osd-contiki/cpu/stm32w108/hal/micro/micro-common.h

117 lines
3.7 KiB
C
Raw Normal View History

2010-10-25 11:03:38 +02:00
/** @file micro-common.h
* @brief Minimal Hal functions common across all microcontroller-specific files.
* See @ref micro for documentation.
*
* <!--(C) COPYRIGHT 2010 STMicroelectronics. All rights reserved. -->
*/
/** @addtogroup micro
* Many of the supplied example applications use these microcontroller functions.
* See hal/micro/micro-common.h for source code.
*
*@{
*/
#ifndef __MICRO_COMMON_H__
#define __MICRO_COMMON_H__
/** @brief Initializes microcontroller-specific peripherals.
*/
void halInit(void);
/** @brief Restarts the microcontroller and therefore everything else.
*/
void halReboot(void);
/** @brief Powers up microcontroller peripherals and board peripherals.
*/
void halPowerUp(void);
/** @brief Powers down microcontroller peripherals and board peripherals.
*/
void halPowerDown(void);
/** @brief The value that must be passed as the single parameter to
* ::halInternalDisableWatchDog() in order to sucessfully disable the watchdog
* timer.
*/
#define MICRO_DISABLE_WATCH_DOG_KEY 0xA5
/** @brief Enables the watchdog timer.
*/
void halInternalEnableWatchDog(void);
/** @brief Disables the watchdog timer.
*
* @note To prevent the watchdog from being disabled accidentally,
* a magic key must be provided.
*
* @param magicKey A value (::MICRO_DISABLE_WATCH_DOG_KEY) that enables the function.
*/
void halInternalDisableWatchDog(int8u magicKey);
/** @brief Determines whether the watchdog has been enabled or disabled.
*
* @return A boolean value indicating if the watchdog is current enabled.
*/
boolean halInternalWatchDogEnabled( void );
#ifdef DOXYGEN_SHOULD_SKIP_THIS
/** @brief Enumerations for the possible microcontroller sleep modes.
* - SLEEPMODE_RUNNING
* Everything is active and running. In practice this mode is not
* used, but it is defined for completeness of information.
* - SLEEPMODE_IDLE
* Only the CPU is idled. The rest of the chip continues runing
* normally. The chip will wake from any interrupt.
* - SLEEPMODE_WAKETIMER
* The sleep timer clock sources remain running. The RC is always
* running and the 32kHz XTAL depends on the board header. Wakeup
* is possible from both GPIO and the sleep timer. System time
* is maintained. The sleep timer is assumed to be configured
* properly for wake events.
* - SLEEPMODE_MAINTAINTIMER
* The sleep timer clock sources remain running. The RC is always
* running and the 32kHz XTAL depends on the board header. Wakeup
* is possible from only GPIO. System time is maintained.
* - SLEEPMODE_NOTIMER
* The sleep timer clock sources (both RC and XTAL) are turned off.
* Wakeup is possible from only GPIO. System time is lost.
*/
enum SleepModes
#else
typedef int8u SleepModes;
enum
#endif
{
SLEEPMODE_RUNNING = 0,
SLEEPMODE_IDLE = 1,
SLEEPMODE_WAKETIMER = 2,
SLEEPMODE_MAINTAINTIMER = 3,
SLEEPMODE_NOTIMER = 4,
};
/** @brief Blocks the current thread of execution for the specified
* amount of time, in microseconds.
*
* The function is implemented with cycle-counted busy loops
* and is intended to create the short delays required when interfacing with
* hardware peripherals.
*
* The accuracy of the timing provided by this function is not specified,
* but a general rule is that when running off of a crystal oscillator it will
* be within 10us. If the micro is running off of another type of oscillator
* (e.g. RC) the timing accuracy will potentially be much worse.
*
* @param us The specified time, in microseconds.
Values should be between 1 and 65535 microseconds.
*/
void halCommonDelayMicroseconds(int16u us);
#endif //__MICRO_COMMON_H__
/** @} END micro group */