91 lines
3.2 KiB
C
91 lines
3.2 KiB
C
|
/*
|
||
|
|
* Copyright (c) 2012, BinaryLabs.
|
||
|
|
* All rights reserved.
|
||
|
|
*
|
||
|
|
* Redistribution and use in source and binary forms, with or without
|
||
|
|
* modification, are permitted provided that the following conditions
|
||
|
|
* are met:
|
||
|
|
* 1. Redistributions of source code must retain the above copyright
|
||
|
|
* notice, this list of conditions and the following disclaimer.
|
||
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
||
|
|
* notice, this list of conditions and the following disclaimer in the
|
||
|
|
* documentation and/or other materials provided with the distribution.
|
||
|
|
* 3. Neither the name of the Institute nor the names of its contributors
|
||
|
|
* may be used to endorse or promote products derived from this software
|
||
|
|
* without specific prior written permission.
|
||
|
|
*
|
||
|
|
* THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ``AS IS'' AND
|
||
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
||
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
|
||
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
||
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
||
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
||
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
||
|
|
* SUCH DAMAGE.
|
||
|
|
*
|
||
|
|
* @(#)$Id: battery-sensor.h,v 1.1 2012/08/25 19:34:06 nifi Exp $
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* \file
|
||
|
|
* Battery sensor file for Atmega128rfa1.
|
||
|
|
* \author
|
||
|
|
* Paulo Louro <paulolouro@binarylabs.dk>
|
||
|
|
* Harald Pichler <harald@the-develop.net>
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
*The atmel rf23x radios have a low voltage detector that can be configured in units of 75 millivolts. Here is example *code for the ATmega128rfa1, where the BATMON register is in extended io space [dak664]
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include "dev/battery-sensor.h"
|
||
|
|
#include "dev/batmon.h"
|
||
|
|
|
||
|
|
const struct sensors_sensor battery_sensor;
|
||
|
|
/*---------------------------------------------------------------------------*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* \return Voltage on battery measurement with BATMON register.
|
||
|
|
*/
|
||
|
|
static int
|
||
|
|
value(int type)
|
||
|
|
{
|
||
|
|
|
||
|
|
uint16_t h;
|
||
|
|
/*
|
||
|
|
uint8_t p1;
|
||
|
|
BATMON = 16; //give BATMON time to stabilize at highest range and lowest voltage
|
||
|
|
|
||
|
|
// Bandgap can't be measured against supply voltage in this chip.
|
||
|
|
// Use BATMON register instead
|
||
|
|
for ( p1=16; p1<31; p1++) {
|
||
|
|
BATMON = p1;
|
||
|
|
clock_delay_usec(100); // delay needed !!
|
||
|
|
if ((BATMON&(1<<BATMON_OK))==0) break;
|
||
|
|
}
|
||
|
|
h=2550-75*16-75+75*p1; //-75 to take the floor of the 75 mv transition window
|
||
|
|
*/
|
||
|
|
batmon_get_voltage(&h);
|
||
|
|
return h;
|
||
|
|
}
|
||
|
|
/*---------------------------------------------------------------------------*/
|
||
|
|
static int
|
||
|
|
configure(int type, int c)
|
||
|
|
{
|
||
|
|
// No configuration needed. readADC() handles all the config needed.
|
||
|
|
batmon_init();
|
||
|
|
return type == SENSORS_ACTIVE;
|
||
|
|
}
|
||
|
|
/*---------------------------------------------------------------------------*/
|
||
|
|
static int
|
||
|
|
status(int type)
|
||
|
|
{
|
||
|
|
// analog sensors are always ready
|
||
|
|
return 1;
|
||
|
|
}
|
||
|
|
/*---------------------------------------------------------------------------*/
|
||
|
|
SENSORS_SENSOR(battery_sensor, BATTERY_SENSOR, value, configure, status);
|