

Browse source
This commit is contained in:
Harald Pichler 2017-02-23 22:22:40 +01:00
parent 85f3814f67
commit 6677fac2ab
17 changed files with 1115 additions and 1861 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

502
examples/osd/arduino-bmp280/Adafruit_BME280.cpp
View file

@ -1,502 +0,0 @@
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include "Arduino.h"
#include <Wire.h>
#include <SPI.h>
#include "Adafruit_BME280.h"
/***************************************************************************
PRIVATE FUNCTIONS
***************************************************************************/
Adafruit_BME280::Adafruit_BME280()
: _cs(-1), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BME280::Adafruit_BME280(int8_t cspin)
: _cs(cspin), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BME280::Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin)
: _cs(cspin), _mosi(mosipin), _miso(misopin), _sck(sckpin)
{ }
/**************************************************************************/
/*!
@brief Initialise sensor with given parameters / settings
*/
/**************************************************************************/
bool Adafruit_BME280::begin(uint8_t addr)
{
_i2caddr = addr;
// init I2C or SPI sensor interface
if (_cs == -1) {
// I2C
Wire.begin();
} else {
digitalWrite(_cs, HIGH);
pinMode(_cs, OUTPUT);
if (_sck == -1) {
// hardware SPI
SPI.begin();
} else {
// software SPI
pinMode(_sck, OUTPUT);
pinMode(_mosi, OUTPUT);
pinMode(_miso, INPUT);
}
}
// check if sensor, i.e. the chip ID is correct
if (read8(BME280_REGISTER_CHIPID) != 0x60)
return false;
// reset the device using soft-reset
// this makes sure the IIR is off, etc.
write8(BME280_REGISTER_SOFTRESET, 0xB6);
// wait for chip to wake up.
delay(300);
// if chip is still reading calibration, delay
while (isReadingCalibration())
delay(100);
readCoefficients(); // read trimming parameters, see DS 4.2.2
setSampling(); // use defaults
return true;
}
/**************************************************************************/
/*!
@brief setup sensor with given parameters / settings
This is simply a overload to the normal begin()-function, so SPI users
don't get confused about the library requiring an address.
*/
/**************************************************************************/
void Adafruit_BME280::setSampling(sensor_mode mode,
sensor_sampling tempSampling,
sensor_sampling pressSampling,
sensor_sampling humSampling,
sensor_filter filter,
standby_duration duration) {
_measReg.mode = mode;
_measReg.osrs_t = tempSampling;
_measReg.osrs_p = pressSampling;
_humReg.osrs_h = humSampling;
_configReg.filter = filter;
_configReg.t_sb = duration;
// you must make sure to also set REGISTER_CONTROL after setting the
// CONTROLHUMID register, otherwise the values won't be applied (see DS 5.4.3)
write8(BME280_REGISTER_CONTROLHUMID, _humReg.get());
write8(BME280_REGISTER_CONFIG, _configReg.get());
write8(BME280_REGISTER_CONTROL, _measReg.get());
}
/**************************************************************************/
/*!
@brief Encapsulate hardware and software SPI transfer into one function
*/
/**************************************************************************/
uint8_t Adafruit_BME280::spixfer(uint8_t x) {
// hardware SPI
if (_sck == -1)
return SPI.transfer(x);
// software SPI
uint8_t reply = 0;
for (int i=7; i>=0; i--) {
reply <<= 1;
digitalWrite(_sck, LOW);
digitalWrite(_mosi, x & (1<<i));
digitalWrite(_sck, HIGH);
if (digitalRead(_miso))
reply |= 1;
}
return reply;
}
/**************************************************************************/
/*!
@brief Writes an 8 bit value over I2C or SPI
*/
/**************************************************************************/
void Adafruit_BME280::write8(byte reg, byte value) {
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.write((uint8_t)value);
Wire.endTransmission();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg & ~0x80); // write, bit 7 low
spixfer(value);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
}
/**************************************************************************/
/*!
@brief Reads an 8 bit value over I2C or SPI
*/
/**************************************************************************/
uint8_t Adafruit_BME280::read8(byte reg) {
uint8_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)1);
value = Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Reads a 16 bit value over I2C or SPI
*/
/**************************************************************************/
uint16_t Adafruit_BME280::read16(byte reg)
{
uint16_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)2);
value = (Wire.read() << 8) | Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = (spixfer(0) << 8) | spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
uint16_t Adafruit_BME280::read16_LE(byte reg) {
uint16_t temp = read16(reg);
return (temp >> 8) | (temp << 8);
}
/**************************************************************************/
/*!
@brief Reads a signed 16 bit value over I2C or SPI
*/
/**************************************************************************/
int16_t Adafruit_BME280::readS16(byte reg)
{
return (int16_t)read16(reg);
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
int16_t Adafruit_BME280::readS16_LE(byte reg)
{
return (int16_t)read16_LE(reg);
}
/**************************************************************************/
/*!
@brief Reads a 24 bit value over I2C
*/
/**************************************************************************/
uint32_t Adafruit_BME280::read24(byte reg)
{
uint32_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)3);
value = Wire.read();
value <<= 8;
value |= Wire.read();
value <<= 8;
value |= Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
value <<= 8;
value |= spixfer(0);
value <<= 8;
value |= spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Take a new measurement (only possible in forced mode)
*/
/**************************************************************************/
void Adafruit_BME280::takeForcedMeasurement()
{
// If we are in forced mode, the BME sensor goes back to sleep after each
// measurement and we need to set it to forced mode once at this point, so
// it will take the next measurement and then return to sleep again.
// In normal mode simply does new measurements periodically.
if (_measReg.mode == MODE_FORCED) {
// set to forced mode, i.e. "take next measurement"
write8(BME280_REGISTER_CONTROL, _measReg.get());
// wait until measurement has been completed, otherwise we would read
// the values from the last measurement
while (read8(BME280_REGISTER_STATUS) & 0x08)
delay(1);
}
}
/**************************************************************************/
/*!
@brief Reads the factory-set coefficients
*/
/**************************************************************************/
void Adafruit_BME280::readCoefficients(void)
{
_bme280_calib.dig_T1 = read16_LE(BME280_REGISTER_DIG_T1);
_bme280_calib.dig_T2 = readS16_LE(BME280_REGISTER_DIG_T2);
_bme280_calib.dig_T3 = readS16_LE(BME280_REGISTER_DIG_T3);
_bme280_calib.dig_P1 = read16_LE(BME280_REGISTER_DIG_P1);
_bme280_calib.dig_P2 = readS16_LE(BME280_REGISTER_DIG_P2);
_bme280_calib.dig_P3 = readS16_LE(BME280_REGISTER_DIG_P3);
_bme280_calib.dig_P4 = readS16_LE(BME280_REGISTER_DIG_P4);
_bme280_calib.dig_P5 = readS16_LE(BME280_REGISTER_DIG_P5);
_bme280_calib.dig_P6 = readS16_LE(BME280_REGISTER_DIG_P6);
_bme280_calib.dig_P7 = readS16_LE(BME280_REGISTER_DIG_P7);
_bme280_calib.dig_P8 = readS16_LE(BME280_REGISTER_DIG_P8);
_bme280_calib.dig_P9 = readS16_LE(BME280_REGISTER_DIG_P9);
_bme280_calib.dig_H1 = read8(BME280_REGISTER_DIG_H1);
_bme280_calib.dig_H2 = readS16_LE(BME280_REGISTER_DIG_H2);
_bme280_calib.dig_H3 = read8(BME280_REGISTER_DIG_H3);
_bme280_calib.dig_H4 = (read8(BME280_REGISTER_DIG_H4) << 4) | (read8(BME280_REGISTER_DIG_H4+1) & 0xF);
_bme280_calib.dig_H5 = (read8(BME280_REGISTER_DIG_H5+1) << 4) | (read8(BME280_REGISTER_DIG_H5) >> 4);
_bme280_calib.dig_H6 = (int8_t)read8(BME280_REGISTER_DIG_H6);
}
/**************************************************************************/
/*!
@brief return true if chip is busy reading cal data
*/
/**************************************************************************/
bool Adafruit_BME280::isReadingCalibration(void)
{
uint8_t const rStatus = read8(BME280_REGISTER_STATUS);
return (rStatus & (1 << 0)) != 0;
}
/**************************************************************************/
/*!
@brief Returns the temperature from the sensor
*/
/**************************************************************************/
float Adafruit_BME280::readTemperature(void)
{
int32_t var1, var2;
int32_t adc_T = read24(BME280_REGISTER_TEMPDATA);
if (adc_T == 0x800000) // value in case temp measurement was disabled
return NAN;
adc_T >>= 4;
var1 = ((((adc_T>>3) - ((int32_t)_bme280_calib.dig_T1 <<1))) *
((int32_t)_bme280_calib.dig_T2)) >> 11;
var2 = (((((adc_T>>4) - ((int32_t)_bme280_calib.dig_T1)) *
((adc_T>>4) - ((int32_t)_bme280_calib.dig_T1))) >> 12) *
((int32_t)_bme280_calib.dig_T3)) >> 14;
t_fine = var1 + var2;
float T = (t_fine * 5 + 128) >> 8;
return T/100;
}
/**************************************************************************/
/*!
@brief Returns the temperature from the sensor
*/
/**************************************************************************/
float Adafruit_BME280::readPressure(void) {
int64_t var1, var2, p;
readTemperature(); // must be done first to get t_fine
int32_t adc_P = read24(BME280_REGISTER_PRESSUREDATA);
if (adc_P == 0x800000) // value in case pressure measurement was disabled
return NAN;
adc_P >>= 4;
var1 = ((int64_t)t_fine) - 128000;
var2 = var1 * var1 * (int64_t)_bme280_calib.dig_P6;
var2 = var2 + ((var1*(int64_t)_bme280_calib.dig_P5)<<17);
var2 = var2 + (((int64_t)_bme280_calib.dig_P4)<<35);
var1 = ((var1 * var1 * (int64_t)_bme280_calib.dig_P3)>>8) +
((var1 * (int64_t)_bme280_calib.dig_P2)<<12);
var1 = (((((int64_t)1)<<47)+var1))*((int64_t)_bme280_calib.dig_P1)>>33;
if (var1 == 0) {
return 0; // avoid exception caused by division by zero
}
p = 1048576 - adc_P;
p = (((p<<31) - var2)*3125) / var1;
var1 = (((int64_t)_bme280_calib.dig_P9) * (p>>13) * (p>>13)) >> 25;
var2 = (((int64_t)_bme280_calib.dig_P8) * p) >> 19;
p = ((p + var1 + var2) >> 8) + (((int64_t)_bme280_calib.dig_P7)<<4);
return (float)p/256;
}
/**************************************************************************/
/*!
@brief Returns the humidity from the sensor
*/
/**************************************************************************/
float Adafruit_BME280::readHumidity(void) {
readTemperature(); // must be done first to get t_fine
int32_t adc_H = read16(BME280_REGISTER_HUMIDDATA);
if (adc_H == 0x8000) // value in case humidity measurement was disabled
return NAN;
int32_t v_x1_u32r;
v_x1_u32r = (t_fine - ((int32_t)76800));
v_x1_u32r = (((((adc_H << 14) - (((int32_t)_bme280_calib.dig_H4) << 20) -
(((int32_t)_bme280_calib.dig_H5) * v_x1_u32r)) + ((int32_t)16384)) >> 15) *
(((((((v_x1_u32r * ((int32_t)_bme280_calib.dig_H6)) >> 10) *
(((v_x1_u32r * ((int32_t)_bme280_calib.dig_H3)) >> 11) + ((int32_t)32768))) >> 10) +
((int32_t)2097152)) * ((int32_t)_bme280_calib.dig_H2) + 8192) >> 14));
v_x1_u32r = (v_x1_u32r - (((((v_x1_u32r >> 15) * (v_x1_u32r >> 15)) >> 7) *
((int32_t)_bme280_calib.dig_H1)) >> 4));
v_x1_u32r = (v_x1_u32r < 0) ? 0 : v_x1_u32r;
v_x1_u32r = (v_x1_u32r > 419430400) ? 419430400 : v_x1_u32r;
float h = (v_x1_u32r>>12);
return h / 1024.0;
}
/**************************************************************************/
/*!
Calculates the altitude (in meters) from the specified atmospheric
pressure (in hPa), and sea-level pressure (in hPa).
@param seaLevel Sea-level pressure in hPa
@param atmospheric Atmospheric pressure in hPa
*/
/**************************************************************************/
float Adafruit_BME280::readAltitude(float seaLevel)
{
// Equation taken from BMP180 datasheet (page 16):
// http://www.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
// Note that using the equation from wikipedia can give bad results
// at high altitude. See this thread for more information:
// http://forums.adafruit.com/viewtopic.php?f=22&t=58064
float atmospheric = readPressure() / 100.0F;
return 44330.0 * (1.0 - pow(atmospheric / seaLevel, 0.1903));
}
/**************************************************************************/
/*!
Calculates the pressure at sea level (in hPa) from the specified altitude
(in meters), and atmospheric pressure (in hPa).
@param altitude Altitude in meters
@param atmospheric Atmospheric pressure in hPa
*/
/**************************************************************************/
float Adafruit_BME280::seaLevelForAltitude(float altitude, float atmospheric)
{
// Equation taken from BMP180 datasheet (page 17):
// http://www.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
// Note that using the equation from wikipedia can give bad results
// at high altitude. See this thread for more information:
// http://forums.adafruit.com/viewtopic.php?f=22&t=58064
return atmospheric / pow(1.0 - (altitude/44330.0), 5.255);
}

290
examples/osd/arduino-bmp280/Adafruit_BME280.h
View file

@ -1,290 +0,0 @@
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#ifndef __BME280_H__
#define __BME280_H__
#include "Arduino.h"
#include <Adafruit_Sensor.h>
#include <Wire.h>
/*=========================================================================
I2C ADDRESS/BITS
-----------------------------------------------------------------------*/
#define BME280_ADDRESS (0x77)
/*=========================================================================*/
/*=========================================================================
REGISTERS
-----------------------------------------------------------------------*/
enum
{
BME280_REGISTER_DIG_T1 = 0x88,
BME280_REGISTER_DIG_T2 = 0x8A,
BME280_REGISTER_DIG_T3 = 0x8C,
BME280_REGISTER_DIG_P1 = 0x8E,
BME280_REGISTER_DIG_P2 = 0x90,
BME280_REGISTER_DIG_P3 = 0x92,
BME280_REGISTER_DIG_P4 = 0x94,
BME280_REGISTER_DIG_P5 = 0x96,
BME280_REGISTER_DIG_P6 = 0x98,
BME280_REGISTER_DIG_P7 = 0x9A,
BME280_REGISTER_DIG_P8 = 0x9C,
BME280_REGISTER_DIG_P9 = 0x9E,
BME280_REGISTER_DIG_H1 = 0xA1,
BME280_REGISTER_DIG_H2 = 0xE1,
BME280_REGISTER_DIG_H3 = 0xE3,
BME280_REGISTER_DIG_H4 = 0xE4,
BME280_REGISTER_DIG_H5 = 0xE5,
BME280_REGISTER_DIG_H6 = 0xE7,
BME280_REGISTER_CHIPID = 0xD0,
BME280_REGISTER_VERSION = 0xD1,
BME280_REGISTER_SOFTRESET = 0xE0,
BME280_REGISTER_CAL26 = 0xE1, // R calibration stored in 0xE1-0xF0
BME280_REGISTER_CONTROLHUMID = 0xF2,
BME280_REGISTER_STATUS = 0XF3,
BME280_REGISTER_CONTROL = 0xF4,
BME280_REGISTER_CONFIG = 0xF5,
BME280_REGISTER_PRESSUREDATA = 0xF7,
BME280_REGISTER_TEMPDATA = 0xFA,
BME280_REGISTER_HUMIDDATA = 0xFD
};
/*=========================================================================*/
/*=========================================================================
CALIBRATION DATA
-----------------------------------------------------------------------*/
typedef struct
{
uint16_t dig_T1;
int16_t dig_T2;
int16_t dig_T3;
uint16_t dig_P1;
int16_t dig_P2;
int16_t dig_P3;
int16_t dig_P4;
int16_t dig_P5;
int16_t dig_P6;
int16_t dig_P7;
int16_t dig_P8;
int16_t dig_P9;
uint8_t dig_H1;
int16_t dig_H2;
uint8_t dig_H3;
int16_t dig_H4;
int16_t dig_H5;
int8_t dig_H6;
} bme280_calib_data;
/*=========================================================================*/
/*
class Adafruit_BME280_Unified : public Adafruit_Sensor
{
public:
Adafruit_BME280_Unified(int32_t sensorID = -1);
bool begin(uint8_t addr = BME280_ADDRESS);
void getTemperature(float *temp);
void getPressure(float *pressure);
float pressureToAltitude(float seaLevel, float atmospheric, float temp);
float seaLevelForAltitude(float altitude, float atmospheric, float temp);
void getEvent(sensors_event_t*);
void getSensor(sensor_t*);
private:
uint8_t _i2c_addr;
int32_t _sensorID;
};
*/
class Adafruit_BME280 {
public:
enum sensor_sampling {
SAMPLING_NONE = 0b000,
SAMPLING_X1 = 0b001,
SAMPLING_X2 = 0b010,
SAMPLING_X4 = 0b011,
SAMPLING_X8 = 0b100,
SAMPLING_X16 = 0b101
};
enum sensor_mode {
MODE_SLEEP = 0b00,
MODE_FORCED = 0b01,
MODE_NORMAL = 0b11
};
enum sensor_filter {
FILTER_OFF = 0b000,
FILTER_X2 = 0b001,
FILTER_X4 = 0b010,
FILTER_X8 = 0b011,
FILTER_X16 = 0b100
};
// standby durations in ms
enum standby_duration {
STANDBY_MS_0_5 = 0b000,
STANDBY_MS_10 = 0b110,
STANDBY_MS_20 = 0b111,
STANDBY_MS_62_5 = 0b001,
STANDBY_MS_125 = 0b010,
STANDBY_MS_250 = 0b011,
STANDBY_MS_500 = 0b100,
STANDBY_MS_1000 = 0b101
};
// constructors
Adafruit_BME280(void);
Adafruit_BME280(int8_t cspin);
Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
bool begin(uint8_t addr = BME280_ADDRESS);
void setSampling(sensor_mode mode = MODE_NORMAL,
sensor_sampling tempSampling = SAMPLING_X16,
sensor_sampling pressSampling = SAMPLING_X16,
sensor_sampling humSampling = SAMPLING_X16,
sensor_filter filter = FILTER_OFF,
standby_duration duration = STANDBY_MS_0_5
);
void takeForcedMeasurement();
float readTemperature(void);
float readPressure(void);
float readHumidity(void);
float readAltitude(float seaLevel);
float seaLevelForAltitude(float altitude, float pressure);
private:
void readCoefficients(void);
bool isReadingCalibration(void);
uint8_t spixfer(uint8_t x);
void write8(byte reg, byte value);
uint8_t read8(byte reg);
uint16_t read16(byte reg);
uint32_t read24(byte reg);
int16_t readS16(byte reg);
uint16_t read16_LE(byte reg); // little endian
int16_t readS16_LE(byte reg); // little endian
uint8_t _i2caddr;
int32_t _sensorID;
int32_t t_fine;
int8_t _cs, _mosi, _miso, _sck;
bme280_calib_data _bme280_calib;
// The config register
struct config {
// inactive duration (standby time) in normal mode
// 000 = 0.5 ms
// 001 = 62.5 ms
// 010 = 125 ms
// 011 = 250 ms
// 100 = 500 ms
// 101 = 1000 ms
// 110 = 10 ms
// 111 = 20 ms
unsigned int t_sb : 3;
// filter settings
// 000 = filter off
// 001 = 2x filter
// 010 = 4x filter
// 011 = 8x filter
// 100 and above = 16x filter
unsigned int filter : 3;
// unused - don't set
unsigned int none : 1;
unsigned int spi3w_en : 1;
unsigned int get() {
return (t_sb << 5) | (filter << 3) | spi3w_en;
}
};
config _configReg;
// The ctrl_meas register
struct ctrl_meas {
// temperature oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_t : 3;
// pressure oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_p : 3;
// device mode
// 00 = sleep
// 01 or 10 = forced
// 11 = normal
unsigned int mode : 2;
unsigned int get() {
return (osrs_t << 5) | (osrs_p << 3) | mode;
}
};
ctrl_meas _measReg;
// The ctrl_hum register
struct ctrl_hum {
// unused - don't set
unsigned int none : 5;
// pressure oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_h : 3;
unsigned int get() {
return (osrs_h);
}
};
ctrl_hum _humReg;
};
#endif

325
examples/osd/arduino-bmp280/Adafruit_BMP280.cpp Normal file
View file

@ -0,0 +1,325 @@
/***************************************************************************
This is a library for the BMP280 pressure sensor
Designed specifically to work with the Adafruit BMP280 Breakout
----> http://www.adafruit.com/products/2651
These sensors use I2C to communicate, 2 pins are required to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include "Arduino.h"
#include <Wire.h>
#include <SPI.h>
#include "Adafruit_BMP280.h"
/***************************************************************************
PRIVATE FUNCTIONS
***************************************************************************/
Adafruit_BMP280::Adafruit_BMP280()
: _cs(-1), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BMP280::Adafruit_BMP280(int8_t cspin)
: _cs(cspin), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BMP280::Adafruit_BMP280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin)
: _cs(cspin), _mosi(mosipin), _miso(misopin), _sck(sckpin)
{ }
bool Adafruit_BMP280::begin(uint8_t a, uint8_t chipid) {
_i2caddr = a;
if (_cs == -1) {
// i2c
Wire.begin();
} else {
digitalWrite(_cs, HIGH);
pinMode(_cs, OUTPUT);
if (_sck == -1) {
// hardware SPI
SPI.begin();
} else {
// software SPI
pinMode(_sck, OUTPUT);
pinMode(_mosi, OUTPUT);
pinMode(_miso, INPUT);
}
}
if (read8(BMP280_REGISTER_CHIPID) != chipid)
return false;
readCoefficients();
write8(BMP280_REGISTER_CONTROL, 0x3F);
return true;
}
uint8_t Adafruit_BMP280::spixfer(uint8_t x) {
if (_sck == -1)
return SPI.transfer(x);
// software spi
//Serial.println("Software SPI");
uint8_t reply = 0;
for (int i=7; i>=0; i--) {
reply <<= 1;
digitalWrite(_sck, LOW);
digitalWrite(_mosi, x & (1<<i));
digitalWrite(_sck, HIGH);
if (digitalRead(_miso))
reply |= 1;
}
return reply;
}
/**************************************************************************/
/*!
@brief Writes an 8 bit value over I2C/SPI
*/
/**************************************************************************/
void Adafruit_BMP280::write8(byte reg, byte value)
{
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.write((uint8_t)value);
Wire.endTransmission();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg & ~0x80); // write, bit 7 low
spixfer(value);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
}
/**************************************************************************/
/*!
@brief Reads an 8 bit value over I2C/SPI
*/
/**************************************************************************/
uint8_t Adafruit_BMP280::read8(byte reg)
{
uint8_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)1);
value = Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Reads a 16 bit value over I2C/SPI
*/
/**************************************************************************/
uint16_t Adafruit_BMP280::read16(byte reg)
{
uint16_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)2);
value = (Wire.read() << 8) | Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = (spixfer(0) << 8) | spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
uint16_t Adafruit_BMP280::read16_LE(byte reg) {
uint16_t temp = read16(reg);
return (temp >> 8) | (temp << 8);
}
/**************************************************************************/
/*!
@brief Reads a signed 16 bit value over I2C/SPI
*/
/**************************************************************************/
int16_t Adafruit_BMP280::readS16(byte reg)
{
return (int16_t)read16(reg);
}
int16_t Adafruit_BMP280::readS16_LE(byte reg)
{
return (int16_t)read16_LE(reg);
}
/**************************************************************************/
/*!
@brief Reads a 24 bit value over I2C/SPI
*/
/**************************************************************************/
uint32_t Adafruit_BMP280::read24(byte reg)
{
uint32_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)3);
value = Wire.read();
value <<= 8;
value |= Wire.read();
value <<= 8;
value |= Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
value <<= 8;
value |= spixfer(0);
value <<= 8;
value |= spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Reads the factory-set coefficients
*/
/**************************************************************************/
void Adafruit_BMP280::readCoefficients(void)
{
_bmp280_calib.dig_T1 = read16_LE(BMP280_REGISTER_DIG_T1);
_bmp280_calib.dig_T2 = readS16_LE(BMP280_REGISTER_DIG_T2);
_bmp280_calib.dig_T3 = readS16_LE(BMP280_REGISTER_DIG_T3);
_bmp280_calib.dig_P1 = read16_LE(BMP280_REGISTER_DIG_P1);
_bmp280_calib.dig_P2 = readS16_LE(BMP280_REGISTER_DIG_P2);
_bmp280_calib.dig_P3 = readS16_LE(BMP280_REGISTER_DIG_P3);
_bmp280_calib.dig_P4 = readS16_LE(BMP280_REGISTER_DIG_P4);
_bmp280_calib.dig_P5 = readS16_LE(BMP280_REGISTER_DIG_P5);
_bmp280_calib.dig_P6 = readS16_LE(BMP280_REGISTER_DIG_P6);
_bmp280_calib.dig_P7 = readS16_LE(BMP280_REGISTER_DIG_P7);
_bmp280_calib.dig_P8 = readS16_LE(BMP280_REGISTER_DIG_P8);
_bmp280_calib.dig_P9 = readS16_LE(BMP280_REGISTER_DIG_P9);
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
float Adafruit_BMP280::readTemperature(void)
{
int32_t var1, var2;
int32_t adc_T = read24(BMP280_REGISTER_TEMPDATA);
adc_T >>= 4;
var1 = ((((adc_T>>3) - ((int32_t)_bmp280_calib.dig_T1 <<1))) *
((int32_t)_bmp280_calib.dig_T2)) >> 11;
var2 = (((((adc_T>>4) - ((int32_t)_bmp280_calib.dig_T1)) *
((adc_T>>4) - ((int32_t)_bmp280_calib.dig_T1))) >> 12) *
((int32_t)_bmp280_calib.dig_T3)) >> 14;
t_fine = var1 + var2;
float T = (t_fine * 5 + 128) >> 8;
return T/100;
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
float Adafruit_BMP280::readPressure(void) {
int64_t var1, var2, p;
// Must be done first to get the t_fine variable set up
readTemperature();
int32_t adc_P = read24(BMP280_REGISTER_PRESSUREDATA);
adc_P >>= 4;
var1 = ((int64_t)t_fine) - 128000;
var2 = var1 * var1 * (int64_t)_bmp280_calib.dig_P6;
var2 = var2 + ((var1*(int64_t)_bmp280_calib.dig_P5)<<17);
var2 = var2 + (((int64_t)_bmp280_calib.dig_P4)<<35);
var1 = ((var1 * var1 * (int64_t)_bmp280_calib.dig_P3)>>8) +
((var1 * (int64_t)_bmp280_calib.dig_P2)<<12);
var1 = (((((int64_t)1)<<47)+var1))*((int64_t)_bmp280_calib.dig_P1)>>33;
if (var1 == 0) {
return 0; // avoid exception caused by division by zero
}
p = 1048576 - adc_P;
p = (((p<<31) - var2)*3125) / var1;
var1 = (((int64_t)_bmp280_calib.dig_P9) * (p>>13) * (p>>13)) >> 25;
var2 = (((int64_t)_bmp280_calib.dig_P8) * p) >> 19;
p = ((p + var1 + var2) >> 8) + (((int64_t)_bmp280_calib.dig_P7)<<4);
return (float)p/256;
}
float Adafruit_BMP280::readAltitude(float seaLevelhPa) {
float altitude;
float pressure = readPressure(); // in Si units for Pascal
pressure /= 100;
altitude = 44330 * (1.0 - pow(pressure / seaLevelhPa, 0.1903));
return altitude;
}

153
examples/osd/arduino-bmp280/Adafruit_BMP280.h Normal file
View file

@ -0,0 +1,153 @@
/***************************************************************************
This is a library for the BMP280 pressure sensor
Designed specifically to work with the Adafruit BMP280 Breakout
----> http://www.adafruit.com/products/2651
These sensors use I2C to communicate, 2 pins are required to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#ifndef __BMP280_H__
#define __BMP280_H__
#include "Arduino.h"
#include <Adafruit_Sensor.h>
#ifdef __AVR_ATtiny85__
#include "TinyWireM.h"
#define Wire TinyWireM
#else
#include <Wire.h>
#endif
/*=========================================================================
I2C ADDRESS/BITS/SETTINGS
-----------------------------------------------------------------------*/
#define BMP280_ADDRESS (0x77)
#define BMP280_CHIPID (0x58)
/*=========================================================================*/
/*=========================================================================
REGISTERS
-----------------------------------------------------------------------*/
enum
{
BMP280_REGISTER_DIG_T1 = 0x88,
BMP280_REGISTER_DIG_T2 = 0x8A,
BMP280_REGISTER_DIG_T3 = 0x8C,
BMP280_REGISTER_DIG_P1 = 0x8E,
BMP280_REGISTER_DIG_P2 = 0x90,
BMP280_REGISTER_DIG_P3 = 0x92,
BMP280_REGISTER_DIG_P4 = 0x94,
BMP280_REGISTER_DIG_P5 = 0x96,
BMP280_REGISTER_DIG_P6 = 0x98,
BMP280_REGISTER_DIG_P7 = 0x9A,
BMP280_REGISTER_DIG_P8 = 0x9C,
BMP280_REGISTER_DIG_P9 = 0x9E,
BMP280_REGISTER_CHIPID = 0xD0,
BMP280_REGISTER_VERSION = 0xD1,
BMP280_REGISTER_SOFTRESET = 0xE0,
BMP280_REGISTER_CAL26 = 0xE1, // R calibration stored in 0xE1-0xF0
BMP280_REGISTER_CONTROL = 0xF4,
BMP280_REGISTER_CONFIG = 0xF5,
BMP280_REGISTER_PRESSUREDATA = 0xF7,
BMP280_REGISTER_TEMPDATA = 0xFA,
};
/*=========================================================================*/
/*=========================================================================
CALIBRATION DATA
-----------------------------------------------------------------------*/
typedef struct
{
uint16_t dig_T1;
int16_t dig_T2;
int16_t dig_T3;
uint16_t dig_P1;
int16_t dig_P2;
int16_t dig_P3;
int16_t dig_P4;
int16_t dig_P5;
int16_t dig_P6;
int16_t dig_P7;
int16_t dig_P8;
int16_t dig_P9;
uint8_t dig_H1;
int16_t dig_H2;
uint8_t dig_H3;
int16_t dig_H4;
int16_t dig_H5;
int8_t dig_H6;
} bmp280_calib_data;
/*=========================================================================*/
/*
class Adafruit_BMP280_Unified : public Adafruit_Sensor
{
public:
Adafruit_BMP280_Unified(int32_t sensorID = -1);
bool begin(uint8_t addr = BMP280_ADDRESS, uint8_t chipid = BMP280_CHIPID);
void getTemperature(float *temp);
void getPressure(float *pressure);
float pressureToAltitude(float seaLevel, float atmospheric, float temp);
float seaLevelForAltitude(float altitude, float atmospheric, float temp);
void getEvent(sensors_event_t*);
void getSensor(sensor_t*);
private:
uint8_t _i2c_addr;
int32_t _sensorID;
};
*/
class Adafruit_BMP280
{
public:
Adafruit_BMP280();
Adafruit_BMP280(int8_t cspin);
Adafruit_BMP280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
bool begin(uint8_t addr = BMP280_ADDRESS, uint8_t chipid = BMP280_CHIPID);
float readTemperature(void);
float readPressure(void);
float readAltitude(float seaLevelhPa = 1013.25);
private:
void readCoefficients(void);
uint8_t spixfer(uint8_t x);
void write8(byte reg, byte value);
uint8_t read8(byte reg);
uint16_t read16(byte reg);
uint32_t read24(byte reg);
int16_t readS16(byte reg);
uint16_t read16_LE(byte reg); // little endian
int16_t readS16_LE(byte reg); // little endian
uint8_t _i2caddr;
int32_t _sensorID;
int32_t t_fine;
int8_t _cs, _mosi, _miso, _sck;
bmp280_calib_data _bmp280_calib;
};
#endif

46
examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/.github/ISSUE_TEMPLATE.md vendored Normal file
View file

@ -0,0 +1,46 @@
Thank you for opening an issue on an Adafruit Arduino library repository. To
improve the speed of resolution please review the following guidelines and
common troubleshooting steps below before creating the issue:
- **Do not use GitHub issues for troubleshooting projects and issues.** Instead use
the forums at http://forums.adafruit.com to ask questions and troubleshoot why
something isn't working as expected. In many cases the problem is a common issue
that you will more quickly receive help from the forum community. GitHub issues
are meant for known defects in the code. If you don't know if there is a defect
in the code then start with troubleshooting on the forum first.
- **If following a tutorial or guide be sure you didn't miss a step.** Carefully
check all of the steps and commands to run have been followed. Consult the
forum if you're unsure or have questions about steps in a guide/tutorial.
- **For Arduino projects check these very common issues to ensure they don't apply**:
- For uploading sketches or communicating with the board make sure you're using
a **USB data cable** and **not** a **USB charge-only cable**. It is sometimes
very hard to tell the difference between a data and charge cable! Try using the
cable with other devices or swapping to another cable to confirm it is not
the problem.
- **Be sure you are supplying adequate power to the board.** Check the specs of
your board and plug in an external power supply. In many cases just
plugging a board into your computer is not enough to power it and other
peripherals.
- **Double check all soldering joints and connections.** Flakey connections
cause many mysterious problems. See the [guide to excellent soldering](https://learn.adafruit.com/adafruit-guide-excellent-soldering/tools) for examples of good solder joints.
- **Ensure you are using an official Arduino or Adafruit board.** We can't
guarantee a clone board will have the same functionality and work as expected
with this code and don't support them.
If you're sure this issue is a defect in the code and checked the steps above
please fill in the following fields to provide enough troubleshooting information.
You may delete the guideline and text above to just leave the following details:
- Arduino board: **INSERT ARDUINO BOARD NAME/TYPE HERE**
- Arduino IDE version (found in Arduino -> About Arduino menu): **INSERT ARDUINO
VERSION HERE**
- List the steps to reproduce the problem below (if possible attach a sketch or
copy the sketch code in too): **LIST REPRO STEPS BELOW**

26
examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/.github/PULL_REQUEST_TEMPLATE.md vendored Normal file
View file

@ -0,0 +1,26 @@
Thank you for creating a pull request to contribute to Adafruit's GitHub code!
Before you open the request please review the following guidelines and tips to
help it be more easily integrated:
- **Describe the scope of your change--i.e. what the change does and what parts
of the code were modified.** This will help us understand any risks of integrating
the code.
- **Describe any known limitations with your change.** For example if the change
doesn't apply to a supported platform of the library please mention it.
- **Please run any tests or examples that can exercise your modified code.** We
strive to not break users of the code and running tests/examples helps with this
process.
Thank you again for contributing! We will try to test and integrate the change
as soon as we can, but be aware we have many GitHub repositories to manage and
can't immediately respond to every request. There is no need to bump or check in
on a pull request (it will clutter the discussion of the request).
Also don't be worried if the request is closed or not integrated--sometimes the
priorities of Adafruit's GitHub code (education, ease of use) might not match the
priorities of the pull request. Don't fret, the open source community thrives on
forks and GitHub makes it easy to keep your changes in a forked repo.
After reviewing the guidelines above you can delete this text from the pull request.

325
examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/Adafruit_BMP280.cpp Normal file
View file

@ -0,0 +1,325 @@
/***************************************************************************
This is a library for the BMP280 pressure sensor
Designed specifically to work with the Adafruit BMP280 Breakout
----> http://www.adafruit.com/products/2651
These sensors use I2C to communicate, 2 pins are required to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include "Arduino.h"
#include <Wire.h>
#include <SPI.h>
#include "Adafruit_BMP280.h"
/***************************************************************************
PRIVATE FUNCTIONS
***************************************************************************/
Adafruit_BMP280::Adafruit_BMP280()
: _cs(-1), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BMP280::Adafruit_BMP280(int8_t cspin)
: _cs(cspin), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BMP280::Adafruit_BMP280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin)
: _cs(cspin), _mosi(mosipin), _miso(misopin), _sck(sckpin)
{ }
bool Adafruit_BMP280::begin(uint8_t a, uint8_t chipid) {
_i2caddr = a;
if (_cs == -1) {
// i2c
Wire.begin();
} else {
digitalWrite(_cs, HIGH);
pinMode(_cs, OUTPUT);
if (_sck == -1) {
// hardware SPI
SPI.begin();
} else {
// software SPI
pinMode(_sck, OUTPUT);
pinMode(_mosi, OUTPUT);
pinMode(_miso, INPUT);
}
}
if (read8(BMP280_REGISTER_CHIPID) != chipid)
return false;
readCoefficients();
write8(BMP280_REGISTER_CONTROL, 0x3F);
return true;
}
uint8_t Adafruit_BMP280::spixfer(uint8_t x) {
if (_sck == -1)
return SPI.transfer(x);
// software spi
//Serial.println("Software SPI");
uint8_t reply = 0;
for (int i=7; i>=0; i--) {
reply <<= 1;
digitalWrite(_sck, LOW);
digitalWrite(_mosi, x & (1<<i));
digitalWrite(_sck, HIGH);
if (digitalRead(_miso))
reply |= 1;
}
return reply;
}
/**************************************************************************/
/*!
@brief Writes an 8 bit value over I2C/SPI
*/
/**************************************************************************/
void Adafruit_BMP280::write8(byte reg, byte value)
{
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.write((uint8_t)value);
Wire.endTransmission();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg & ~0x80); // write, bit 7 low
spixfer(value);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
}
/**************************************************************************/
/*!
@brief Reads an 8 bit value over I2C/SPI
*/
/**************************************************************************/
uint8_t Adafruit_BMP280::read8(byte reg)
{
uint8_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)1);
value = Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Reads a 16 bit value over I2C/SPI
*/
/**************************************************************************/
uint16_t Adafruit_BMP280::read16(byte reg)
{
uint16_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)2);
value = (Wire.read() << 8) | Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = (spixfer(0) << 8) | spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
uint16_t Adafruit_BMP280::read16_LE(byte reg) {
uint16_t temp = read16(reg);
return (temp >> 8) | (temp << 8);
}
/**************************************************************************/
/*!
@brief Reads a signed 16 bit value over I2C/SPI
*/
/**************************************************************************/
int16_t Adafruit_BMP280::readS16(byte reg)
{
return (int16_t)read16(reg);
}
int16_t Adafruit_BMP280::readS16_LE(byte reg)
{
return (int16_t)read16_LE(reg);
}
/**************************************************************************/
/*!
@brief Reads a 24 bit value over I2C/SPI
*/
/**************************************************************************/
uint32_t Adafruit_BMP280::read24(byte reg)
{
uint32_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)3);
value = Wire.read();
value <<= 8;
value |= Wire.read();
value <<= 8;
value |= Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
value <<= 8;
value |= spixfer(0);
value <<= 8;
value |= spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Reads the factory-set coefficients
*/
/**************************************************************************/
void Adafruit_BMP280::readCoefficients(void)
{
_bmp280_calib.dig_T1 = read16_LE(BMP280_REGISTER_DIG_T1);
_bmp280_calib.dig_T2 = readS16_LE(BMP280_REGISTER_DIG_T2);
_bmp280_calib.dig_T3 = readS16_LE(BMP280_REGISTER_DIG_T3);
_bmp280_calib.dig_P1 = read16_LE(BMP280_REGISTER_DIG_P1);
_bmp280_calib.dig_P2 = readS16_LE(BMP280_REGISTER_DIG_P2);
_bmp280_calib.dig_P3 = readS16_LE(BMP280_REGISTER_DIG_P3);
_bmp280_calib.dig_P4 = readS16_LE(BMP280_REGISTER_DIG_P4);
_bmp280_calib.dig_P5 = readS16_LE(BMP280_REGISTER_DIG_P5);
_bmp280_calib.dig_P6 = readS16_LE(BMP280_REGISTER_DIG_P6);
_bmp280_calib.dig_P7 = readS16_LE(BMP280_REGISTER_DIG_P7);
_bmp280_calib.dig_P8 = readS16_LE(BMP280_REGISTER_DIG_P8);
_bmp280_calib.dig_P9 = readS16_LE(BMP280_REGISTER_DIG_P9);
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
float Adafruit_BMP280::readTemperature(void)
{
int32_t var1, var2;
int32_t adc_T = read24(BMP280_REGISTER_TEMPDATA);
adc_T >>= 4;
var1 = ((((adc_T>>3) - ((int32_t)_bmp280_calib.dig_T1 <<1))) *
((int32_t)_bmp280_calib.dig_T2)) >> 11;
var2 = (((((adc_T>>4) - ((int32_t)_bmp280_calib.dig_T1)) *
((adc_T>>4) - ((int32_t)_bmp280_calib.dig_T1))) >> 12) *
((int32_t)_bmp280_calib.dig_T3)) >> 14;
t_fine = var1 + var2;
float T = (t_fine * 5 + 128) >> 8;
return T/100;
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
float Adafruit_BMP280::readPressure(void) {
int64_t var1, var2, p;
// Must be done first to get the t_fine variable set up
readTemperature();
int32_t adc_P = read24(BMP280_REGISTER_PRESSUREDATA);
adc_P >>= 4;
var1 = ((int64_t)t_fine) - 128000;
var2 = var1 * var1 * (int64_t)_bmp280_calib.dig_P6;
var2 = var2 + ((var1*(int64_t)_bmp280_calib.dig_P5)<<17);
var2 = var2 + (((int64_t)_bmp280_calib.dig_P4)<<35);
var1 = ((var1 * var1 * (int64_t)_bmp280_calib.dig_P3)>>8) +
((var1 * (int64_t)_bmp280_calib.dig_P2)<<12);
var1 = (((((int64_t)1)<<47)+var1))*((int64_t)_bmp280_calib.dig_P1)>>33;
if (var1 == 0) {
return 0; // avoid exception caused by division by zero
}
p = 1048576 - adc_P;
p = (((p<<31) - var2)*3125) / var1;
var1 = (((int64_t)_bmp280_calib.dig_P9) * (p>>13) * (p>>13)) >> 25;
var2 = (((int64_t)_bmp280_calib.dig_P8) * p) >> 19;
p = ((p + var1 + var2) >> 8) + (((int64_t)_bmp280_calib.dig_P7)<<4);
return (float)p/256;
}
float Adafruit_BMP280::readAltitude(float seaLevelhPa) {
float altitude;
float pressure = readPressure(); // in Si units for Pascal
pressure /= 100;
altitude = 44330 * (1.0 - pow(pressure / seaLevelhPa, 0.1903));
return altitude;
}

158
examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/Adafruit_BMP280.h Normal file
View file

@ -0,0 +1,158 @@
/***************************************************************************
This is a library for the BMP280 pressure sensor
Designed specifically to work with the Adafruit BMP280 Breakout
----> http://www.adafruit.com/products/2651
These sensors use I2C to communicate, 2 pins are required to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#ifndef __BMP280_H__
#define __BMP280_H__
#if (ARDUINO >= 100)
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include <Adafruit_Sensor.h>
#ifdef __AVR_ATtiny85__
#include "TinyWireM.h"
#define Wire TinyWireM
#else
#include <Wire.h>
#endif
/*=========================================================================
I2C ADDRESS/BITS/SETTINGS
-----------------------------------------------------------------------*/
#define BMP280_ADDRESS (0x77)
#define BMP280_CHIPID (0x58)
/*=========================================================================*/
/*=========================================================================
REGISTERS
-----------------------------------------------------------------------*/
enum
{
BMP280_REGISTER_DIG_T1 = 0x88,
BMP280_REGISTER_DIG_T2 = 0x8A,
BMP280_REGISTER_DIG_T3 = 0x8C,
BMP280_REGISTER_DIG_P1 = 0x8E,
BMP280_REGISTER_DIG_P2 = 0x90,
BMP280_REGISTER_DIG_P3 = 0x92,
BMP280_REGISTER_DIG_P4 = 0x94,
BMP280_REGISTER_DIG_P5 = 0x96,
BMP280_REGISTER_DIG_P6 = 0x98,
BMP280_REGISTER_DIG_P7 = 0x9A,
BMP280_REGISTER_DIG_P8 = 0x9C,
BMP280_REGISTER_DIG_P9 = 0x9E,
BMP280_REGISTER_CHIPID = 0xD0,
BMP280_REGISTER_VERSION = 0xD1,
BMP280_REGISTER_SOFTRESET = 0xE0,
BMP280_REGISTER_CAL26 = 0xE1, // R calibration stored in 0xE1-0xF0
BMP280_REGISTER_CONTROL = 0xF4,
BMP280_REGISTER_CONFIG = 0xF5,
BMP280_REGISTER_PRESSUREDATA = 0xF7,
BMP280_REGISTER_TEMPDATA = 0xFA,
};
/*=========================================================================*/
/*=========================================================================
CALIBRATION DATA
-----------------------------------------------------------------------*/
typedef struct
{
uint16_t dig_T1;
int16_t dig_T2;
int16_t dig_T3;
uint16_t dig_P1;
int16_t dig_P2;
int16_t dig_P3;
int16_t dig_P4;
int16_t dig_P5;
int16_t dig_P6;
int16_t dig_P7;
int16_t dig_P8;
int16_t dig_P9;
uint8_t dig_H1;
int16_t dig_H2;
uint8_t dig_H3;
int16_t dig_H4;
int16_t dig_H5;
int8_t dig_H6;
} bmp280_calib_data;
/*=========================================================================*/
/*
class Adafruit_BMP280_Unified : public Adafruit_Sensor
{
public:
Adafruit_BMP280_Unified(int32_t sensorID = -1);
bool begin(uint8_t addr = BMP280_ADDRESS, uint8_t chipid = BMP280_CHIPID);
void getTemperature(float *temp);
void getPressure(float *pressure);
float pressureToAltitude(float seaLevel, float atmospheric, float temp);
float seaLevelForAltitude(float altitude, float atmospheric, float temp);
void getEvent(sensors_event_t*);
void getSensor(sensor_t*);
private:
uint8_t _i2c_addr;
int32_t _sensorID;
};
*/
class Adafruit_BMP280
{
public:
Adafruit_BMP280();
Adafruit_BMP280(int8_t cspin);
Adafruit_BMP280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
bool begin(uint8_t addr = BMP280_ADDRESS, uint8_t chipid = BMP280_CHIPID);
float readTemperature(void);
float readPressure(void);
float readAltitude(float seaLevelhPa = 1013.25);
private:
void readCoefficients(void);
uint8_t spixfer(uint8_t x);
void write8(byte reg, byte value);
uint8_t read8(byte reg);
uint16_t read16(byte reg);
uint32_t read24(byte reg);
int16_t readS16(byte reg);
uint16_t read16_LE(byte reg); // little endian
int16_t readS16_LE(byte reg); // little endian
uint8_t _i2caddr;
int32_t _sensorID;
int32_t t_fine;
int8_t _cs, _mosi, _miso, _sck;
bmp280_calib_data _bmp280_calib;
};
#endif

27
examples/osd/arduino-bmp280/Barometer_Sensor/README.md → examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/README.md
View file

@ -1,30 +1,17 @@
This is a library for the Adafruit BME280 Humidity, Barometric Pressure + Temp sensor
#Adafruit BMP280 Driver (Barometric Pressure Sensor) #
Designed specifically to work with the Adafruit BME280 Breakout
* http://www.adafruit.com/products/2652
This driver is for the Adafruit BMP280 Breakout (http://www.adafruit.com/products/2651)
These sensors use I2C or SPI to communicate, up to 4 pins are required to interface
## About the BMP280 ##
Use of this library also requires [Adafruit_Sensor](https://github.com/adafruit/Adafruit_Sensor)
to be installed on your local system.
This precision sensor from Bosch is the best low-cost sensing solution for measuring barometric pressure and temperature. Because pressure changes with altitude you can also use it as an altimeter!
Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!
## About this Driver ##
Check out the links above for our tutorials and wiring diagrams
Adafruit invests time and resources providing this open source code. Please support Adafruit and open-source hardware by purchasing products from Adafruit!
Written by Limor Fried/Ladyada for Adafruit Industries.
BSD license, all text above must be included in any redistribution
Written by Kevin (KTOWN) Townsend for Adafruit Industries.
To download. click the DOWNLOAD ZIP button, rename the uncompressed folder Adafruit_BME280.
Check that the Adafruit_BME280 folder contains Adafruit_BME280.cpp and Adafruit_BME280.h
Place the Adafruit_BME280 library folder your arduinosketchfolder/libraries/ folder.
You may need to create the libraries subfolder if its your first library. Restart the IDE.
We also have a great tutorial on Arduino library installation at:
http://learn.adafruit.com/adafruit-all-about-arduino-libraries-install-use
<!-- START COMPATIBILITY TABLE -->
## Compatibility

57
examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/examples/bmp280test/bmp280test.ino Normal file
View file

@ -0,0 +1,57 @@
/***************************************************************************
This is a library for the BMP280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BMEP280 Breakout
----> http://www.adafruit.com/products/2651
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BMP280.h>
#define BMP_SCK 13
#define BMP_MISO 12
#define BMP_MOSI 11
#define BMP_CS 10
Adafruit_BMP280 bme; // I2C
//Adafruit_BMP280 bme(BMP_CS); // hardware SPI
//Adafruit_BMP280 bme(BMP_CS, BMP_MOSI, BMP_MISO, BMP_SCK);
void setup() {
Serial.begin(9600);
Serial.println(F("BMP280 test"));
if (!bme.begin()) {
Serial.println(F("Could not find a valid BMP280 sensor, check wiring!"));
while (1);
}
}
void loop() {
Serial.print(F("Temperature = "));
Serial.print(bme.readTemperature());
Serial.println(" *C");
Serial.print(F("Pressure = "));
Serial.print(bme.readPressure());
Serial.println(" Pa");
Serial.print(F("Approx altitude = "));
Serial.print(bme.readAltitude(1013.25)); // this should be adjusted to your local forcase
Serial.println(" m");
Serial.println();
delay(2000);
}

9
examples/osd/arduino-bmp280/Adafruit_BMP280_Library-master/library.properties Normal file
View file

@ -0,0 +1,9 @@
name=Adafruit BMP280 Library
version=1.0.2
author=Adafruit
maintainer=Adafruit <info@adafruit.com>
sentence=Arduino library for BMP280 sensors.
paragraph=Arduino library for BMP280 pressure and altitude sensors.
category=Sensors
url=https://github.com/adafruit/Adafruit_BMP280_Library
architectures=*

502
examples/osd/arduino-bmp280/Barometer_Sensor/Adafruit_BME280.cpp
View file

@ -1,502 +0,0 @@
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include "Arduino.h"
#include <Wire.h>
#include <SPI.h>
#include "Adafruit_BME280.h"
/***************************************************************************
PRIVATE FUNCTIONS
***************************************************************************/
Adafruit_BME280::Adafruit_BME280()
: _cs(-1), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BME280::Adafruit_BME280(int8_t cspin)
: _cs(cspin), _mosi(-1), _miso(-1), _sck(-1)
{ }
Adafruit_BME280::Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin)
: _cs(cspin), _mosi(mosipin), _miso(misopin), _sck(sckpin)
{ }
/**************************************************************************/
/*!
@brief Initialise sensor with given parameters / settings
*/
/**************************************************************************/
bool Adafruit_BME280::begin(uint8_t addr)
{
_i2caddr = addr;
// init I2C or SPI sensor interface
if (_cs == -1) {
// I2C
Wire.begin();
} else {
digitalWrite(_cs, HIGH);
pinMode(_cs, OUTPUT);
if (_sck == -1) {
// hardware SPI
SPI.begin();
} else {
// software SPI
pinMode(_sck, OUTPUT);
pinMode(_mosi, OUTPUT);
pinMode(_miso, INPUT);
}
}
// check if sensor, i.e. the chip ID is correct
if (read8(BME280_REGISTER_CHIPID) != 0x60)
return false;
// reset the device using soft-reset
// this makes sure the IIR is off, etc.
write8(BME280_REGISTER_SOFTRESET, 0xB6);
// wait for chip to wake up.
delay(300);
// if chip is still reading calibration, delay
while (isReadingCalibration())
delay(100);
readCoefficients(); // read trimming parameters, see DS 4.2.2
setSampling(); // use defaults
return true;
}
/**************************************************************************/
/*!
@brief setup sensor with given parameters / settings
This is simply a overload to the normal begin()-function, so SPI users
don't get confused about the library requiring an address.
*/
/**************************************************************************/
void Adafruit_BME280::setSampling(sensor_mode mode,
sensor_sampling tempSampling,
sensor_sampling pressSampling,
sensor_sampling humSampling,
sensor_filter filter,
standby_duration duration) {
_measReg.mode = mode;
_measReg.osrs_t = tempSampling;
_measReg.osrs_p = pressSampling;
_humReg.osrs_h = humSampling;
_configReg.filter = filter;
_configReg.t_sb = duration;
// you must make sure to also set REGISTER_CONTROL after setting the
// CONTROLHUMID register, otherwise the values won't be applied (see DS 5.4.3)
write8(BME280_REGISTER_CONTROLHUMID, _humReg.get());
write8(BME280_REGISTER_CONFIG, _configReg.get());
write8(BME280_REGISTER_CONTROL, _measReg.get());
}
/**************************************************************************/
/*!
@brief Encapsulate hardware and software SPI transfer into one function
*/
/**************************************************************************/
uint8_t Adafruit_BME280::spixfer(uint8_t x) {
// hardware SPI
if (_sck == -1)
return SPI.transfer(x);
// software SPI
uint8_t reply = 0;
for (int i=7; i>=0; i--) {
reply <<= 1;
digitalWrite(_sck, LOW);
digitalWrite(_mosi, x & (1<<i));
digitalWrite(_sck, HIGH);
if (digitalRead(_miso))
reply |= 1;
}
return reply;
}
/**************************************************************************/
/*!
@brief Writes an 8 bit value over I2C or SPI
*/
/**************************************************************************/
void Adafruit_BME280::write8(byte reg, byte value) {
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.write((uint8_t)value);
Wire.endTransmission();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg & ~0x80); // write, bit 7 low
spixfer(value);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
}
/**************************************************************************/
/*!
@brief Reads an 8 bit value over I2C or SPI
*/
/**************************************************************************/
uint8_t Adafruit_BME280::read8(byte reg) {
uint8_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)1);
value = Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Reads a 16 bit value over I2C or SPI
*/
/**************************************************************************/
uint16_t Adafruit_BME280::read16(byte reg)
{
uint16_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)2);
value = (Wire.read() << 8) | Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = (spixfer(0) << 8) | spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
uint16_t Adafruit_BME280::read16_LE(byte reg) {
uint16_t temp = read16(reg);
return (temp >> 8) | (temp << 8);
}
/**************************************************************************/
/*!
@brief Reads a signed 16 bit value over I2C or SPI
*/
/**************************************************************************/
int16_t Adafruit_BME280::readS16(byte reg)
{
return (int16_t)read16(reg);
}
/**************************************************************************/
/*!
*/
/**************************************************************************/
int16_t Adafruit_BME280::readS16_LE(byte reg)
{
return (int16_t)read16_LE(reg);
}
/**************************************************************************/
/*!
@brief Reads a 24 bit value over I2C
*/
/**************************************************************************/
uint32_t Adafruit_BME280::read24(byte reg)
{
uint32_t value;
if (_cs == -1) {
Wire.beginTransmission((uint8_t)_i2caddr);
Wire.write((uint8_t)reg);
Wire.endTransmission();
Wire.requestFrom((uint8_t)_i2caddr, (byte)3);
value = Wire.read();
value <<= 8;
value |= Wire.read();
value <<= 8;
value |= Wire.read();
} else {
if (_sck == -1)
SPI.beginTransaction(SPISettings(500000, MSBFIRST, SPI_MODE0));
digitalWrite(_cs, LOW);
spixfer(reg | 0x80); // read, bit 7 high
value = spixfer(0);
value <<= 8;
value |= spixfer(0);
value <<= 8;
value |= spixfer(0);
digitalWrite(_cs, HIGH);
if (_sck == -1)
SPI.endTransaction(); // release the SPI bus
}
return value;
}
/**************************************************************************/
/*!
@brief Take a new measurement (only possible in forced mode)
*/
/**************************************************************************/
void Adafruit_BME280::takeForcedMeasurement()
{
// If we are in forced mode, the BME sensor goes back to sleep after each
// measurement and we need to set it to forced mode once at this point, so
// it will take the next measurement and then return to sleep again.
// In normal mode simply does new measurements periodically.
if (_measReg.mode == MODE_FORCED) {
// set to forced mode, i.e. "take next measurement"
write8(BME280_REGISTER_CONTROL, _measReg.get());
// wait until measurement has been completed, otherwise we would read
// the values from the last measurement
while (read8(BME280_REGISTER_STATUS) & 0x08)
delay(1);
}
}
/**************************************************************************/
/*!
@brief Reads the factory-set coefficients
*/
/**************************************************************************/
void Adafruit_BME280::readCoefficients(void)
{
_bme280_calib.dig_T1 = read16_LE(BME280_REGISTER_DIG_T1);
_bme280_calib.dig_T2 = readS16_LE(BME280_REGISTER_DIG_T2);
_bme280_calib.dig_T3 = readS16_LE(BME280_REGISTER_DIG_T3);
_bme280_calib.dig_P1 = read16_LE(BME280_REGISTER_DIG_P1);
_bme280_calib.dig_P2 = readS16_LE(BME280_REGISTER_DIG_P2);
_bme280_calib.dig_P3 = readS16_LE(BME280_REGISTER_DIG_P3);
_bme280_calib.dig_P4 = readS16_LE(BME280_REGISTER_DIG_P4);
_bme280_calib.dig_P5 = readS16_LE(BME280_REGISTER_DIG_P5);
_bme280_calib.dig_P6 = readS16_LE(BME280_REGISTER_DIG_P6);
_bme280_calib.dig_P7 = readS16_LE(BME280_REGISTER_DIG_P7);
_bme280_calib.dig_P8 = readS16_LE(BME280_REGISTER_DIG_P8);
_bme280_calib.dig_P9 = readS16_LE(BME280_REGISTER_DIG_P9);
_bme280_calib.dig_H1 = read8(BME280_REGISTER_DIG_H1);
_bme280_calib.dig_H2 = readS16_LE(BME280_REGISTER_DIG_H2);
_bme280_calib.dig_H3 = read8(BME280_REGISTER_DIG_H3);
_bme280_calib.dig_H4 = (read8(BME280_REGISTER_DIG_H4) << 4) | (read8(BME280_REGISTER_DIG_H4+1) & 0xF);
_bme280_calib.dig_H5 = (read8(BME280_REGISTER_DIG_H5+1) << 4) | (read8(BME280_REGISTER_DIG_H5) >> 4);
_bme280_calib.dig_H6 = (int8_t)read8(BME280_REGISTER_DIG_H6);
}
/**************************************************************************/
/*!
@brief return true if chip is busy reading cal data
*/
/**************************************************************************/
bool Adafruit_BME280::isReadingCalibration(void)
{
uint8_t const rStatus = read8(BME280_REGISTER_STATUS);
return (rStatus & (1 << 0)) != 0;
}
/**************************************************************************/
/*!
@brief Returns the temperature from the sensor
*/
/**************************************************************************/
float Adafruit_BME280::readTemperature(void)
{
int32_t var1, var2;
int32_t adc_T = read24(BME280_REGISTER_TEMPDATA);
if (adc_T == 0x800000) // value in case temp measurement was disabled
return NAN;
adc_T >>= 4;
var1 = ((((adc_T>>3) - ((int32_t)_bme280_calib.dig_T1 <<1))) *
((int32_t)_bme280_calib.dig_T2)) >> 11;
var2 = (((((adc_T>>4) - ((int32_t)_bme280_calib.dig_T1)) *
((adc_T>>4) - ((int32_t)_bme280_calib.dig_T1))) >> 12) *
((int32_t)_bme280_calib.dig_T3)) >> 14;
t_fine = var1 + var2;
float T = (t_fine * 5 + 128) >> 8;
return T/100;
}
/**************************************************************************/
/*!
@brief Returns the temperature from the sensor
*/
/**************************************************************************/
float Adafruit_BME280::readPressure(void) {
int64_t var1, var2, p;
readTemperature(); // must be done first to get t_fine
int32_t adc_P = read24(BME280_REGISTER_PRESSUREDATA);
if (adc_P == 0x800000) // value in case pressure measurement was disabled
return NAN;
adc_P >>= 4;
var1 = ((int64_t)t_fine) - 128000;
var2 = var1 * var1 * (int64_t)_bme280_calib.dig_P6;
var2 = var2 + ((var1*(int64_t)_bme280_calib.dig_P5)<<17);
var2 = var2 + (((int64_t)_bme280_calib.dig_P4)<<35);
var1 = ((var1 * var1 * (int64_t)_bme280_calib.dig_P3)>>8) +
((var1 * (int64_t)_bme280_calib.dig_P2)<<12);
var1 = (((((int64_t)1)<<47)+var1))*((int64_t)_bme280_calib.dig_P1)>>33;
if (var1 == 0) {
return 0; // avoid exception caused by division by zero
}
p = 1048576 - adc_P;
p = (((p<<31) - var2)*3125) / var1;
var1 = (((int64_t)_bme280_calib.dig_P9) * (p>>13) * (p>>13)) >> 25;
var2 = (((int64_t)_bme280_calib.dig_P8) * p) >> 19;
p = ((p + var1 + var2) >> 8) + (((int64_t)_bme280_calib.dig_P7)<<4);
return (float)p/256;
}
/**************************************************************************/
/*!
@brief Returns the humidity from the sensor
*/
/**************************************************************************/
float Adafruit_BME280::readHumidity(void) {
readTemperature(); // must be done first to get t_fine
int32_t adc_H = read16(BME280_REGISTER_HUMIDDATA);
if (adc_H == 0x8000) // value in case humidity measurement was disabled
return NAN;
int32_t v_x1_u32r;
v_x1_u32r = (t_fine - ((int32_t)76800));
v_x1_u32r = (((((adc_H << 14) - (((int32_t)_bme280_calib.dig_H4) << 20) -
(((int32_t)_bme280_calib.dig_H5) * v_x1_u32r)) + ((int32_t)16384)) >> 15) *
(((((((v_x1_u32r * ((int32_t)_bme280_calib.dig_H6)) >> 10) *
(((v_x1_u32r * ((int32_t)_bme280_calib.dig_H3)) >> 11) + ((int32_t)32768))) >> 10) +
((int32_t)2097152)) * ((int32_t)_bme280_calib.dig_H2) + 8192) >> 14));
v_x1_u32r = (v_x1_u32r - (((((v_x1_u32r >> 15) * (v_x1_u32r >> 15)) >> 7) *
((int32_t)_bme280_calib.dig_H1)) >> 4));
v_x1_u32r = (v_x1_u32r < 0) ? 0 : v_x1_u32r;
v_x1_u32r = (v_x1_u32r > 419430400) ? 419430400 : v_x1_u32r;
float h = (v_x1_u32r>>12);
return h / 1024.0;
}
/**************************************************************************/
/*!
Calculates the altitude (in meters) from the specified atmospheric
pressure (in hPa), and sea-level pressure (in hPa).
@param seaLevel Sea-level pressure in hPa
@param atmospheric Atmospheric pressure in hPa
*/
/**************************************************************************/
float Adafruit_BME280::readAltitude(float seaLevel)
{
// Equation taken from BMP180 datasheet (page 16):
// http://www.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
// Note that using the equation from wikipedia can give bad results
// at high altitude. See this thread for more information:
// http://forums.adafruit.com/viewtopic.php?f=22&t=58064
float atmospheric = readPressure() / 100.0F;
return 44330.0 * (1.0 - pow(atmospheric / seaLevel, 0.1903));
}
/**************************************************************************/
/*!
Calculates the pressure at sea level (in hPa) from the specified altitude
(in meters), and atmospheric pressure (in hPa).
@param altitude Altitude in meters
@param atmospheric Atmospheric pressure in hPa
*/
/**************************************************************************/
float Adafruit_BME280::seaLevelForAltitude(float altitude, float atmospheric)
{
// Equation taken from BMP180 datasheet (page 17):
// http://www.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
// Note that using the equation from wikipedia can give bad results
// at high altitude. See this thread for more information:
// http://forums.adafruit.com/viewtopic.php?f=22&t=58064
return atmospheric / pow(1.0 - (altitude/44330.0), 5.255);
}

295
examples/osd/arduino-bmp280/Barometer_Sensor/Adafruit_BME280.h
View file

@ -1,295 +0,0 @@
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#ifndef __BME280_H__
#define __BME280_H__
#if (ARDUINO >= 100)
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include <Adafruit_Sensor.h>
#include <Wire.h>
/*=========================================================================
I2C ADDRESS/BITS
-----------------------------------------------------------------------*/
#define BME280_ADDRESS (0x77)
/*=========================================================================*/
/*=========================================================================
REGISTERS
-----------------------------------------------------------------------*/
enum
{
BME280_REGISTER_DIG_T1 = 0x88,
BME280_REGISTER_DIG_T2 = 0x8A,
BME280_REGISTER_DIG_T3 = 0x8C,
BME280_REGISTER_DIG_P1 = 0x8E,
BME280_REGISTER_DIG_P2 = 0x90,
BME280_REGISTER_DIG_P3 = 0x92,
BME280_REGISTER_DIG_P4 = 0x94,
BME280_REGISTER_DIG_P5 = 0x96,
BME280_REGISTER_DIG_P6 = 0x98,
BME280_REGISTER_DIG_P7 = 0x9A,
BME280_REGISTER_DIG_P8 = 0x9C,
BME280_REGISTER_DIG_P9 = 0x9E,
BME280_REGISTER_DIG_H1 = 0xA1,
BME280_REGISTER_DIG_H2 = 0xE1,
BME280_REGISTER_DIG_H3 = 0xE3,
BME280_REGISTER_DIG_H4 = 0xE4,
BME280_REGISTER_DIG_H5 = 0xE5,
BME280_REGISTER_DIG_H6 = 0xE7,
BME280_REGISTER_CHIPID = 0xD0,
BME280_REGISTER_VERSION = 0xD1,
BME280_REGISTER_SOFTRESET = 0xE0,
BME280_REGISTER_CAL26 = 0xE1, // R calibration stored in 0xE1-0xF0
BME280_REGISTER_CONTROLHUMID = 0xF2,
BME280_REGISTER_STATUS = 0XF3,
BME280_REGISTER_CONTROL = 0xF4,
BME280_REGISTER_CONFIG = 0xF5,
BME280_REGISTER_PRESSUREDATA = 0xF7,
BME280_REGISTER_TEMPDATA = 0xFA,
BME280_REGISTER_HUMIDDATA = 0xFD
};
/*=========================================================================*/
/*=========================================================================
CALIBRATION DATA
-----------------------------------------------------------------------*/
typedef struct
{
uint16_t dig_T1;
int16_t dig_T2;
int16_t dig_T3;
uint16_t dig_P1;
int16_t dig_P2;
int16_t dig_P3;
int16_t dig_P4;
int16_t dig_P5;
int16_t dig_P6;
int16_t dig_P7;
int16_t dig_P8;
int16_t dig_P9;
uint8_t dig_H1;
int16_t dig_H2;
uint8_t dig_H3;
int16_t dig_H4;
int16_t dig_H5;
int8_t dig_H6;
} bme280_calib_data;
/*=========================================================================*/
/*
class Adafruit_BME280_Unified : public Adafruit_Sensor
{
public:
Adafruit_BME280_Unified(int32_t sensorID = -1);
bool begin(uint8_t addr = BME280_ADDRESS);
void getTemperature(float *temp);
void getPressure(float *pressure);
float pressureToAltitude(float seaLevel, float atmospheric, float temp);
float seaLevelForAltitude(float altitude, float atmospheric, float temp);
void getEvent(sensors_event_t*);
void getSensor(sensor_t*);
private:
uint8_t _i2c_addr;
int32_t _sensorID;
};
*/
class Adafruit_BME280 {
public:
enum sensor_sampling {
SAMPLING_NONE = 0b000,
SAMPLING_X1 = 0b001,
SAMPLING_X2 = 0b010,
SAMPLING_X4 = 0b011,
SAMPLING_X8 = 0b100,
SAMPLING_X16 = 0b101
};
enum sensor_mode {
MODE_SLEEP = 0b00,
MODE_FORCED = 0b01,
MODE_NORMAL = 0b11
};
enum sensor_filter {
FILTER_OFF = 0b000,
FILTER_X2 = 0b001,
FILTER_X4 = 0b010,
FILTER_X8 = 0b011,
FILTER_X16 = 0b100
};
// standby durations in ms
enum standby_duration {
STANDBY_MS_0_5 = 0b000,
STANDBY_MS_10 = 0b110,
STANDBY_MS_20 = 0b111,
STANDBY_MS_62_5 = 0b001,
STANDBY_MS_125 = 0b010,
STANDBY_MS_250 = 0b011,
STANDBY_MS_500 = 0b100,
STANDBY_MS_1000 = 0b101
};
// constructors
Adafruit_BME280(void);
Adafruit_BME280(int8_t cspin);
Adafruit_BME280(int8_t cspin, int8_t mosipin, int8_t misopin, int8_t sckpin);
bool begin(uint8_t addr = BME280_ADDRESS);
void setSampling(sensor_mode mode = MODE_NORMAL,
sensor_sampling tempSampling = SAMPLING_X16,
sensor_sampling pressSampling = SAMPLING_X16,
sensor_sampling humSampling = SAMPLING_X16,
sensor_filter filter = FILTER_OFF,
standby_duration duration = STANDBY_MS_0_5
);
void takeForcedMeasurement();
float readTemperature(void);
float readPressure(void);
float readHumidity(void);
float readAltitude(float seaLevel);
float seaLevelForAltitude(float altitude, float pressure);
private:
void readCoefficients(void);
bool isReadingCalibration(void);
uint8_t spixfer(uint8_t x);
void write8(byte reg, byte value);
uint8_t read8(byte reg);
uint16_t read16(byte reg);
uint32_t read24(byte reg);
int16_t readS16(byte reg);
uint16_t read16_LE(byte reg); // little endian
int16_t readS16_LE(byte reg); // little endian
uint8_t _i2caddr;
int32_t _sensorID;
int32_t t_fine;
int8_t _cs, _mosi, _miso, _sck;
bme280_calib_data _bme280_calib;
// The config register
struct config {
// inactive duration (standby time) in normal mode
// 000 = 0.5 ms
// 001 = 62.5 ms
// 010 = 125 ms
// 011 = 250 ms
// 100 = 500 ms
// 101 = 1000 ms
// 110 = 10 ms
// 111 = 20 ms
unsigned int t_sb : 3;
// filter settings
// 000 = filter off
// 001 = 2x filter
// 010 = 4x filter
// 011 = 8x filter
// 100 and above = 16x filter
unsigned int filter : 3;
// unused - don't set
unsigned int none : 1;
unsigned int spi3w_en : 1;
unsigned int get() {
return (t_sb << 5) | (filter << 3) | spi3w_en;
}
};
config _configReg;
// The ctrl_meas register
struct ctrl_meas {
// temperature oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_t : 3;
// pressure oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_p : 3;
// device mode
// 00 = sleep
// 01 or 10 = forced
// 11 = normal
unsigned int mode : 2;
unsigned int get() {
return (osrs_t << 5) | (osrs_p << 3) | mode;
}
};
ctrl_meas _measReg;
// The ctrl_hum register
struct ctrl_hum {
// unused - don't set
unsigned int none : 5;
// pressure oversampling
// 000 = skipped
// 001 = x1
// 010 = x2
// 011 = x4
// 100 = x8
// 101 and above = x16
unsigned int osrs_h : 3;
unsigned int get() {
return (osrs_h);
}
};
ctrl_hum _humReg;
};
#endif

157
examples/osd/arduino-bmp280/Barometer_Sensor/examples/advancedsettings/advancedsettings.ino
View file

@ -1,157 +0,0 @@
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface. The device's I2C address is either 0x76 or 0x77.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
#define BME_SCK 13
#define BME_MISO 12
#define BME_MOSI 11
#define BME_CS 10
#define SEALEVELPRESSURE_HPA (1013.25)
Adafruit_BME280 bme; // I2C
//Adafruit_BME280 bme(BME_CS); // hardware SPI
//Adafruit_BME280 bme(BME_CS, BME_MOSI, BME_MISO, BME_SCK); // software SPI
unsigned long delayTime;
void setup() {
Serial.begin(9600);
Serial.println(F("BME280 test"));
if (! bme.begin()) {
Serial.println("Could not find a valid BME280 sensor, check wiring!");
while (1);
}
Serial.println("-- Default Test --");
Serial.println("normal mode, 16x oversampling for all, filter off,");
Serial.println("0.5ms standby period");
delayTime = 5000;
// For more details on the following scenarious, see chapter
// 3.5 "Recommended modes of operation" in the datasheet
/*
// weather monitoring
Serial.println("-- Weather Station Scenario --");
Serial.println("forced mode, 1x temperature / 1x humidity / 1x pressure oversampling,");
Serial.println("filter off");
bme.setSampling(Adafruit_BME280::MODE_FORCED,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_X1, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_OFF );
// suggested rate is 1/60Hz (1m)
delayTime = 60000; // in milliseconds
*/
/*
// humidity sensing
Serial.println("-- Humidity Sensing Scenario --");
Serial.println("forced mode, 1x temperature / 1x humidity / 0x pressure oversampling");
Serial.println("= pressure off, filter off");
bme.setSampling(Adafruit_BME280::MODE_FORCED,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_NONE, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_OFF );
// suggested rate is 1Hz (1s)
delayTime = 1000; // in milliseconds
*/
/*
// indoor navigation
Serial.println("-- Indoor Navigation Scenario --");
Serial.println("normal mode, 16x pressure / 2x temperature / 1x humidity oversampling,");
Serial.println("0.5ms standby period, filter 16x");
bme.setSampling(Adafruit_BME280::MODE_NORMAL,
Adafruit_BME280::SAMPLING_X2, // temperature
Adafruit_BME280::SAMPLING_X16, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_X16,
Adafruit_BME280::STANDBY_MS_0_5 );
// suggested rate is 25Hz
// 1 + (2 * T_ovs) + (2 * P_ovs + 0.5) + (2 * H_ovs + 0.5)
// T_ovs = 2
// P_ovs = 16
// H_ovs = 1
// = 40ms (25Hz)
// with standby time that should really be 24.16913... Hz
delayTime = 41;
/*
// gaming
Serial.println("-- Gaming Scenario --");
Serial.println("normal mode, 4x pressure / 1x temperature / 0x humidity oversampling,");
Serial.println("= humidity off, 0.5ms standby period, filter 16x");
bme.setSampling(Adafruit_BME280::MODE_NORMAL,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_X4, // pressure
Adafruit_BME280::SAMPLING_NONE, // humidity
Adafruit_BME280::FILTER_X16,
Adafruit_BME280::STANDBY_MS_0_5 );
// Suggested rate is 83Hz
// 1 + (2 * T_ovs) + (2 * P_ovs + 0.5)
// T_ovs = 1
// P_ovs = 4
// = 11.5ms + 0.5ms standby
delayTime = 12;
*/
Serial.println();
}
void loop() {
// Only needed in forced mode! In normal mode, you can remove the next line.
bme.takeForcedMeasurement(); // has no effect in normal mode
printValues();
delay(delayTime);
}
void printValues() {
Serial.print("Temperature = ");
Serial.print(bme.readTemperature());
Serial.println(" *C");
Serial.print("Pressure = ");
Serial.print(bme.readPressure() / 100.0F);
Serial.println(" hPa");
Serial.print("Approx. Altitude = ");
Serial.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
Serial.println(" m");
Serial.print("Humidity = ");
Serial.print(bme.readHumidity());
Serial.println(" %");
Serial.println();
}

81
examples/osd/arduino-bmp280/Barometer_Sensor/examples/bme280test/bme280test.ino
View file

@ -1,81 +0,0 @@
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface. The device's I2C address is either 0x76 or 0x77.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
#define BME_SCK 13
#define BME_MISO 12
#define BME_MOSI 11
#define BME_CS 10
#define SEALEVELPRESSURE_HPA (1013.25)
Adafruit_BME280 bme; // I2C
//Adafruit_BME280 bme(BME_CS); // hardware SPI
//Adafruit_BME280 bme(BME_CS, BME_MOSI, BME_MISO, BME_SCK); // software SPI
unsigned long delayTime;
void setup() {
Serial.begin(9600);
Serial.println(F("BME280 test"));
bool status;
// default settings
status = bme.begin();
if (!status) {
Serial.println("Could not find a valid BME280 sensor, check wiring!");
while (1);
}
Serial.println("-- Default Test --");
delayTime = 1000;
Serial.println();
}
void loop() {
printValues();
delay(delayTime);
}
void printValues() {
Serial.print("Temperature = ");
Serial.print(bme.readTemperature());
Serial.println(" *C");
Serial.print("Pressure = ");
Serial.print(bme.readPressure() / 100.0F);
Serial.println(" hPa");
Serial.print("Approx. Altitude = ");
Serial.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
Serial.println(" m");
Serial.print("Humidity = ");
Serial.print(bme.readHumidity());
Serial.println(" %");
Serial.println();
}

2
examples/osd/arduino-bmp280/Makefile
View file

@ -12,7 +12,7 @@ CONTIKI_WITH_IPV6 = 1
CFLAGS += -DPROJECT_CONF_H=\"project-conf.h\"
LFLAGS += -lm
PROJECT_SOURCEFILES += ${SKETCH}.cpp Adafruit_BME280.cpp
PROJECT_SOURCEFILES += ${SKETCH}.cpp Adafruit_BMP280.cpp
# automatically build RESTful resources
REST_RESOURCES_DIR = ./resources

17
examples/osd/arduino-bmp280/sketch.pde
View file

@ -12,7 +12,7 @@
#include <Wire.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
#include <Adafruit_BMP280.h>
extern "C" {
#include "arduino-process.h"
@ -26,13 +26,13 @@ float bmpatm;
float bmpalt;
float bmphum;
char bmptemp_s[8];
char bmppress_s[8];
char bmppress_s[10];
char bmpatm_s[8];
char bmpalt_s[8];
char bmphum_s[8];
#define SEALEVELPRESSURE_HPA (1013.25)
Adafruit_BME280 bme; // I2C
Adafruit_BMP280 bme; // I2C
#define LED_PIN 4
}
@ -46,9 +46,9 @@ void setup (void)
bool status;
// default settings
status = bme.begin(0x77);
status = bme.begin(0x76);
if (!status) {
printf("Could not find a valid BME280 sensor, check wiring!");
printf("Could not find a valid BMP280 sensor, check wiring!");
}
// init coap resourcen
rest_init_engine ();
@ -69,13 +69,12 @@ void loop (void)
bmppress = bme.readPressure();
bmpalt = bme.readAltitude(SEALEVELPRESSURE_HPA);
bmpatm = bme.readPressure() / 100.0F;
bmphum = bme.readHumidity();
dtostrf(bmptemp , 6, 2, bmptemp_s );
dtostrf(bmppress , 6, 2, bmppress_s );
dtostrf(bmpalt , 6, 2, bmpalt_s );
dtostrf(bmpatm , 6, 2, bmpatm_s );
dtostrf(bmphum , 6, 2, bmphum_s );
// remove space
if(bmptemp_s[0]==' '){
@ -90,14 +89,10 @@ void loop (void)
if(bmpatm_s[0]==' '){
memcpy (bmpatm_s,bmpatm_s+1,strlen(bmpatm_s)+1);
}
if(bmphum_s[0]==' '){
memcpy (bmphum_s,bmphum_s+1,strlen(bmphum_s)+1);
}
// Debug Print
printf("Temp: %s\n",bmptemp_s);
printf("Press: %s\n",bmppress_s);
printf("Altitude: %s\n",bmpalt_s);
printf("atm: %s\n",bmpatm_s);
printf("hum: %s\n",bmphum_s);
}