2015-08-16 17:30:04 +02:00
/******************************************************************************
* Filename : common_cmd . h
* Revised : 2015 - 08 - 04 10 : 40 : 45 + 0200 ( Tue , 04 Aug 2015 )
* Revision : 44326
*
* Description : CC13xx API for common / generic commands
*
* Copyright ( c ) 2015 , Texas Instruments Incorporated
* All rights reserved .
*
* Redistribution and use in source and binary forms , with or without
* modification , are permitted provided that the following conditions are met :
*
* 1 ) Redistributions of source code must retain the above copyright notice ,
* this list of conditions and the following disclaimer .
*
* 2 ) Redistributions in binary form must reproduce the above copyright notice ,
* this list of conditions and the following disclaimer in the documentation
* and / or other materials provided with the distribution .
*
* 3 ) Neither the name of the ORGANIZATION nor the names of its contributors may
* be used to endorse or promote products derived from this software without
* specific prior written permission .
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS " AS IS "
* AND ANY EXPRESS OR IMPLIED WARRANTIES , INCLUDING , BUT NOT LIMITED TO , THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED . IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT , INDIRECT , INCIDENTAL , SPECIAL , EXEMPLARY , OR
* CONSEQUENTIAL DAMAGES ( INCLUDING , BUT NOT LIMITED TO , PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES ; LOSS OF USE , DATA , OR PROFITS ; OR BUSINESS
* INTERRUPTION ) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY , WHETHER IN
* CONTRACT , STRICT LIABILITY , OR TORT ( INCLUDING NEGLIGENCE OR OTHERWISE )
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE , EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE .
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
# ifndef COMMON_CMD_H_
# define COMMON_CMD_H_
# ifndef __RFC_STRUCT
# ifdef __GNUC__
# define __RFC_STRUCT __attribute__ ((aligned (4)))
# else
# define __RFC_STRUCT
# endif
# endif
//! \addtogroup rfc
//! @{
//! \addtogroup common_cmd
//! @{
# include <stdint.h>
# include "mailbox.h"
typedef struct __RFC_STRUCT rfc_command_s rfc_command_t ;
typedef struct __RFC_STRUCT rfc_radioOp_s rfc_radioOp_t ;
typedef struct __RFC_STRUCT rfc_CMD_NOP_s rfc_CMD_NOP_t ;
typedef struct __RFC_STRUCT rfc_CMD_RADIO_SETUP_s rfc_CMD_RADIO_SETUP_t ;
typedef struct __RFC_STRUCT rfc_CMD_FS_s rfc_CMD_FS_t ;
typedef struct __RFC_STRUCT rfc_CMD_FS_OFF_s rfc_CMD_FS_OFF_t ;
typedef struct __RFC_STRUCT rfc_CMD_RX_s rfc_CMD_RX_t ;
typedef struct __RFC_STRUCT rfc_CMD_TX_s rfc_CMD_TX_t ;
typedef struct __RFC_STRUCT rfc_CMD_RX_TEST_s rfc_CMD_RX_TEST_t ;
typedef struct __RFC_STRUCT rfc_CMD_TX_TEST_s rfc_CMD_TX_TEST_t ;
typedef struct __RFC_STRUCT rfc_CMD_SYNC_STOP_RAT_s rfc_CMD_SYNC_STOP_RAT_t ;
typedef struct __RFC_STRUCT rfc_CMD_SYNC_START_RAT_s rfc_CMD_SYNC_START_RAT_t ;
typedef struct __RFC_STRUCT rfc_CMD_COUNT_s rfc_CMD_COUNT_t ;
typedef struct __RFC_STRUCT rfc_CMD_FS_POWERUP_s rfc_CMD_FS_POWERUP_t ;
typedef struct __RFC_STRUCT rfc_CMD_FS_POWERDOWN_s rfc_CMD_FS_POWERDOWN_t ;
typedef struct __RFC_STRUCT rfc_CMD_SCH_IMM_s rfc_CMD_SCH_IMM_t ;
typedef struct __RFC_STRUCT rfc_CMD_COUNT_BRANCH_s rfc_CMD_COUNT_BRANCH_t ;
typedef struct __RFC_STRUCT rfc_CMD_PATTERN_CHECK_s rfc_CMD_PATTERN_CHECK_t ;
typedef struct __RFC_STRUCT rfc_CMD_TX_POWER_BOOST_s rfc_CMD_TX_POWER_BOOST_t ;
typedef struct __RFC_STRUCT rfc_CMD_ABORT_s rfc_CMD_ABORT_t ;
typedef struct __RFC_STRUCT rfc_CMD_STOP_s rfc_CMD_STOP_t ;
typedef struct __RFC_STRUCT rfc_CMD_GET_RSSI_s rfc_CMD_GET_RSSI_t ;
typedef struct __RFC_STRUCT rfc_CMD_UPDATE_RADIO_SETUP_s rfc_CMD_UPDATE_RADIO_SETUP_t ;
typedef struct __RFC_STRUCT rfc_CMD_TRIGGER_s rfc_CMD_TRIGGER_t ;
typedef struct __RFC_STRUCT rfc_CMD_GET_FW_INFO_s rfc_CMD_GET_FW_INFO_t ;
typedef struct __RFC_STRUCT rfc_CMD_START_RAT_s rfc_CMD_START_RAT_t ;
typedef struct __RFC_STRUCT rfc_CMD_PING_s rfc_CMD_PING_t ;
typedef struct __RFC_STRUCT rfc_CMD_ADD_DATA_ENTRY_s rfc_CMD_ADD_DATA_ENTRY_t ;
typedef struct __RFC_STRUCT rfc_CMD_REMOVE_DATA_ENTRY_s rfc_CMD_REMOVE_DATA_ENTRY_t ;
typedef struct __RFC_STRUCT rfc_CMD_FLUSH_QUEUE_s rfc_CMD_FLUSH_QUEUE_t ;
typedef struct __RFC_STRUCT rfc_CMD_CLEAR_RX_s rfc_CMD_CLEAR_RX_t ;
typedef struct __RFC_STRUCT rfc_CMD_REMOVE_PENDING_ENTRIES_s rfc_CMD_REMOVE_PENDING_ENTRIES_t ;
typedef struct __RFC_STRUCT rfc_CMD_SET_RAT_CMP_s rfc_CMD_SET_RAT_CMP_t ;
typedef struct __RFC_STRUCT rfc_CMD_SET_RAT_CPT_s rfc_CMD_SET_RAT_CPT_t ;
typedef struct __RFC_STRUCT rfc_CMD_DISABLE_RAT_CH_s rfc_CMD_DISABLE_RAT_CH_t ;
typedef struct __RFC_STRUCT rfc_CMD_SET_RAT_OUTPUT_s rfc_CMD_SET_RAT_OUTPUT_t ;
typedef struct __RFC_STRUCT rfc_CMD_ARM_RAT_CH_s rfc_CMD_ARM_RAT_CH_t ;
typedef struct __RFC_STRUCT rfc_CMD_DISARM_RAT_CH_s rfc_CMD_DISARM_RAT_CH_t ;
typedef struct __RFC_STRUCT rfc_CMD_SET_TX_POWER_s rfc_CMD_SET_TX_POWER_t ;
typedef struct __RFC_STRUCT rfc_CMD_UPDATE_FS_s rfc_CMD_UPDATE_FS_t ;
typedef struct __RFC_STRUCT rfc_CMD_BUS_REQUEST_s rfc_CMD_BUS_REQUEST_t ;
//! \addtogroup command
//! @{
struct __RFC_STRUCT rfc_command_s {
uint16_t commandNo ; //!< The command ID number
} ;
//! @}
//! \addtogroup radioOp
//! @{
//! Common definition for radio operation commands
struct __RFC_STRUCT rfc_radioOp_s {
uint16_t commandNo ; //!< The command ID number
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
} ;
//! @}
//! \addtogroup CMD_NOP
//! @{
# define CMD_NOP 0x0801
struct __RFC_STRUCT rfc_CMD_NOP_s {
uint16_t commandNo ; //!< The command ID number 0x0801
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
} ;
//! @}
//! \addtogroup CMD_RADIO_SETUP
//! @{
# define CMD_RADIO_SETUP 0x0802
struct __RFC_STRUCT rfc_CMD_RADIO_SETUP_s {
uint16_t commandNo ; //!< The command ID number 0x0802
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint8_t mode ; //!< \brief The main mode to use<br>
//!< 0x00: BLE<br>
//!< 0x01: IEEE 802.15.4<br>
//!< 0x02: 2 Mbps GFSK<br>
//!< 0x05: 5 Mbps coded 8-FSK<br>
//!< 0x06: ANT<br>
//!< 0xFF: Keep existing mode; update overrides only<br>
//!< Others: <i>Reserved</i>
uint8_t loDivider ; //!< \brief LO divider setting to use. Supported values: 0 (equivalent to 2), 2, 5, 6, 10, 12, 15,
//!< and 30.<br>
//!< Value of 0 or 2 only supported for devices that support 2.4 GHz operation
struct {
uint16_t frontEndMode : 3 ; //!< \brief 0x00: Differential mode<br>
//!< 0x01: Single-ended mode RFP<br>
//!< 0x02: Single-ended mode RFN<br>
//!< 0x05 Single-ended mode RFP with external frontend control on RF pins (RFN and RXTX)<br>
//!< 0x06 Single-ended mode RFN with external frontend control on RF pins (RFP and RXTX)<br>
//!< Others: <i>Reserved</i>
uint16_t biasMode : 1 ; //!< \brief 0: Internal bias<br>
//!< 1: External bias
uint16_t : 6 ;
uint16_t bNoFsPowerUp : 1 ; //!< \brief 0: Power up frequency synth<br>
//!< 1: Do not power up frequency synth
} config ; //!< Configuration options
struct {
uint16_t IB : 6 ; //!< Value to write to the PA power control field at 25 °C
uint16_t GC : 2 ; //!< Value to write to the gain control of the 1st stage of the PA
uint16_t boost : 1 ; //!< Value of boost bit in synth
uint16_t tempCoeff : 7 ; //!< Temperature coefficient for IB. 0: No temperature compensation
} txPower ; //!< Transmit power
uint32_t * pRegOverride ; //!< \brief Pointer to a list of hardware and configuration registers to override. If NULL, no
//!< override is used.
} ;
//! @}
//! \addtogroup CMD_FS
//! @{
# define CMD_FS 0x0803
struct __RFC_STRUCT rfc_CMD_FS_s {
uint16_t commandNo ; //!< The command ID number 0x0803
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t frequency ; //!< The frequency in MHz to tune to
uint16_t fractFreq ; //!< Fractional part of the frequency to tune to
struct {
uint8_t bTxMode : 1 ; //!< \brief 0: Start synth in Rx mode<br>
//!< 1: Start synth in Tx mode
uint8_t refFreq : 6 ; //!< \brief 0: Use default reference frequency<br>
//!< Others: Use reference frequency 24 MHz/<code>refFreq</code>
} synthConf ;
uint8_t __dummy0 ;
uint8_t midPrecal ; //!< Mid pre-calibration value to use when <code>bOverrideCalib</code> and <code>bSkipCoarseCalib</code> are both 1
uint8_t ktPrecal ; //!< KT pre-calibration value to use when <code>bOverrideCalib</code> and <code>bSkipCoarseCalib</code> are both 1
uint16_t tdcPrecal ; //!< TDC pre-calibration value to use when <code>bOverrideCalib</code> and <code>bSkipCoarseCalib</code> are both 1
} ;
//! @}
//! \addtogroup CMD_FS_OFF
//! @{
# define CMD_FS_OFF 0x0804
struct __RFC_STRUCT rfc_CMD_FS_OFF_s {
uint16_t commandNo ; //!< The command ID number 0x0804
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
} ;
//! @}
//! \addtogroup CMD_RX
//! @{
# define CMD_RX 0x0805
struct __RFC_STRUCT rfc_CMD_RX_s {
uint16_t commandNo ; //!< The command ID number 0x0805
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
struct {
uint16_t endianness : 1 ; //!< \brief 0: Least significant bit first<br>
//!< 1: Most significant bit first
uint16_t numHdrBits : 6 ; //!< Number of bits in the header
uint16_t bFsOff : 1 ; //!< \brief 0: Keep frequency synth on after command<br>
//!< 1: Turn frequency synth off after command
uint16_t bUseCrc : 1 ; //!< \brief 0: No CRC<br>
//!< 1: The last bytes of the packet are a CRC
uint16_t bCrcIncSw : 1 ; //!< \brief 0: Do not include sync word in CRC calculation<br>
//!< 1: Include sync word in CRC calculation
uint16_t bCrcIncHdr : 1 ; //!< \brief 0: Do not include header in CRC calculation<br>
//!< 1: Include header in CRC calculation
uint16_t bReportCrc : 1 ; //!< \brief 0: Do not write CRC to receive buffer<br>
//!< 1: Write received CRC to receive buffer
uint16_t endType : 1 ; //!< \brief 0: Packet is received to the end if end trigger happens after sync is obtained<br>
//!< 1: Packet reception is stopped if end trigger happens
uint16_t bDualSw : 1 ; //!< \brief 0: Single sync word<br>
//!< 1: Dual sync word.
} pktConfig ;
uint32_t syncWord ; //!< Sync word to receive
uint32_t syncWord2 ; //!< Secondary sync word to receive if <code>pktConfig.bDualSw</code> = 1
struct {
uint16_t numLenBits : 4 ; //!< Number of bits in the length field
uint16_t lenFieldPos : 5 ; //!< Bit position of the first bit in the length field
uint16_t lenOffset : 7 ; //!< Signed number to add to the received length field
} lenConfig ;
uint16_t maxLen ; //!< Maximum number of bytes in the received packet (including header, excluding CRC)
uint8_t * pRecPkt ; //!< Pointer to buffer for received packet. NULL: Do not store the contents.
ratmr_t endTime ; //!< Time to end the operation
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} endTrigger ; //!< Trigger classifier for ending the operation
int8_t rssi ; //!< RSSI of received packet
uint16_t recLen ; //!< Number of bytes written to receive buffer
ratmr_t timeStamp ; //!< Time stamp of received packet
uint16_t nRxOk ; //!< Counter of number of received packets with CRC OK and first sync word
uint16_t nRxNok ; //!< Counter of number of received packets with CRC error and first sync word
uint16_t nRx2Ok ; //!< \brief Counter of number of received packets with CRC OK and second sync word; may safely be
//!< omitted if <code>pktConfig.bDualSw</code> is 0
uint16_t nRx2Nok ; //!< \brief Counter of number of received packets with CRC error and second sync word; may safely be
//!< omitted if <code>pktConfig.bDualSw</code> is 0
} ;
//! @}
//! \addtogroup CMD_TX
//! @{
# define CMD_TX 0x0806
struct __RFC_STRUCT rfc_CMD_TX_s {
uint16_t commandNo ; //!< The command ID number 0x0806
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
struct {
uint16_t endianness : 1 ; //!< \brief 0: Least significant bit first<br>
//!< 1: Most significant bit first
uint16_t numHdrBits : 6 ; //!< Number of bits in the header
uint16_t bFsOff : 1 ; //!< \brief 0: Keep frequency synth on after command<br>
//!< 1: Turn frequency synth off after command
uint16_t bUseCrc : 1 ; //!< \brief 0: No CRC<br>
//!< 1: Append a CRC to the packet
uint16_t bCrcIncSw : 1 ; //!< \brief 0: Do not include sync word in CRC calculation<br>
//!< 1: Include sync word in CRC calculation
uint16_t bCrcIncHdr : 1 ; //!< \brief 0: Do not include header in CRC calculation<br>
//!< 1: Include header in CRC calculation
} pktConfig ;
uint32_t syncWord ; //!< Sync word to transmit
uint8_t * pTxPkt ; //!< Pointer to buffer for transmitted packet.
uint16_t pktLen ; //!< Number of bytes in the transmitted packet
} ;
//! @}
//! \addtogroup CMD_RX_TEST
//! @{
# define CMD_RX_TEST 0x0807
struct __RFC_STRUCT rfc_CMD_RX_TEST_s {
uint16_t commandNo ; //!< The command ID number 0x0807
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
struct {
uint8_t bEnaFifo : 1 ; //!< \brief 0: Do not enable FIFO in modem, so that received data is not available<br>
//!< 1: Enable FIFO in modem – the data must be read out by the application
uint8_t bFsOff : 1 ; //!< \brief 0: Keep frequency synth on after command<br>
//!< 1: Turn frequency synth off after command
uint8_t bNoSync : 1 ; //!< \brief 0: Run sync search as normal for the configured mode<br>
//!< 1: Write correlation thresholds to the maximum value to avoid getting sync
} config ;
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} endTrigger ; //!< Trigger classifier for ending the operation
uint32_t syncWord ; //!< Sync word to use for receiver
ratmr_t endTime ; //!< Time to end the operation
} ;
//! @}
//! \addtogroup CMD_TX_TEST
//! @{
# define CMD_TX_TEST 0x0808
struct __RFC_STRUCT rfc_CMD_TX_TEST_s {
uint16_t commandNo ; //!< The command ID number 0x0808
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
struct {
uint8_t bUseCw : 1 ; //!< \brief 0: Send modulated signal<br>
//!< 1: Send continuous wave
uint8_t bFsOff : 1 ; //!< \brief 0: Keep frequency synth on after command<br>
//!< 1: Turn frequency synth off after command
uint8_t whitenMode : 2 ; //!< \brief 0: No whitening<br>
//!< 1: Default whitening<br>
//!< 2: PRBS-15<br>
//!< 3: PRBS-32
} config ;
uint8_t __dummy0 ;
uint16_t txWord ; //!< Value to send to the modem before whitening
uint8_t __dummy1 ;
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} endTrigger ; //!< Trigger classifier for ending the operation
uint32_t syncWord ; //!< Sync word to use for transmitter
ratmr_t endTime ; //!< Time to end the operation
} ;
//! @}
//! \addtogroup CMD_SYNC_STOP_RAT
//! @{
# define CMD_SYNC_STOP_RAT 0x0809
struct __RFC_STRUCT rfc_CMD_SYNC_STOP_RAT_s {
uint16_t commandNo ; //!< The command ID number 0x0809
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t __dummy0 ;
ratmr_t rat0 ; //!< \brief The returned RAT timer value corresponding to the value the RAT would have had when the
//!< RTC was zero
} ;
//! @}
//! \addtogroup CMD_SYNC_START_RAT
//! @{
# define CMD_SYNC_START_RAT 0x080A
struct __RFC_STRUCT rfc_CMD_SYNC_START_RAT_s {
uint16_t commandNo ; //!< The command ID number 0x080A
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t __dummy0 ;
ratmr_t rat0 ; //!< \brief The desired RAT timer value corresponding to the value the RAT would have had when the
//!< RTC was zero. This parameter is returned by CMD_SYNC_STOP_RAT
} ;
//! @}
//! \addtogroup CMD_COUNT
//! @{
# define CMD_COUNT 0x080B
struct __RFC_STRUCT rfc_CMD_COUNT_s {
uint16_t commandNo ; //!< The command ID number 0x080B
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t counter ; //!< \brief Counter. On start, the radio CPU decrements the value, and the end status of the operation
//!< differs if the result is zero
} ;
//! @}
//! \addtogroup CMD_FS_POWERUP
//! @{
# define CMD_FS_POWERUP 0x080C
struct __RFC_STRUCT rfc_CMD_FS_POWERUP_s {
uint16_t commandNo ; //!< The command ID number 0x080C
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t __dummy0 ;
uint32_t * pRegOverride ; //!< Pointer to a list of hardware and configuration registers to override. If NULL, no override is used.
} ;
//! @}
//! \addtogroup CMD_FS_POWERDOWN
//! @{
# define CMD_FS_POWERDOWN 0x080D
struct __RFC_STRUCT rfc_CMD_FS_POWERDOWN_s {
uint16_t commandNo ; //!< The command ID number 0x080D
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
} ;
//! @}
//! \addtogroup CMD_SCH_IMM
//! @{
# define CMD_SCH_IMM 0x0810
struct __RFC_STRUCT rfc_CMD_SCH_IMM_s {
uint16_t commandNo ; //!< The command ID number 0x0810
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t __dummy0 ;
uint32_t cmdrVal ; //!< Value as would be written to CMDR
uint32_t cmdstaVal ; //!< Value as would be returned in CMDSTA
} ;
//! @}
//! \addtogroup CMD_COUNT_BRANCH
//! @{
# define CMD_COUNT_BRANCH 0x0812
struct __RFC_STRUCT rfc_CMD_COUNT_BRANCH_s {
uint16_t commandNo ; //!< The command ID number 0x0812
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint16_t counter ; //!< \brief Counter. On start, the radio CPU decrements the value, and the end status of the operation
//!< differs if the result is zero
rfc_radioOp_t * pNextOpIfOk ; //!< Pointer to next operation if counter did not expire
} ;
//! @}
//! \addtogroup CMD_PATTERN_CHECK
//! @{
# define CMD_PATTERN_CHECK 0x0813
struct __RFC_STRUCT rfc_CMD_PATTERN_CHECK_s {
uint16_t commandNo ; //!< The command ID number 0x0813
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
struct {
uint16_t operation : 2 ; //!< \brief Operation to perform<br>
//!< 0: True if value == <code>compareVal</code><br>
//!< 1: True if value < <code>compareVal</code><br>
//!< 2: True if value > <code>compareVal</code><br>
//!< 3: <i>Reserved</i>
uint16_t bByteRev : 1 ; //!< \brief If 1, interchange the four bytes of the value, so that they are read
//!< most-significant-byte-first.
uint16_t bBitRev : 1 ; //!< If 1, perform bit reversal of the value
uint16_t signExtend : 5 ; //!< \brief 0: Treat value and <code>compareVal</code> as unsigned<br>
//!< 1–31: Treat value and <code>compareVal</code> as signed, where the value
//!< gives the number of the most significant bit in the signed number.
uint16_t bRxVal : 1 ; //!< \brief 0: Use <code>pValue</code> as a pointer<br>
//!< 1: Use <code>pValue</code> as a signed offset to the start of the last
//!< committed Rx entry element
} patternOpt ; //!< Options for comparison
rfc_radioOp_t * pNextOpIfOk ; //!< Pointer to next operation if comparison result was true
uint8_t * pValue ; //!< Pointer to read from, or offset from last Rx entry if <code>patternOpt.bRxVal</code> == 1
uint32_t mask ; //!< Bit mask to apply before comparison
uint32_t compareVal ; //!< Value to compare to
} ;
//! @}
//! \addtogroup CMD_TX_POWER_BOOST
//! @{
# define CMD_TX_POWER_BOOST 0x0816
struct __RFC_STRUCT rfc_CMD_TX_POWER_BOOST_s {
uint16_t commandNo ; //!< The command ID number 0x0816
uint16_t status ; //!< \brief An integer telling the status of the command. This value is
//!< updated by the radio CPU during operation and may be read by the
//!< system CPU at any time.
rfc_radioOp_t * pNextOp ; //!< Pointer to the next operation to run after this operation is done
ratmr_t startTime ; //!< Absolute or relative start time (depending on the value of <code>startTrigger</code>)
struct {
uint8_t triggerType : 4 ; //!< The type of trigger
uint8_t bEnaCmd : 1 ; //!< \brief 0: No alternative trigger command<br>
//!< 1: CMD_TRIGGER can be used as an alternative trigger
uint8_t triggerNo : 2 ; //!< The trigger number of the CMD_TRIGGER command that triggers this action
uint8_t pastTrig : 1 ; //!< \brief 0: A trigger in the past is never triggered, or for start of commands, give an error<br>
//!< 1: A trigger in the past is triggered as soon as possible
} startTrigger ; //!< Identification of the trigger that starts the operation
struct {
uint8_t rule : 4 ; //!< Condition for running next command: Rule for how to proceed
uint8_t nSkip : 4 ; //!< Number of skips if the rule involves skipping
} condition ;
uint8_t vddrLevel ; //!< \brief VDDR level to set<br>
//!< 0xFD: Trim VDDR voltage to normal level (VDDR_TRIM), nominally 1.68 V<br>
//!< 0xFE: Trim VDDR voltage to high level (VDDR_TRIM_H), nominally 1.85 V<br>
//!< 0xFF: Trim VDDR voltage to higher level (VDDR_TRIM_HH), nominally 1.95 V<br>
//!< Other: reserved
uint8_t paTrimValue ; //!< \brief Optional power amplifier trim setting manipulation<br>
//!< 0x00-0x1F: Value to write in ADI_0_RF:PACTL0.TRIM register field<br>
//!< 0xFE: Set PACTL0.TRIM to its default value from FCFG1<br>
//!< 0xFF: Do not write PACTL0.TRIM, use the setting that is already applied<br>
} ;
//! @}
//! \addtogroup CMD_ABORT
//! @{
# define CMD_ABORT 0x0401
struct __RFC_STRUCT rfc_CMD_ABORT_s {
uint16_t commandNo ; //!< The command ID number 0x0401
} ;
//! @}
//! \addtogroup CMD_STOP
//! @{
# define CMD_STOP 0x0402
struct __RFC_STRUCT rfc_CMD_STOP_s {
uint16_t commandNo ; //!< The command ID number 0x0402
} ;
//! @}
//! \addtogroup CMD_GET_RSSI
//! @{
# define CMD_GET_RSSI 0x0403
struct __RFC_STRUCT rfc_CMD_GET_RSSI_s {
uint16_t commandNo ; //!< The command ID number 0x0403
} ;
//! @}
//! \addtogroup CMD_UPDATE_RADIO_SETUP
//! @{
# define CMD_UPDATE_RADIO_SETUP 0x0001
struct __RFC_STRUCT rfc_CMD_UPDATE_RADIO_SETUP_s {
uint16_t commandNo ; //!< The command ID number 0x0001
uint16_t __dummy0 ;
uint32_t * pRegOverride ; //!< Pointer to a list of hardware and configuration registers to override
} ;
//! @}
//! \addtogroup CMD_TRIGGER
//! @{
# define CMD_TRIGGER 0x0404
struct __RFC_STRUCT rfc_CMD_TRIGGER_s {
uint16_t commandNo ; //!< The command ID number 0x0404
uint8_t triggerNo ; //!< Command trigger number
} ;
//! @}
//! \addtogroup CMD_GET_FW_INFO
//! @{
# define CMD_GET_FW_INFO 0x0002
struct __RFC_STRUCT rfc_CMD_GET_FW_INFO_s {
uint16_t commandNo ; //!< The command ID number 0x0002
uint16_t versionNo ; //!< Firmware version number
uint16_t startOffset ; //!< The start of free RAM
uint16_t freeRamSz ; //!< The size of free RAM
uint16_t availRatCh ; //!< Bitmap of available RAT channels
} ;
//! @}
//! \addtogroup CMD_START_RAT
//! @{
# define CMD_START_RAT 0x0405
struct __RFC_STRUCT rfc_CMD_START_RAT_s {
uint16_t commandNo ; //!< The command ID number 0x0405
} ;
//! @}
//! \addtogroup CMD_PING
//! @{
# define CMD_PING 0x0406
struct __RFC_STRUCT rfc_CMD_PING_s {
uint16_t commandNo ; //!< The command ID number 0x0406
} ;
//! @}
//! \addtogroup CMD_ADD_DATA_ENTRY
//! @{
# define CMD_ADD_DATA_ENTRY 0x0005
struct __RFC_STRUCT rfc_CMD_ADD_DATA_ENTRY_s {
uint16_t commandNo ; //!< The command ID number 0x0005
uint16_t __dummy0 ;
dataQueue_t * pQueue ; //!< Pointer to the queue structure to which the entry will be added
uint8_t * pEntry ; //!< Pointer to the entry
} ;
//! @}
//! \addtogroup CMD_REMOVE_DATA_ENTRY
//! @{
# define CMD_REMOVE_DATA_ENTRY 0x0006
struct __RFC_STRUCT rfc_CMD_REMOVE_DATA_ENTRY_s {
uint16_t commandNo ; //!< The command ID number 0x0006
uint16_t __dummy0 ;
dataQueue_t * pQueue ; //!< Pointer to the queue structure from which the entry will be removed
uint8_t * pEntry ; //!< Pointer to the entry that was removed
} ;
//! @}
//! \addtogroup CMD_FLUSH_QUEUE
//! @{
# define CMD_FLUSH_QUEUE 0x0007
struct __RFC_STRUCT rfc_CMD_FLUSH_QUEUE_s {
uint16_t commandNo ; //!< The command ID number 0x0007
uint16_t __dummy0 ;
dataQueue_t * pQueue ; //!< Pointer to the queue structure to be flushed
uint8_t * pFirstEntry ; //!< Pointer to the first entry that was removed
} ;
//! @}
//! \addtogroup CMD_CLEAR_RX
//! @{
# define CMD_CLEAR_RX 0x0008
struct __RFC_STRUCT rfc_CMD_CLEAR_RX_s {
uint16_t commandNo ; //!< The command ID number 0x0008
uint16_t __dummy0 ;
dataQueue_t * pQueue ; //!< Pointer to the queue structure to be cleared
} ;
//! @}
//! \addtogroup CMD_REMOVE_PENDING_ENTRIES
//! @{
# define CMD_REMOVE_PENDING_ENTRIES 0x0009
struct __RFC_STRUCT rfc_CMD_REMOVE_PENDING_ENTRIES_s {
uint16_t commandNo ; //!< The command ID number 0x0009
uint16_t __dummy0 ;
dataQueue_t * pQueue ; //!< Pointer to the queue structure to be flushed
uint8_t * pFirstEntry ; //!< Pointer to the first entry that was removed
} ;
//! @}
//! \addtogroup CMD_SET_RAT_CMP
//! @{
# define CMD_SET_RAT_CMP 0x000A
struct __RFC_STRUCT rfc_CMD_SET_RAT_CMP_s {
uint16_t commandNo ; //!< The command ID number 0x000A
uint8_t ratCh ; //!< The radio timer channel number
uint8_t __dummy0 ;
ratmr_t compareTime ; //!< The time at which the compare occurs
} ;
//! @}
//! \addtogroup CMD_SET_RAT_CPT
//! @{
# define CMD_SET_RAT_CPT 0x0603
struct __RFC_STRUCT rfc_CMD_SET_RAT_CPT_s {
uint16_t commandNo ; //!< The command ID number 0x0603
struct {
uint16_t : 3 ;
uint16_t inputSrc : 5 ; //!< Input source indicator
uint16_t ratCh : 4 ; //!< The radio timer channel number
uint16_t bRepeated : 1 ; //!< \brief 0: Single capture mode<br>
//!< 1: Repeated capture mode
uint16_t inputMode : 2 ; //!< \brief Input mode:<br>
//!< 0: Capture on rising edge<br>
//!< 1: Capture on falling edge<br>
//!< 2: Capture on both edges<br>
//!< 3: <i>Reserved</i>
} config ;
} ;
//! @}
//! \addtogroup CMD_DISABLE_RAT_CH
//! @{
# define CMD_DISABLE_RAT_CH 0x0408
struct __RFC_STRUCT rfc_CMD_DISABLE_RAT_CH_s {
uint16_t commandNo ; //!< The command ID number 0x0408
uint8_t ratCh ; //!< The radio timer channel number
} ;
//! @}
//! \addtogroup CMD_SET_RAT_OUTPUT
//! @{
# define CMD_SET_RAT_OUTPUT 0x0604
struct __RFC_STRUCT rfc_CMD_SET_RAT_OUTPUT_s {
uint16_t commandNo ; //!< The command ID number 0x0604
struct {
uint16_t : 2 ;
uint16_t outputSel : 3 ; //!< Output event indicator
uint16_t outputMode : 3 ; //!< \brief 0: Set output line low as default; and pulse on event. Duration of pulse is one RF Core clock period (ca. 41.67 ns).<br>
//!< 1: Set output line high on event<br>
//!< 2: Set output line low on event<br>
//!< 3: Toggle (invert) output line state on event<br>
//!< 4: Immediately set output line to low (does not change upon event)<br>
//!< 5: Immediately set output line to high (does not change upon event)<br>
//!< Others: <i>Reserved</i>
uint16_t ratCh : 4 ; //!< The radio timer channel number
} config ;
} ;
//! @}
//! \addtogroup CMD_ARM_RAT_CH
//! @{
# define CMD_ARM_RAT_CH 0x0409
struct __RFC_STRUCT rfc_CMD_ARM_RAT_CH_s {
uint16_t commandNo ; //!< The command ID number 0x0409
uint8_t ratCh ; //!< The radio timer channel number
} ;
//! @}
//! \addtogroup CMD_DISARM_RAT_CH
//! @{
# define CMD_DISARM_RAT_CH 0x040A
struct __RFC_STRUCT rfc_CMD_DISARM_RAT_CH_s {
uint16_t commandNo ; //!< The command ID number 0x040A
uint8_t ratCh ; //!< The radio timer channel number
} ;
//! @}
//! \addtogroup CMD_SET_TX_POWER
//! @{
# define CMD_SET_TX_POWER 0x0010
struct __RFC_STRUCT rfc_CMD_SET_TX_POWER_s {
uint16_t commandNo ; //!< The command ID number 0x0010
struct {
uint16_t IB : 6 ; //!< Value to write to the PA power control field at 25 °C
uint16_t GC : 2 ; //!< Value to write to the gain control of the 1st stage of the PA
uint16_t boost : 1 ; //!< Value of boost bit in synth
uint16_t tempCoeff : 7 ; //!< Temperature coefficient for IB. 0: No temperature compensation
} txPower ; //!< New Tx power setting
} ;
//! @}
//! \addtogroup CMD_UPDATE_FS
//! @{
# define CMD_UPDATE_FS 0x0011
struct __RFC_STRUCT rfc_CMD_UPDATE_FS_s {
uint16_t commandNo ; //!< The command ID number 0x0011
uint16_t frequency ; //!< The frequency in MHz to tune to
uint16_t fractFreq ; //!< Fractional part of the frequency to tune to
} ;
//! @}
//! \addtogroup CMD_BUS_REQUEST
//! @{
# define CMD_BUS_REQUEST 0x040E
struct __RFC_STRUCT rfc_CMD_BUS_REQUEST_s {
uint16_t commandNo ; //!< The command ID number 0x040E
uint8_t bSysBusNeeded ; //!< \brief 0: System bus may sleep<br>
//!< 1: System bus access needed
} ;
//! @}
//! @}
//! @}
# endif /* COMMON_CMD_H_ */
