osd-contiki/platform/avr-ravenlcd/sleep.c

163 lines
5 KiB
C
Raw Permalink Normal View History

/*
* Copyright (c) 2008 Swedish Institute of Computer Science
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of the copyright holders nor the names of
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/**
* \file
*
* \brief
* This controls the sleep operation for the LCD.
*
* \author
* Mike Vidales mavida404@gmail.com
*
*/
#include <avr/interrupt.h>
#include <avr/sleep.h>
#include <avr/wdt.h>
#include <util/delay.h>
#include <stdbool.h>
#include "main.h"
#include "sleep.h"
#include "uart.h"
#include "key.h"
#include "timer.h"
#include "lcd.h" //temp
/**
* \addtogroup lcd
* \{
*/
/*---------------------------------------------------------------------------*/
/**
* \brief Prepares for and executes sleep. This function sets up the
* processor to enter sleep mode, and to wake up when the joystick
* button (PE2/PCINT2) is pressed or after the specified interval.
*
* \param howlong Seconds to sleep, 0=until button pushed
*/
void
sleep_now(int howlong)
{
/* Disable watchdog (not currently used elsewhere) */
wdt_disable();
/* Setup sleep mode */
if (howlong==0) {
set_sleep_mode(SLEEP_MODE_PWR_DOWN);
MCUCR |= (1<<JTD); //Disable JTAG so clock can stop
} else {
set_sleep_mode(SLEEP_MODE_PWR_SAVE);
/* Using 8 bit TIMER2 */
TCNT2 = 0;
TCCR2A = (1<<CS22)|(1<<CS21)|(1<<CS20); //Prescale by 1024
TIMSK2 = (1<<TOIE2); //Enable overflow interrupt
howlong*=30; //which is approximately 30 Hz
/* Using 16 bit TIMER1, which takes a bit more power
timer_stop; //Disable interrupt
timer_init; //make sure initialized for 1 second
timer_start; //Start timer, enable interrupt
*/
}
/* Enable pin change 0 wakeup interrupt */
EIMSK |= (1 << PCIE0);
/* Select joystick button input pin */
PCMSK0 |= (1 << PCINT2);
/* Sleep until timeout or button pushed */
while (ENTER_PORT & (1<<ENTER_PIN)) {
sleep_mode();
if (!howlong--) break;
}
/* Disable the interrupts for the enter button and TIMER2 */
EIMSK &= ~(1 << PCIE0);
PCMSK0&= ~(1 <<PCINT2);
TIMSK2&= ~(1 << TOIE2);
}
/*---------------------------------------------------------------------------*/
/**
* \brief This will send a wakeup command to ATmega1284p
* It may already be awake, if not it will respond during the next wake cycle
* Upon receiving the command it will return an acknowledgement frame
*
* \brief This will send a single character forever to the ATmega1284p to cause a wakeup.
* The 1284p polls the USART for new data during each sleep cycle. Upon receiving a
* character from the user LCD, it will wake up and send an acknowledgement frame.
*/
void
sleep_wakeup(void)
{
lcd_puts_P(PSTR("WAKE 1284p"));
/* Flood 1284p with wake commands until it responds*/
for(;;){
uart_serial_send_frame(SEND_WAKE,0,0);
_delay_us(1000);
if (rx_char_ready())
break;
}
/* Get a frame back */
uart_serial_rcv_frame(true);
}
/*---------------------------------------------------------------------------*/
/**
* \brief This is the wake up button interrupt. When this interrupt fires,
* nothing is done. The program will simply continue from the end of the sleep
* command.
*/
ISR
(PCINT0_vect)
{
}
/*---------------------------------------------------------------------------*/
/**
* \brief This is the timer2 overflow interrupt. When this interrupt fires,
* the CPU will wake.
*/
ISR
(TIMER2_OVF_vect)
{
}
/** \} */